Action of a moving load on a nonlinearly compressed plastic strip with a deformable base

1991 ◽  
Vol 31 (3) ◽  
pp. 474-481
Author(s):  
K. Atabaev ◽  
N. Mamadaliev ◽  
N. Turaev
Keyword(s):  
Moving Load ◽  
Plastic Strip ◽  
Deformable Base

MODELING OF THE STRESS-STRAIN STATE OF A TRANSPORT TUNNEL UNDER LOAD AS A MEASURE TO REDUCE OPERATIONAL RISKS TO TRANSPORTATION FACILITIES

2020 ◽  
Vol 3 (8) ◽  
pp. 28-34
Author(s):  
N. V. IVANITSKAYA ◽  
◽  
A. K. BAYBULOV ◽  
M. V. SAFRONCHUK ◽  
◽  
...  
Keyword(s):  
Strain State ◽  
Moving Load ◽  
Element Model ◽  
Transport Infrastructure ◽  
Design Stage ◽  
Surface Load ◽  
Stress Strain ◽  
Stress Strain State ◽  
Operational Risks ◽  
Von Mises

In many countries economic policy has been paying increasing attention to the modernization and development of transport infrastructure as a measure of macroeconomic stimulation. Tunnels as an important component of transport infrastructure save a lot of logistical costs. It stimulates increasing freight and passenger traffic as well as the risks of the consequences of unforeseen overloads. The objective of the paper is to suggest the way to reduce operational risks of unforeseen moving load by modeling of the stress-strain state of a transport tunnel under growing load for different conditions and geophysical parameters. The article presents the results of a study of the stress-strain state (SSS) of a transport tunnel exposed to a mobile surface load. Numerical experiments carried out in the ANSYS software package made it possible to obtain diagrams showing the distribution of equivalent stresses (von Mises – stresses) according to the finite element model of the tunnel. The research results give grounds to assert that from external factors the stress state of the tunnel is mainly influenced by the distance to the moving load. The results obtained make it possible to predict in advance the parameters of the stress-strain state in the near-contour area of the tunnel and use the results in the subsequent design of underground facilities, as well as to increase their reliability and operational safety. This investigation gives an opportunity not only to reduce operational risks at the design stage, but to choose an optimal balance between investigation costs and benefits of safety usage period prolongation.

Nonlocal stress analysis of an irregular FGFPM structure imperfectly bonded to fiber-reinforced substrate subjected to moving load

2021 ◽  
Vol 147 ◽  
pp. 106744
Author(s):  
Shishir Gupta ◽  
Soumik Das ◽  
Rachaita Dutta
Keyword(s):  
Stress Analysis ◽  
Moving Load ◽  
Fiber Reinforced ◽  
Nonlocal Stress

scholarly journals Coupled bending and torsional beam vibrations excited by a moving load

PAMM ◽  
2021 ◽  
Vol 20 (1) ◽  
Author(s):  
Helmut J. Holl ◽  
Lukas Keplinger
Keyword(s):  
Moving Load ◽  
Torsional Beam

Dynamic response of double-FG porous beam system subjected to moving load

2021 ◽  
Author(s):  
Shujia Chen ◽  
Qiao Zhang ◽  
Hu Liu
Keyword(s):  
Dynamic Response ◽  
Moving Load ◽  
Beam System

Asymptotic derivation of a refined equation for an elastic beam resting on a Winkler foundation

2021 ◽  
pp. 108128652110238
Author(s):  
Barış Erbaş ◽  
Julius Kaplunov ◽  
Isaac Elishakoff
Keyword(s):  
Ad Hoc ◽  
Moving Load ◽  
Low Frequency ◽  
Elastic Beam ◽  
Winkler Foundation ◽  
One Dimensional ◽  
Beam Equations ◽  
Dimensional Equation ◽  
Phase And Group Velocities ◽  
Group Velocities

A two-dimensional mixed problem for a thin elastic strip resting on a Winkler foundation is considered within the framework of plane stress setup. The relative stiffness of the foundation is supposed to be small to ensure low-frequency vibrations. Asymptotic analysis at a higher order results in a one-dimensional equation of bending motion refining numerous ad hoc developments starting from Timoshenko-type beam equations. Two-term expansions through the foundation stiffness are presented for phase and group velocities, as well as for the critical velocity of a moving load. In addition, the formula for the longitudinal displacements of the beam due to its transverse compression is derived.

Dynamic analysis of an arch due to a moving load

2004 ◽  
Vol 269 (3-5) ◽  
pp. 511-534 ◽  
Author(s):  
Jong-Shyong Wu ◽  
Lieh-Kwang Chiang
Keyword(s):  
Dynamic Analysis ◽  
Moving Load

The Calculation of the Supporting Stress of Track Plate in Ballastless High-Speed Rail Structure

2011 ◽  
Vol 97-98 ◽  
pp. 3-9
Author(s):  
Yang Wang ◽  
Quan Mei Gong ◽  
Mei Fang Li
Keyword(s):  
Stress Distribution ◽  
High Speed ◽  
Design Theory ◽  
Moving Load ◽  
Structure Design ◽  
Track Structure ◽  
Beam Model ◽  
High Speed Rail ◽  
Slab Track ◽  
Ballastless Track

The slab track is a new sort of track structure, which has been widely used in high-speed rail and special line for passenger. However, the ballastless track structure design theory is still not perfect and can not meet the requirements of current high-speed rail and passenger line ballastless track. In this paper, composite beam method is used to calculate the deflection of the track plate and in this way the vertical supporting stress distribution of the track plate can be gotten which set a basis for the follow-up study of the dynamic stress distribution in the subgrade. Slab track plate’s bearing stress under moving load is analyzed through Matlab program. By calculation and analysis, it is found that the deflection of track plate and the rail in the double-point-supported finite beam model refers to the rate of spring coefficient of the fastener and the mortar.The supporting stress of the rail plate is inversely proportional to the supporting stress of the rail. The two boundary conditions of that model ,namely, setting the end of the model in the seams of the track plate or not , have little effect on the results. We can use the supporting stress of the track plates on state 1to get the distribution of the supporting stress in the track plate when bogies pass. Also, when the dynamic load magnification factor is 1.2, the track plate supporting stress of CRST I & CRST II-plate non-ballasted structure is around 40kPa.

Sign in / Sign up

Export Citation Format

Share Document