Virtual Environment for Control Strategies Testing: A Hardware-in-the-Loop Approach

2021 ◽  
pp. 588-602
Author(s):  
Silvia Alpúsig ◽  
Edwin Pruna ◽  
Ivón Escobar
Keyword(s):  
Virtual Environment ◽  
Control Strategies ◽  
Hardware In The Loop

Evaluation of Signal Control Strategy Based on Hardware-in-the-Loop

2014 ◽  
Vol 505-506 ◽  
pp. 1122-1126
Author(s):  
Xiao Hua Zhao ◽  
Chen Chen ◽  
Jian Rong
Keyword(s):  
Travel Time ◽  
Traffic Flow ◽  
Virtual Environment ◽  
Control Strategy ◽  
Control Strategies ◽  
Simulation Software ◽  
Signal Control ◽  
Hardware In The Loop ◽  
Microscopic Traffic Simulation ◽  
Real Signal

To evaluate the performance of different signal control strategies in intersection, based on the Hardware-In-The-Loop (HITL) simulation technology, a HITL system was established to perform experiment. In the system, microscopic traffic simulation software VISSIM created a virtual environment, in which the traffic flow can be controlled by the real signal controller. One type of intersection and four degrees of traffic volume were designed in the simulation program and three control strategies were set in the signal controller. Twelve simulations were performed in the system. The analysis of travel time and queuing length indicates that different strategies has remarkable influence on travel time, but no significant effect on queuing length.

scholarly journals Power Hardware-in-the-Loop-Based Performance Analysis of Different Converter Controllers for Fast Active Power Regulation in Low-Inertia Power Systems

Energies ◽  
2021 ◽  
Vol 14 (11) ◽  
pp. 3274
Author(s):  
Jose Rueda Torres ◽  
Zameer Ahmad ◽  
Nidarshan Veera Kumar ◽  
Elyas Rakhshani ◽  
Ebrahim Adabi ◽  
...  
Keyword(s):  
Performance Evaluation ◽  
Power Systems ◽  
Real Time ◽  
Control Strategies ◽  
Active Power ◽  
Power Electronic ◽  
Hardware In The Loop ◽  
Digital Controllers ◽  
Power Regulation ◽  
The Impact

Future electrical power systems will be dominated by power electronic converters, which are deployed for the integration of renewable power plants, responsive demand, and different types of storage systems. The stability of such systems will strongly depend on the control strategies attached to the converters. In this context, laboratory-scale setups are becoming the key tools for prototyping and evaluating the performance and robustness of different converter technologies and control strategies. The performance evaluation of control strategies for dynamic frequency support using fast active power regulation (FAPR) requires the urgent development of a suitable power hardware-in-the-loop (PHIL) setup. In this paper, the most prominent emerging types of FAPR are selected and studied: droop-based FAPR, droop derivative-based FAPR, and virtual synchronous power (VSP)-based FAPR. A novel setup for PHIL-based performance evaluation of these strategies is proposed. The setup combines the advanced modeling and simulation functions of a real-time digital simulation platform (RTDS), an external programmable unit to implement the studied FAPR control strategies as digital controllers, and actual hardware. The hardware setup consists of a grid emulator to recreate the dynamic response as seen from the interface bus of the grid side converter of a power electronic-interfaced device (e.g., type-IV wind turbines), and a mockup voltage source converter (VSC, i.e., a device under test (DUT)). The DUT is virtually interfaced to one high-voltage bus of the electromagnetic transient (EMT) representation of a variant of the IEEE 9 bus test system, which has been modified to consider an operating condition with 52% of the total supply provided by wind power generation. The selected and programmed FAPR strategies are applied to the DUT, with the ultimate goal of ascertaining its feasibility and effectiveness with respect to the pure software-based EMT representation performed in real time. Particularly, the time-varying response of the active power injection by each FAPR control strategy and the impact on the instantaneous frequency excursions occurring in the frequency containment periods are analyzed. The performed tests show the degree of improvements on both the rate-of-change-of-frequency (RoCoF) and the maximum frequency excursion (e.g., nadir).

scholarly journals Power Hardware-in-the-Loop: Response of Power Components in Real-Time Grid Simulation Environment

Energies ◽  
2021 ◽  
Vol 14 (3) ◽  
pp. 593
Author(s):  
Moiz Muhammad ◽  
Holger Behrends ◽  
Stefan Geißendörfer ◽  
Karsten von Maydell ◽  
Carsten Agert
Keyword(s):  
Real Time ◽  
Power Distribution ◽  
Control Strategies ◽  
Power Grid ◽  
Energy System ◽  
Hardware In The Loop ◽  
Distribution Grid ◽  
Compensation Strategy ◽  
Software Environment ◽  
The Real

