Modeling and Performance Analysis of Highly Efficient Copper Indium Gallium Selenide Solar Cell with Cu 2 O Hole Transport Layer Using Solar Cell Capacitance Simulator in One Dimension

2021 ◽  
pp. 2100512
Author(s):  
Most. Rifat Sultana ◽  
Benjer Islam ◽  
Sheikh Rashel Al Ahmed
Keyword(s):  
Solar Cell ◽  
Hole Transport ◽  
Transport Layer ◽  
One Dimension ◽  
Hole Transport Layer ◽  
Copper Indium Gallium Selenide ◽  
Copper Indium ◽  
And Performance ◽  
Cell Capacitance ◽  
Copper Indium Gallium

Comparative Study of Copper Indium Gallium Selenide (CIGS) Solar Cell With Other Solar Technologies

2021 ◽  
Author(s):  
Isabela C. B. ◽  
Ricardo Lameirinhas ◽  
Carlos A. F. Fernandes ◽  
João Paulo N. Torres
Keyword(s):  
Thin Film ◽  
Solar Cell ◽  
Comparative Study ◽  
Crystalline Silicon ◽  
Gallium Selenide ◽  
Copper Indium Gallium Selenide ◽  
Cigs Solar Cell ◽  
Copper Indium ◽  
Indium Gallium ◽  
Copper Indium Gallium

Thin-film modules are emerging in the photovoltaic market, due to their competitive cost with the traditional crystalline silicon modules. The thin-film cells CuIn(1-x)Ga(x)Se2 (Copper Indium Gallium Selenide - CIGS) are...

Materials Optimization for thin-film copper indium gallium selenide (CIGS) solar cell based on distributed braggs reflector

Optik ◽  
2020 ◽  
pp. 165987
Author(s):  
Waqas Farooq ◽  
Thamraa Alshahrani ◽  
Syed Asfandyar Ali Kazmi ◽  
Javed Iqbal ◽  
Hassnain Abbas Khan ◽  
...  
Keyword(s):  
Thin Film ◽  
Solar Cell ◽  
Gallium Selenide ◽  
Copper Indium Gallium Selenide ◽  
Cigs Solar Cell ◽  
Copper Indium ◽  
Indium Gallium ◽  
Copper Indium Gallium

Chalcogenide As Inorganic Transport Layer in Perovskite Solar Cell

2021 ◽  
Author(s):  
Atul kumar
Keyword(s):  
Solar Cell ◽  
Fill Factor ◽  
Perovskite Solar Cell ◽  
Hole Transport ◽  
Band Alignment ◽  
Transport Layer ◽  
Hole Transport Layer ◽  
Band Offset ◽  
Primary Concern ◽  
Earth Abundant

Abstract Fill factor (FF) deficit and stability is a primary concern with the perovskite solar cell. Resistance values and band alignment at junction interface in perovskite are causing low fill factor. Moisture sensitivity of methylammonium lead halide perovskite is causing a stability issue. We tried to solve these issues by using inorganic hole transport layer (HTL). FF is sensitive to the band offset values. We study the band alignment/band offset effect at the Perovskite /HTL junction. Inorganic material replacing Spiro-MeOTAD can enhance the stability of the device by providing an insulation from ambient. Our simulation study shows that the earth abundant p-type chalcogenide materials of SnS as HTL in perovskite is comparable to Spiro-MeOTAD efficiency.

Device modeling of non-fullerene organic solar cell by incorporating CuSCN as a hole transport layer using SCAPS

Optik ◽  
2021 ◽  
pp. 168457
Author(s):  
Bharti Sharma ◽  
A S Mathur ◽  
V K Rajput ◽  
I K Singh ◽  
B P Singh
Keyword(s):  
Solar Cell ◽  
Organic Solar Cell ◽  
Hole Transport ◽  
Transport Layer ◽  
Hole Transport Layer ◽  
Device Modeling

scholarly journals Performance Comparison of Different Hole Transport Layer Configurations in a Perovskite-based Solar Cell using SCAPS-1D Simulation

2021 ◽  
Author(s):  
Seyyedreza HOSSEİNİ ◽  
Nagihan DELİBAŞ ◽  
Mahsa BAHRAMGOUR ◽  
Alireza TABATABAEİ MASHAYEKH ◽  
Aligholi NİAİE
Keyword(s):  
Solar Cell ◽  
Performance Comparison ◽  
Hole Transport ◽  
Transport Layer ◽  
Hole Transport Layer

scholarly journals Hole Transport Behaviour of Various Polymers and Their Application to Perovskite-Sensitized Solid-State Solar Cells

2018 ◽  
Vol 2018 ◽  
pp. 1-6 ◽  
Author(s):  
Jeongmin Lim ◽  
Seong Young Kong ◽  
Yong Ju Yun
Keyword(s):  
Solar Cells ◽  
Solar Cell ◽  
Solid State ◽  
Perovskite Solar Cell ◽  
Hole Transport ◽  
Transport Layer ◽  
Hole Transport Layer ◽  
Good Efficiency ◽  
Promising Alternative ◽  
Transport Behaviour

Inorganic-organic mesoscopic solar cells become a promising alternative for conventional solar cells. We describe a CH3NH3PbI3 perovskite-sensitized solid-state solar cells with the use of different polymer hole transport materials such as 2,2′,7,7′-tetrakis-(N,N-di-p-methoxyphenyl-amine)-9,9′-spirobifluorene (spiro-OMeTAD), poly(3-hexylthiophene-2,5-diyl) (P3HT), and poly[[4,8-bis[(2-ethylhexyl)oxy]benzo[1,2-b:4,5-b′]dithiophene-2,6-diyl][3-fluoro-2-[(2-ethylhexyl)carbonyl]thieno[3,4-b]thiophenediyl]] (PTB7). The device with a spiro-OMeTAD-based hole transport layer showed the highest efficiency of 6.9%. Interestingly, the PTB7 polymer, which is considered an electron donor material, showed dominant hole transport behaviors in the perovskite solar cell. A 200 nm thin layer of PTB7 showed comparatively good efficiency (5.5%) value to the conventional spiro-OMeTAD-based device.

Sign in / Sign up

Export Citation Format

Share Document