Woodland Management Practices in Bronze Age, Bruszczewo, Poland

The article presents a study of wood excavated from archaeological site in Poland (2100–1650 BC). The large amount of collected samples created a unique opportunity for research because the subfossil wood was in very good preservation state. This made it possible to carry out dendrotypological analysis. This is the first such study conducted for Early Bronze Age timber originating from Poland. The main goal of the study was to determine whether the presence of strong and abrupt reductions and releases of growth, observed within tree-ring sequences, is due to natural stand dynamics, results from the influence of extreme environmental factors or whether they should be linked to specific silvicultural practices already known in ancient times. Another purpose of the study was to determine the type of forest management techniques applied to the trees growing in Bruszczewo site. The research was conducted using the dendrochronological method. In addition to the measurements of growth-ring width, the development of earlywood and latewood zones, the proportion of sapwood and the presence of specific features of tree trunks were analysed. A detailed study allowed identifying the samples originating from coppiced and shredded trees. A characteristic feature of the trees subjected to these silvicultural practices is the presence of strong and abrupt reductions and releases of growth. Moreover, coppiced trees were specified by the large proportion of sapwood in the cross-section of the stem, reduced number of sapwood rings, small and numerous earlywood vessels, diminished earlywood vessels area. In turn, shredded trees distinguished themselves by a strong reduction in the earlywood width in the years following the shredding event. The research of archaeological wood from the ancient settlement proves that during the Early Bronze Age various forest management techniques were used in this site. These treatments were aimed at improving the quality and quantity of the raw material harvested from forest areas.

Prediction of shear strength parallel to grain in clear wood of oak (Quercus robur L.) on the basis of shear plane orientation, density and anatomical traits

Oak wood is popular for use in construction and as flooring. Evaluating the mechanical strength of oak timber is difficult and time consuming. Therefore, models for predicting mechanical properties, based on easy-to-obtain variables, may be useful. The purpose of the study was to build models for predicting shear strength parallel-to-grain in oak clear wood. With this goal, the shearing resistance was tested on 198 defect-free specimens (target dimensions 50 × 50 mm in tested section) obtained from a sample of 40 oak trees felled in north-western Spain. The mean shear strength of the sampled oak wood provenance was 15 N mm−2, which was almost equal to the highest mean value reported in previous studies. Analysis of the relationships between the variables tested enabled development of a model relating shear strength parallel to grain at 12% moisture content, with air-dry wood density and angle between tangential and shear plane as predictor variables ( R adj 2 ${R}_{\text{adj}}^{2}$ = 0.61, p < 0.01, bias = −0.80%, RMSE = 13.66%, for wood with wavy grain; R adj 2 ${R}_{\text{adj}}^{2}$ = 0.36, p < 0.01, bias = −1.46%, RMSE = 17.22%, for wood without wavy grain). The independence of shear strength relative to the presence/absence of sapwood or the annual growth ring width was also demonstrated.

A COMPARATIVE STUDY ON THE PHYSICAL AND MECHANICAL PROPERTIES OF DAHURIAN LARCH AND JAPANESE LARCH GROWN IN KOREA

To compare the wood quality of Dahurian larch and Japanese larch growing in Korea, the physical and mechanical properties were examined using the Korean standards. The proportion of heartwood was 82% and 72% in Dahurian and Japanese larch, respectively. The percentage of latewood was 42% in Dahurian larch and 35% in Japanese larch. The growth ring width of Dahurian larch was narrower than that of Japanese larch. Dahurian larch showed about 20% higher green moisture content compare to Japanese larch wood. Density and shrinkage of Dahurian larch were higher than Japanese larch. Axial compression strength, young`s modulus in compression, and shearing strength in heartwood of Dahurian larch were 11 MPa, 686 MPa, and 2.3 MPa, respectively, showing higher value than Japanese larch. The hardness was in the range of 13.8–38.7 MPa in Dahurian larch and 17.7–48.4 MPa in Japanese larch. The compression strength parallel to the grain and shearing strength in both species were significantly correlated with oven-dried density. Besides, the hardness in Dahurian larch was significantly correlated with latewood percentage and oven-dried density. In conclusion, the differences in the properties of both species were revealed and the results can be used for quality indices of both wood species.

MECHANICAL PROPERTIES OF POLISH-GROWN PINUS SYLVESTRIS L. STRUCTURAL SAWN TIMBER FROM THE BUTT, MIDDLE AND TOP LOGS

The research consisted in testing Polish sawn timber dedicated for construction applications made of pines (Pinus sylvestris L.) that grew in the Silesian Forestry Region, taking into account three parts of the log: butt, middle and top. The boards had the same cross section, a nominal thickness of 40 mm and width of 138 mm, typical for Polish structural timber. The mean nominal length of the boards under research amounted to 3500 mm. Each set was composed of 70 boards. Before the tests, boards were dried in an industrial drier until reaching the moisture content of 12%, and they were planed on 4 sides. First of all, the sawn timber was graded into strength classes, and their dynamic modulus of elasticity (MOE_dyn) was tested with a non-destructive method, with the use of a portable MTG device. The next step consisted in a bending test with four points of support, according to the EN 408 standard, and with the use of the TiraTest 2300 machine, in order to determine the global modulus of elasticity (MOE_EN-408) and the static bending strength, also referred to as modulus of rupture (MOR). Finally, the average growth ring width was determined for each board (PN-D-94021), as well as wood density according to EN-408. The hereby paper presents the test results for all the tested sawn timber boards, taking into account the part of log that each board came from: butt, middle or top. The hereby paper presents the influence of density on the mechanical properties of wood, taking into account the location on the round timber. The analysis does not include the influence of the width of annual growth rings and the proportion of latewood on the wood properties under research.