With increasing changes in the contemporary energy system, it becomes essential to test the autonomous control strategies for distributed energy resources in a controlled environment to investigate power grid stability. Power hardware-in-the-loop (PHIL) concept is an efficient approach for such evaluations in which a virtually simulated power grid is interfaced to a real hardware device. This strongly coupled software-hardware system introduces obstacles that need attention for smooth operation of the laboratory setup to validate robust control algorithms for decentralized grids. This paper presents a novel methodology and its implementation to develop a test-bench for a real-time PHIL simulation of a typical power distribution grid to study the dynamic behavior of the real power components in connection with the simulated grid. The application of hybrid simulation in a single software environment is realized to model the power grid which obviates the need to simulate the complete grid with a lower discretized sample-time. As an outcome, an environment is established interconnecting the virtual model to the real-world devices. The inaccuracies linked to the power components are examined at length and consequently a suitable compensation strategy is devised to improve the performance of the hardware under test (HUT). Finally, the compensation strategy is also validated through a simulation scenario.

scholarly journals Hardware-in-the-loop simulator of wind turbine emulator using labview

2019 ◽  
Vol 10 (2) ◽  
pp. 971
Author(s):  
Himani Himani ◽  
Navneet Sharma
Keyword(s):  
Wind Turbine ◽  
Condition Monitoring ◽  
Wind Turbines ◽  
Control Strategies ◽  
Hardware In The Loop ◽  
Data Acquisition Card ◽  
Terminal Voltage ◽  
The Uk ◽  
The University ◽  
University Of Manchester

<p><span>This paper describes the design and implementation of Hardware in the Loop (HIL) system D.C. motor based wind turbine emulator for the condition monitoring of wind turbines. Operating the HIL system, it is feasible to replicate the actual operative conditions of wind turbines in a laboratory environment. This method simply and cost-effectively allows evaluating the software and hardware controlling the operation of the generator. This system has been implemented in the LabVIEW based programs by using Advantech- USB-4704-AE Data acquisition card. This paper describes all the components of the systems and their operations along with the control strategies of WTE such as Pitch control and MPPT. Experimental results of the developed simulator using the test rig are benchmarked with the previously verified WT test rigs developed at the Durham University and the University of Manchester in the UK by using the generated current spectra of the generator. Electric subassemblies are most vulnerable to damage in practice, generator-winding faults have been introduced and investigated using the terminal voltage. This wind turbine simulator can be analyzed or reconfigured for the condition monitoring without the requirement of actual WT’s.</span></p>

HIL Testbed and Motion Control Strategy for the Hybrid Hydraulic-Electric Architecture (HHEA)

2021 ◽  
Author(s):  
Arpan Chatterjee ◽  
Perry Y. Li
Keyword(s):  
Motion Control ◽  
Control Strategy ◽  
Control Strategies ◽  
Electric Machines ◽  
Hardware In The Loop ◽  
System Efficiency ◽  
Electric Motors ◽  
Test Bed ◽  
Road Vehicles ◽  
Precise Control

Abstract The Hybrid Hydraulic-Electric Architecture (HHEA) was proposed in recent years to increase system efficiency of high power mobile machines and to reap the benefits of electrification without the need for large electric machines. It uses a set of common pressure rails to provide the majority of power hydraulically and small electric motors to modulate that power for precise control. This paper presents the development of a Hardware-in-the-loop (HIL) test-bed for testing motion control strategies for the HHEA. Precise motion control is important for off-road vehicles whose utility requires the machine being dexterous and performing tasks exactly as commanded. Motion control for the HHEA is challenging due to its intrinsic use of discrete pressure rail switches to minimize system efficiency or to keep the system within the torque capabilities of the electric motor. The motion control strategy utilizes two different controllers: a nominal passivity based back-stepping controller used in between pressure rail switches and a transition controller used to handle the event of a pressure rail switch. In this paper, the performance of the nominal control under various nominal and rail switching scenarios is experimentally evaluated on the HIL testbed.

