Optimization of Specific Cutting Energy in Turning of AISI 304 Stainless Steel Using Taguchi Method

2021 ◽  
pp. 295-303
Author(s):  
S. Annamalai ◽  
B. Guruprasad ◽  
N. Vaithianathan
Keyword(s):  
Stainless Steel ◽  
Taguchi Method ◽  
304 Stainless Steel ◽  
Specific Cutting Energy ◽  
Aisi 304 Stainless Steel ◽  
Aisi 304 ◽  
Cutting Energy

Optimization of flank wear and surface roughness during turning of AISI 304 stainless steel using the Taguchi method

2020 ◽  
Vol 62 (9) ◽  
pp. 957-961
Author(s):  
Nursel Altan Özbek ◽  
Metin İbrahim Karadag ◽  
Onur Özbek
Keyword(s):  
Surface Roughness ◽  
Stainless Steel ◽  
Taguchi Method ◽  
Feed Rate ◽  
Flank Wear ◽  
Signal To Noise Ratio ◽  
Cutting Speed ◽  
304 Stainless Steel ◽  
Aisi 304 Stainless Steel ◽  
Aisi 304

Abstract This paper presents the effect of cutting tool, cutting speed and feed rate on the flank wear and surface roughness of austenitic stainless steel (AISI 304) during wet turning. Turning tests were designed based on the Taguchi method (L18). An orthogonal array, the signal-to-noise ratio (S/N) and the ANOVA were used to investigate the machinability of AISI 304 stainless steel with PVD and CVD coated tungsten carbide inserts. As a result of ANOVA, it was found that the feed rate was the most effective parameter on both flank wear and surface roughness.

Optimization of flank wear and surface roughness during turning of AISI 304 stainless steel using the Taguchi method

2020 ◽  
Vol 62 (9) ◽  
pp. 957-961
Author(s):  
Nursel Altan Özbek ◽  
Metin İbrahim Karadag ◽  
Onur Özbek
Keyword(s):  
Surface Roughness ◽  
Stainless Steel ◽  
Taguchi Method ◽  
Flank Wear ◽  
304 Stainless Steel ◽  
Aisi 304 Stainless Steel ◽  
Aisi 304

Comparison of Recovery and Recrystallization in Stainless Steel Following Plane-Wave Shock Loading and Explosive Forming

1970 ◽  
Vol 28 ◽  
pp. 428-429 ◽  
Author(s):  
J. A. Korbonski ◽  
L. E. Murr
Keyword(s):  
Stainless Steel ◽  
Shock Loading ◽  
Pressure Pulse ◽  
Shock Pressure ◽  
304 Stainless Steel ◽  
Strain Rates ◽  
Two Dimensional ◽  
Aisi 304 Stainless Steel ◽  
Aisi 304 ◽  
Explosive Forming

Comparison of recovery rates in materials deformed by a unidimensional and two dimensional strains at strain rates in excess of 104 sec.−1 was performed on AISI 304 Stainless Steel. A number of unidirectionally strained foil samples were deformed by shock waves at graduated pressure levels as described by Murr and Grace. The two dimensionally strained foil samples were obtained from radially expanded cylinders by a constant shock pressure pulse and graduated strain as described by Foitz, et al.

Sign in / Sign up

Export Citation Format

Share Document