Characterization and comparison of the wood anatomical traits of plantation grown Quercus acutissima and Quercus variabilis

Oaks are important tree species, providing essential biomaterial for the wood industry. We characterize and compare wood anatomical traits of plantation grown Quercus acutissima Carruth. and Q. variabilis Blume to provide more detailed information to understand xylem radial growth, structure, and function, as well as differences between sapwood and heartwood, to provide data relevant for tree breeding and value-added wood utilization of oak plantations in China. In this study, radial strips were collected at breast height from the main trunk of the two species. Latewood percentage and growth ring width were investigated by X-ray densitometry and a Tree Ring Analysis System, respectively. Vessel and fibre lumen diameter, vessel and fibre wall thickness, vessel density, fibre wall thickness/diameter ratio, tissue proportions, and pit membrane thickness in between vasicentric tracheids were observed with light microscopy and electron microscopy and quantified. There were significant differences in a few wood anatomical traits between the two species: vessel wall thickness and vessel lumen diameter were higher in Q. acutissima than in Q. variabilis, while higher axial parenchyma proportion in sapwood was found in Q. variabilis than in Q. acutissima. More abundant tyloses were found in heartwood than in sapwood of both species. Our work showed the intraspecific and interspecific variation of the two species. Most differences between sapwood and heartwood must be attributed to differences in cambial age during their formation.

Characterisation of Pinus canariensis C.Sm. ex DC. Sawn Timber from Reforested Trees on the Island of Tenerife, Spain

Canary Island pine (Pinus canariensis C.Sm. ex DC) is a species endemic to the Canary Islands (Spain) that was for centuries overexploited for its wood and resin. Due to the state of the pine forest, more than 10,000 hectares were reforested in the middle of the 20th century. Now, under the silvicultural management plan, thinning operations have allowed Canary Island pine wood to be mechanically characterised for the first time using large test pieces. In total, 1529 pieces measuring 2600 × 120 × 35 mm and visually graded according to Spanish standard UNE 56544 (Visual grading of large structural coniferous sawn timber) were assessed, resulting in 872 pieces in grades ME-1 and ME-2 and 657 rejects. After the characteristic values of density (479–453 kg∙m−3), modulus of elasticity (MOE) (14,023–11,276 N∙mm−2) and bending strength (MOR) (26–14 N∙mm−2) were determined for both grades (ME-1 and ME-2), strength class C24 was assigned to grade ME-1, with similar values to Pinus radiata D.Don and Pinus pinaster Aiton, and C14 was assigned to grade ME-2. Density, number of growth rings, growth ring width, and presence/absence of resinous wood have a significant influence on MOE and MOR, for a confidence level of 95%. Reforestation of Canary Island pine not only allows restoration of the forest cover, but also provides an opportunity, through thinning, to obtain quality wood, helping to create employment and associated industry. This local example with an endemic species can be extrapolated to other parts of the world.

Influence of pine (Pinus sylvestris L.) growth rings width on the strength properties of structural sawn timber

Annual growth ring width was considered relative to the mechanical properties of timber from the Silesian Forestry Region in Poland. The timber was acquired from raw wood aged approximately 120 years old, with log quality A, B, and C. The study was conducted on 210 pieces of timber; 70 of them were from each part of the log: butt, middle, and top. The tested parameters, modulus of elasticity (MOE) and modulus of rupture (MOR), were measured on fully dimensional timber (40 × 138 × 3500 mm3) that had been dried and planed in industrial conditions. The density of wood (stereometric method) and annual rings width were calculated after MOR and MOE determination on samples including the entire cross-section cut near the failure zone. The tests revealed that the correlation between the width of growth rings and MOE or MOR depended on the log area: it was the highest for timber from butt logs and the lowest for timber from top logs. Moreover, the correlation between growth ring width and MOE or MOR depended also on the quality class of the logs from which the samples were obtained: it was the highest for timber from class A, and the lowest for class C.

Climate signals from intra-annual wood density fluctuations in Abies durangensis

ABSTRACTOngoing climate change is expected to alter forests by affecting forest productivity, with implications for the ecological functions of these systems. Despite its great dendrochronological potential, little research has been conducted into the use of wood density as a proxy for determining sensitivity to climate variability in Mexico. The response of Abies durangensis Martínez, in terms of wood density and growth ring width, to monthly climatic values (mean temperature, accumulated precipitation and the drought index SPEI) was analyzed through correlation analysis. Abies durangensis presents a high response, in terms of radial growth, to climatic conditions. Tree-ring widths are more sensitive to hydroclimatic variables, whereas wood density values are more sensitive to temperature. In particular, mean (MeanD) and minimum (MND) wood density values are more sensitive to climate than maximum (MXD). We found very marked spatial variations that indicate that A. durangensis responds differently to drought conditions depending on the indices of density.