Effect of agglomerates in ZrO2 powder compacts on microstructural development

1993 ◽  
Vol 28 (2) ◽  
pp. 342-348 ◽  
Author(s):  
J. L. Shi ◽  
J. H. Gao ◽  
Z. X. Lin ◽  
D. S. Yan
Keyword(s):  
Microstructural Development ◽  
Zro2 Powder ◽  
Powder Compacts

Microstructural Development in Nb-Ti Multifilamentary Superconductors During Processing

1985 ◽  
Vol 43 ◽  
pp. 190-191
Author(s):  
A. W. West
Keyword(s):  
Heat Treatment ◽  
Critical Current Density ◽  
Copper Matrix ◽  
Wire Drawing ◽  
Heat Treatments ◽  
Microstructural Development ◽  
Final Size ◽  
Density Values ◽  
The Wire ◽  
Multifilamentary Superconductors

The influence of the filament microstructure on the critical current density values, Jc, of Nb-Ti multifilamentary superconducting composites has been well documented. However the development of these microstructures during composite processing is still under investigation.During manufacture, the multifilamentary composite is given several heat treatments interspersed in the wire-drawing schedule. Typically, these heat treatments are for 5 to 80 hours at temperatures between 523 and 573K. A short heat treatment of approximately 3 hours at 573K is usually given to the wire at final size. Originally this heat treatment was given to soften the copper matrix, but recent work has shown that it can markedly change both the Jc value and microstructure of the composite.

Amorphous silica coating on α-alumina particles

1995 ◽  
Vol 53 ◽  
pp. 210-211
Author(s):  
J. W. Mellowes ◽  
C. M. Chun ◽  
I. A. Aksay
Keyword(s):  
Amorphous Silica ◽  
Heterogeneous Nucleation ◽  
Homogeneous Nucleation ◽  
Silica Coating ◽  
Full Density ◽  
Optimal Conditions ◽  
Fine Grained ◽  
Alumina Particles ◽  
Complete Mullitization ◽  
Powder Compacts

Mullite (3Al2O32SiO2) can be fabricated by transient viscous sintering using composite particles which consist of inner cores of a-alumina and outer coatings of amorphous silica. Powder compacts prepared with these particles are sintered to almost full density at relatively low temperatures (~1300°C) and converted to dense, fine-grained mullite at higher temperatures (>1500°C) by reaction between the alumina core and the silica coating. In order to achieve complete mullitization, optimal conditions for coating alumina particles with amorphous silica must be achieved. Formation of amorphous silica can occur in solution (homogeneous nucleation) or on the surface of alumina (heterogeneous nucleation) depending on the degree of supersaturation of the solvent in which the particles are immersed. Successful coating of silica on alumina occurs when heterogeneous nucleation is promoted and homogeneous nucleation is suppressed. Therefore, one key to successful coating is an understanding of the factors such as pH and concentration that control silica nucleation in aqueous solutions. In the current work, we use TEM to determine the optimal conditions of this processing.

Processing and characterization of YBa2Cu3O7−x/Ag composites

1990 ◽  
Vol 48 (4) ◽  
pp. 46-47
Author(s):  
Jafar Javadpour ◽  
Bradley L. Thiel ◽  
Sarikaya Mehmet ◽  
Ilhan A. Aksay
Keyword(s):  
Composite System ◽  
Precursor Solution ◽  
Microstructural Development ◽  
Superconducting Properties ◽  
Practical Applications ◽  
Nitrate Precursor ◽  
Cold Pressed ◽  
Tape Cast ◽  
Composite Samples

Practical applications of bulk YBa2Cu3O7−x materials have been limited because of their inadequate critical current density (jc) and poor mechanical properties. Several recent reports have indicated that the addition of Ag to the YBa2Cu3O7−x system is beneficial in improving both mechanical and superconducting properties. However, detailed studies concerning the effect of Ag on the microstructural development of the cermet system have been lacking. Here, we present some observations on the microstructural evolution in the YBa2Cu3O7−x/Ag composite system.The composite samples were prepared by mixing various amounts (2.5 - 50 wt%) AgNO3 in the YBa2Cu3O7−x nitrate precursor solution. These solutions were then spray dried and the resulting powders were either cold pressed or tape cast. The microstructures of the sintered samples were analyzed using SEM (Philips 515) and an analytical TEM (Philips 430T).The SEM micrographs of the compacts with 2.5 and 50 wt% Ag addition sintered at 915°C (below the melting point of Ag) for 1 h in air are displayed in Figs. 1 and 2, respectively.

Microstructural control of pitch matrix carbon-carbon composite by iodine treatment

1998 ◽  
Vol 13 (2) ◽  
pp. 302-307 ◽  
Author(s):  
H. Kajiura ◽  
Y. Tanabe ◽  
E. Yasuda ◽  
A. Kaiho ◽  
I. Shiota ◽  
...  
Keyword(s):  
Coal Tar ◽  
Carbon Composite ◽  
Coal Tar Pitch ◽  
Microstructural Development ◽  
Carbon Yield ◽  
Graphitic Structure ◽  
Matrix Microstructure ◽  
Iodine Treatment ◽  
Matrix Precursor ◽  
Microstructural Control

Matrix microstructure of a pitch-based carbon-carbon composite was controlled by an iodine treatment. Coal-tar pitch having the softening point of 101 °C was used as a matrix precursor. The iodine treatment was carried out on a pitch-impregnated specimen at 90 °C for 3–20 h. The specimen was carbonized at 800 °C and graphitized at 2000–3000 °C. The carbon yield increased from 73% to 93% by the iodine treatment. Microstructures of carbonized specimens changed from a flow type texture to a mosaic type one by the iodine treatment. The microstructural development to graphitic structure was suppressed by the iodine treatment.

scholarly journals Sintering of bimodal micrometre/nanometre iron powder compacts - A master sintering curve approach

2021 ◽  
Author(s):  
Swathi K. Manchili ◽  
Johan Wendel ◽  
Eduard Hryha ◽  
Lars Nyborg
Keyword(s):  
Iron Powder ◽  
Powder Compacts
Sign in / Sign up

Export Citation Format

Share Document