Effect of Niobium on the Formation of Nano/Ultrafine Grain Structure in a Low Carbon Steel by Thermomechanical Treatment

2013 ◽  
pp. 63-70
Author(s):  
M. Abbasi ◽  
A. Kermanpur ◽  
A. Najafizadeh
Keyword(s):  
Carbon Steel ◽  
Thermomechanical Treatment ◽  
Low Carbon Steel ◽  
Grain Structure ◽  
Ultrafine Grain ◽  
Low Carbon ◽  
Ultrafine Grain Structure

An anomaly of the temperature dependence of the impact strength of low-carbon steel with an ultrafine-grain structure

2016 ◽  
Vol 61 (1) ◽  
pp. 15-18 ◽  
Author(s):  
I. M. Safarov ◽  
A. V. Korznikov ◽  
R. M. Galeyev ◽  
S. N. Sergeev ◽  
S. V. Gladkovsky ◽  
...  
Keyword(s):  
Carbon Steel ◽  
Impact Strength ◽  
Temperature Dependence ◽  
Low Carbon Steel ◽  
Grain Structure ◽  
Ultrafine Grain ◽  
Low Carbon ◽  
Ultrafine Grain Structure ◽  
The Impact

scholarly journals Determination of the Elastic Tensor of a Textured Low-Carbon Steel

1993 ◽  
Vol 21 (1) ◽  
pp. 3-16 ◽  
Author(s):  
P. Spalthoff ◽  
W. Wunnike ◽  
C. Nauer-Gerhard ◽  
H. J. Bunge ◽  
E. Schneider
Keyword(s):  
Carbon Steel ◽  
Elastic Anisotropy ◽  
Low Carbon Steel ◽  
Elastic Stiffness ◽  
Ultrasonic Pulse ◽  
Grain Structure ◽  
Maximum Deviation ◽  
Low Carbon ◽  
The Hill ◽  
Pulse Echo

The components of the elastic stiffness tensor of hot rolled low-carbon steel were determined using an ultrasonic pulse-echo-method. They were also calculated on the basis of X-ray texture measurements using the Hill approximation. The maximum deviation between experimental and calculated values is 3.5%. An influence of the slightly anisotropic grain structure on the elastic anisotropy could not be seen.

Ultrafine-grain structure and properties of carbon-steel wire after complex deformation

2014 ◽  
Vol 44 (5) ◽  
pp. 390-393 ◽  
Author(s):  
M. A. Polyakova ◽  
A. E. Gulin ◽  
O. A. Nikitenko ◽  
D. V. Konstantinov ◽  
M. S. Zherebtsov
Keyword(s):  
Carbon Steel ◽  
Steel Wire ◽  
Grain Structure ◽  
Ultrafine Grain ◽  
Structure And Properties ◽  
Complex Deformation ◽  
Ultrafine Grain Structure

Grain Structure of Aluminum-Killed, Low Carbon Steel Sheets

JOM ◽  
1951 ◽  
Vol 3 (9) ◽  
pp. 721-726 ◽  
Author(s):  
R. L. Solter ◽  
C. W. Beattie
Keyword(s):  
Carbon Steel ◽  
Low Carbon Steel ◽  
Grain Structure ◽  
Low Carbon ◽  
Steel Sheets

THE FORMATION OF ULTRAFINE FERRITE THROUGH STATIC TRANSFORMATION IN LOW CARBON STEELS

2008 ◽  
Vol 22 (18n19) ◽  
pp. 2804-2813
Author(s):  
Y. ADACHI ◽  
M. WAKITA ◽  
H. BELADI ◽  
P. D. HODGSON
Keyword(s):  
Deformation Temperature ◽  
Carbon Steels ◽  
Grain Structure ◽  
Dynamic Strain ◽  
Ultrafine Grain ◽  
Low Carbon ◽  
Low Carbon Steels ◽  
Novel Approach ◽  
Wide Range ◽  
Ultrafine Grain Structure

A novel approach was used to produce an ultrafine grain structure in low carbon steels with a wide range of hardenability. This included warm deformation of supercooled austenite followed by reheating in the austenite region and cooling (RHA). The ultrafine ferrite structure was independent of steel composition. However, the mechanism of ferrite refinement changed with the steel quench hardenability. In a relatively low hardenable steel, the ultrafine structure was produced through dynamic strain induced transformation, whereas the ferrite refinement was formed by static transformation in steels with high quench hardenability. The use of a model Ni -30 Fe austenitic alloy revealed that the deformation temperature has a strong effect on the nature of the intragranular defects. There was a transition temperature below which the cell dislocation structure changed to laminar microbands. It appears that the extreme refinement of ferrite is due to the formation of extensive high angle intragranular defects at these low deformation temperature that then act as sites for static transformation.

Sign in / Sign up

Export Citation Format

Share Document