Hardware-in-the-loop simulation environment for testing of tilt-rotor UAV's control strategies

2018 ◽  
Author(s):  
Arthur V.Lara ◽  
Iuro B. P. Nascimento ◽  
Janier Arias-Garcia ◽  
Leandro Buss Becker ◽  
Guilherme V. Raffo
Keyword(s):  
Control Strategies ◽  
Hardware In The Loop ◽  
Simulation Environment ◽  
Tilt Rotor

scholarly journals Hardware-in-the-Loop Operations With an Emulator Rig for SOFC Hybrid Systems

2017 ◽  
Author(s):  
Mario L. Ferrari ◽  
Alessandro Sorce ◽  
Aristide F. Massardo
Keyword(s):  
Fuel Cell ◽  
Real Time ◽  
Hybrid Systems ◽  
Control Strategies ◽  
Experimental Tests ◽  
Outlet Temperature ◽  
Hardware In The Loop ◽  
Set Point ◽  
The Real ◽  
System Components

This paper shows the Hardware-In-the-Loop (HIL) technique developed for the complete emulation of Solid Oxide Fuel Cell (SOFC) based hybrid systems. This approach is based on the coupling of an emulator test rig with a real-time software for components which are not included in the plant. The experimental facility is composed of a T100 microturbine (100 kW electrical power size) modified for the connection to an SOFC emulator device. This component is composed of both anodic and cathodic vessels including also the anodic recirculation system which is carried out with a single stage ejector, driven by an air flow in the primary duct. However, no real stack material was installed in the plant. For this reason, a real-time dynamic software was developed in the Matlab-Simulink environment including all the SOFC system components (the fuel cell stack with the calculation of the electrochemical aspects considering also the real losses, the reformer, and a cathodic recirculation based on a blower, etc.). This tool was coupled with the real system utilizing a User Datagram Protocol (UDP) data exchange approach (the model receives flow data from the plant at the inlet duct of the cathodic vessel, while it is able to operate on the turbine changing its set-point of electrical load or turbine outlet temperature). So, the software is operated to control plant properties to generate the effect of a real SOFC in the rig. In stand-alone mode the turbine load is changed with the objective of matching the measured Turbine Outlet Temperature (TOT) value with the calculated one by the model. In grid-connected mode the software/hardware matching is obtained through a direct manipulation of the TOT set-point. This approach was essential to analyze the matching issues between the SOFC and the micro gas turbine devoting several tests on critical operations, such as start-up, shutdown and load changes. Special attention was focused on tests carried out to solve the control system issues for the entire real hybrid plant emulated with this HIL approach. Hence, the innovative control strategies were developed and successfully tested considering both the Proportional Integral Derivative and advanced approaches. Thanks to the experimental tests carried out with this HIL system, a comparison between different control strategies was performed including a statistic analysis on the results The positive performance obtainable with a Model Predictive Control based technique was shown and discussed. So, the HIL system presented in this paper was essential to perform the experimental tests successfully (for real hybrid system development) without the risks of destroying the stack in case of failures. Mainly surge (especially during transient operations, such as load changes) and other critical conditions (e.g. carbon deposition, high pressure difference between the fuel cell sides, high thermal gradients in the stack, excessive thermal stress in the SOFC system components, etc.) have to be carefully avoided in complete plants.

Model-Based Design and Hardware-in-the-Loop Simulation of Engine Lean Operation

2014 ◽  
Author(s):  
Pushkar Agashe ◽  
Yang Li ◽  
Bo Chen
Keyword(s):  
Gasoline Engine ◽  
Control Strategies ◽  
Electronic Control Unit ◽  
Control Unit ◽  
Simulation Models ◽  
Operating Conditions ◽  
Hardware In The Loop ◽  
Vehicle Performance ◽  
Model Based ◽  
Hil Simulation

This paper presents model-based design and hardware-in-the-loop (HIL) simulation of engine lean operation. The functionalities of the homogeneous combustion subsystem in engine Electronic Control Unit (ECU) in dSPACE Automotive Simulation Models (ASM) are first analyzed. To control the gasoline engine in lean operation without the drop of output torque, the combustion subsystem in engine ECU is modified by introducing two control loops, torque modifier and fuel multiplier. The performance of these two controllers is evaluated by HIL simulation using a dSPACE HIL simulator. The HIL simulation models, including vehicle plant model and softECUs in HIL simulator and engine lean control model in hardware engine ECU are modeled using model-based design. With HIL simulation, the designed engine control strategies can be immediately tested to evaluate the overall vehicle performance. The HIL simulation results show that the designed lean combustion control strategy can reduce fuel consumption and is able to meet the torque requirement at lean engine operating conditions.

Sign in / Sign up

Export Citation Format

Share Document