Relationship Between Reaction Rate of Perfluorocarboxylic Acid Decomposition at a Plasma-Liquid Interface and Adsorbed Amount

The decomposition of peroxobenzoic acid in benzene was studied, and catalytic effects of Fe(III), Mn(III), Co(II), Co(III), and Cr(III) on the reaction rate and the composition of the reaction mixture were investigated. An analogous experiment carried out in perdeuterobenzene and determination of the distribution of deuterium in the reaction products provided evidence for the participation of the solvent in peroxobenzoic acid decomposition.

Download Full-text

SN2 Reaction Rate Enhancement by β-Cyclodextrin at the Liquid/Liquid Interface

The Journal of Physical Chemistry C ◽

10.1021/acs.jpcc.7b05091 ◽

2017 ◽

Vol 121 (35) ◽

pp. 19209-19217 ◽

Cited By ~ 5

Author(s):

John J. Karnes ◽

Ilan Benjamin

Keyword(s):

Reaction Rate ◽

Liquid Interface ◽

Rate Enhancement ◽

Sn2 Reaction

Download Full-text

Relationship between Reaction Rate of Perfluorocarboxylic Acids Decomposition at the Interface of Plasma-Liquid and Adsorbed Amount

IEEJ Transactions on Fundamentals and Materials ◽

10.1541/ieejfms.132.1027 ◽

2012 ◽

Vol 132 (11) ◽

pp. 1027-1032 ◽

Cited By ~ 4

Author(s):

Yuriko Matsuya ◽

Nozomi Takeuchi ◽

Koichi Yasuoka

Keyword(s):

Reaction Rate ◽

Adsorbed Amount ◽

Perfluorocarboxylic Acids

Download Full-text

Locating Al in the DABCO catalyst before and after Al extraction

Proceedings, annual meeting, Electron Microscopy Society of America ◽

10.1017/s0424820100174461 ◽

1990 ◽

Vol 48 (4) ◽

pp. 265-267

Author(s):

Kathleen B. Reuter

Keyword(s):

Active Site ◽

Inverse Relationship ◽

Transverse Direction ◽

Reaction Rate ◽

Acid Phosphate ◽

Fracture Surfaces ◽

Al Content ◽

Before And After ◽

Relationship Of

The reaction rate and efficiency of piperazine to 1,4-diazabicyclo-octane (DABCO) depends on the Si/Al ratio of the MFI topology catalysts. The Al was shown to be the active site, however, in the Si/Al range of 30-200 the reaction rate increases as the Si/Al ratio increases. The objective of this work was to determine the location and concentration of Al to explain this inverse relationship of Al content with reaction rate.Two silicalite catalysts in the form of 1/16 inch SiO2/Al2O3 bonded extrudates were examined: catalyst A with a Si/Al of 83; and catalyst B, the acid/phosphate Al extracted form of catalyst A, with a Si/Al of 175. Five extrudates from each catalyst were fractured in the transverse direction and particles were obtained from the fracture surfaces near the center of the extrudate diameter. Particles were also obtained from the outside surfaces of five extrudates.

Download Full-text

Direct observation of Fe-Al-Zn ternary intermetallic compound and its transformation during the early stage of hot-dip galvanizing

Proceedings, annual meeting, Electron Microscopy Society of America ◽

10.1017/s0424820100151416 ◽

1993 ◽

Vol 51 ◽

pp. 1116-1117

Author(s):

C. S. Lin ◽

W. A. Chiou ◽

M. Meshii

Keyword(s):

Intermetallic Compound ◽

Reaction Rate ◽

Diffusion Rate ◽

Early Stage ◽

Zinc Bath ◽

Steel Sheets ◽

Direct Observations ◽

Solid Iron ◽

Iron And Zinc ◽

Ternary Intermetallic Compound

The galvannealed steel sheets have received ever increased attention because of their excellent post-painting corrosion resistance and good weldability. However, its powdering and flaking tendency during press forming processes strongly impairs its performance. In order to optimize the properties of galvanneal coatings, it is critical to control the reaction rate between solid iron and molten zinc.In commercial galvannealing line, aluminum is added to zinc bath to retard the diffusion rate between iron and zinc by the formation of a thin layer of Al intermetallic compound on the surface of steel at initial hot-dip galvanizing. However, the form of this compound and its transformation are still speculated. In this paper, we report the direct observations of this compound and its transformation.The specimens were prepared in a hot-dip simulator in which the steel was galvanized in the zinc bath containing 0.14 wt% of Al at a temperature of 480 °C for 5 seconds and was quenched by liquid nitrogen.

Download Full-text