Effect of thermomechanical treatment on the mechanical properties of low-carbon and low-alloy steels

1966 ◽  
Vol 8 (9) ◽  
pp. 709-712 ◽  
Author(s):  
M. V. Pridantsev ◽  
�. M. Kotik
Keyword(s):  
Mechanical Properties ◽  
Thermomechanical Treatment ◽  
Low Alloy Steels ◽  
Low Carbon ◽  
Alloy Steels

scholarly journals Study on Spheroidization and Related Heat Treatments of Medium Carbon Alloy Steels

2018 ◽  
Vol 144 ◽  
pp. 02008 ◽  
Author(s):  
S. R. Harisha ◽  
Sathyashankara Sharma ◽  
U. Achutha Kini ◽  
M. C. Gowri Shankar
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Manganese Content ◽  
Heat Treatments ◽  
Carbon Steels ◽  
Low Alloy Steels ◽  
Low Carbon ◽  
Medium Carbon ◽  
Medium Carbon Steels ◽  
Alloy Steels

The importance of medium carbon steels as engineering materials is reflected by the fact that out of the vast majority of engineering grade ferrous alloys available and used in the market today, a large proportion of them are from the family of medium carbon steels. Typically medium carbon steels have a carbon range of 0.25 to 0.65% by weight, and a manganese content ranging from 0.060 to 1.65% by weight. Medium carbon steels are more resistive to cutting, welding and forming as compared to low carbon steels. From the last two decades a number of research scholars reported the use of verity of heat treatments to tailor the properties of medium carbon steels. Spheroidizing is the novel industrial heat treatment employed to improve formability and machinability of medium/high carbon low alloy steels. This exclusive study covers procedure, the effects and possible outcomes of various heat treatments on medium carbon steels. In the present work, other related heat treatments like annealing and special treatments for property alterations which serve as pretreatments for spheroidizing are also reviewed. Medium carbon steels with property alterations by various heat treatment processes are finding increased responsiveness in transportation, aerospace, space, underwater along with other variegated fields. Improved tribological and mechanical properties consisting of impact resistance, stiffness, abrasion and strength are the main reasons for the increased attention of these steels in various industries. In the present scenario for the consolidation of important aspects of various heat treatments and effects on mechanical properties of medium carbons steel, a review of different research papers has been attempted. This review may be used as a guide to provide practical data for heat treatment industry, especially as a tool to enhance workability and tool life.

Effects of cooling rate on the mechanical properties of dual phase treated vanadium steels

1983 ◽  
Vol 41 ◽  
pp. 220-221
Author(s):  
L.J. Chen ◽  
H.C. Cheng ◽  
J.R. Gong ◽  
J.G. Yang
Keyword(s):  
Mechanical Properties ◽  
Cooling Rate ◽  
Automobile Industry ◽  
High Strength ◽  
Weight Percent ◽  
Low Alloy Steels ◽  
Dual Phase ◽  
Resource Requirement ◽  
Alloy Steels ◽  
Potential Weight

For fuel savings as well as energy and resource requirement, high strength low alloy steels (HSLA) are of particular interest to automobile industry because of the potential weight reduction which can be achieved by using thinner section of these steels to carry the same load and thus to improve the fuel mileage. Dual phase treatment has been utilized to obtain superior strength and ductility combinations compared to the HSLA of identical composition. Recently, cooling rate following heat treatment was found to be important to the tensile properties of the dual phase steels. In this paper, we report the results of the investigation of cooling rate on the microstructures and mechanical properties of several vanadium HSLA steels.The steels with composition (in weight percent) listed below were supplied by China Steel Corporation: 1. low V steel (0.11C, 0.65Si, 1.63Mn, 0.015P, 0.008S, 0.084Aℓ, 0.004V), 2. 0.059V steel (0.13C, 0.62S1, 1.59Mn, 0.012P, 0.008S, 0.065Aℓ, 0.059V), 3. 0.10V steel (0.11C, 0.58Si, 1.58Mn, 0.017P, 0.008S, 0.068Aℓ, 0.10V).

MECHANICAL PROPERTIES OF SINTER/FORGED LOW-ALLOY STEELS

1970 ◽  
Vol 13 (26) ◽  
pp. 165-194 ◽  
Author(s):  
R. T. CUNDILL ◽  
E. MARSH ◽  
K. A. RIDAL
Keyword(s):  
Mechanical Properties ◽  
Low Alloy Steels ◽  
Alloy Steels

Recent Aspects on the Effect of Inclusion Characteristics on the Intragranular Ferrite Formation in Low Alloy Steels: A Review

2017 ◽  
Vol 36 (4) ◽  
pp. 309-325 ◽  
Author(s):  
Wangzhong Mu ◽  
Pär Göran Jönsson ◽  
Keiji Nakajima
Keyword(s):  
Heat Affected Zone ◽  
Low Alloy Steels ◽  
Low Carbon ◽  
Intragranular Ferrite ◽  
Metallic Inclusions ◽  
Theoretical Investigations ◽  
Alloy Steels ◽  
Institute Of Technology ◽  
Future Work

AbstractIntragranular ferrite (IGF), which nucleates from specific inclusion surfaces in low alloy steels, is the desired microstructure to improve mechanical properties of steel such as the toughness. This microstructure is especially important in the coarse grain heat affected zone (CGHAZ) of weldments. The latest review paper focusing on the role of non-metallic inclusions in the IGF formation in steels has been reported by Sarma et al. in 2009 (ISIJ int., 49(2009), 1063–1074). In recent years, large amount of papers have been presented to investigate different issues of this topic. This paper mainly highlights the frontiers of experimental and theoretical investigations on the effects of inclusion characteristics, such as the composition, size distribution and number density, on the IGF formation in low carbon low-alloyed steels, undertaken by the group of Applied Process Metallurgy, KTH Royal Institute of Technology. Related results reported in previous studies are also introduced. Also, plausible future work regarding various items of IGF formation is mentioned in each section. This work aims to give a better control of improving the steel quality during casting and in the heat affected zone (HAZ) of weldment, according to the concept of oxide metallurgy.

Sign in / Sign up

Export Citation Format

Share Document