Investigation of the bending fatigue strength of certain alloys with stress concentration

1974 ◽  
Vol 6 (7) ◽  
pp. 798-804 ◽  
Author(s):  
V. T. Troshchenko ◽  
A. F. Getman
Keyword(s):  
Fatigue Strength ◽  
Stress Concentration ◽  
Bending Fatigue ◽  
Bending Fatigue Strength

Bending Fatigue Strength Evaluation of Notched Structural Steel Sheet Repaired by Bolt

2010 ◽  
Vol 452-453 ◽  
pp. 25-28
Author(s):  
Li Sha He ◽  
Nobusuke Hattori
Keyword(s):  
Plastic Deformation ◽  
Fatigue Strength ◽  
Stress Concentration ◽  
Structural Steel ◽  
Fatigue Limit ◽  
Steel Sheet ◽  
Bending Fatigue ◽  
Steel Sheets ◽  
Bending Fatigue Strength ◽  
Working Method

The present investigation attempts to evaluate the improvement of working by bolt on the fatigue limit of structural steel sheets with drilling a circular hole. The material used in this study is structural steel (JIS SM400A). And the specimens are identified to two types of the non-worked specimen and the worked specimen. The results obtained in this study can be summarized as follows: (1) The fatigue limit of worked specimens increases than that of non-worked specimen. Futhermore, there has a suitable value of the torque for improving the fatigue limits. (2) The reasons of enhancing the fatigue strength of the worked specimens are due to the elastic deformation, the plastic deformation and the changing of stress concentration part. Our investigations confirm the advantages of this working method which repaired the structural steel sheets by bolt.

scholarly journals On the determination of the bending fatigue strength in and above the very high cycle fatigue regime of shot-peened gears

2021 ◽  
Author(s):  
D. Fuchs ◽  
S. Schurer ◽  
T. Tobie ◽  
K. Stahl
Keyword(s):  
Fatigue Strength ◽  
High Cycle Fatigue ◽  
Load Carrying Capacity ◽  
Cycle Fatigue ◽  
Bending Fatigue ◽  
Very High Cycle Fatigue ◽  
Bending Load ◽  
Load Carrying ◽  
Bending Fatigue Strength ◽  
Very High

AbstractDemands on modern gearboxes are constantly increasing, for example to comply with lightweight design goals or new CO2 thresholds. Normally, to increase performance requires making gearboxes and powertrains more robust. However, this increases the weight of a standard gearbox. The two trends therefore seem contradictory. To satisfy both of these goals, gears in gearboxes can be shot-peened to introduce high compressive residual stresses and improve their bending fatigue strength. To determine a gear’s tooth root bending fatigue strength, experiments are conducted up to a defined number of load cycles in the high cycle fatigue range. However, investigations of shot-peened gears have revealed tooth root fracture damage initiated at non-metallic inclusions in and above the very high cycle fatigue range. This means that a further reduction in bending load carrying capacity has to be expected at higher load cycles, something which is not covered under current standard testing conditions. The question is whether there is a significant decrease in the bending load carrying capacity and, also, if pulsating tests conducted at higher load cycles—or even tests on the FZG back-to-back test rig—are necessary to determine a proper endurance fatigue limit for shot-peened gears. This paper examines these questions.

Investigating Fatigue Strength of Vacuum Carburized 17CrNi6-6 Steel Using a Resonance High Frequency Method

2014 ◽  
Vol 225 ◽  
pp. 45-52 ◽  
Author(s):  
Piotr Kula ◽  
Konrad Dybowski ◽  
Sebastian Lipa ◽  
Robert Pietrasik ◽  
Radomir Atraszkiewicz ◽  
...  
Keyword(s):  
High Pressure ◽  
Fatigue Strength ◽  
High Frequency ◽  
Vacuum Carburizing ◽  
Frequency Method ◽  
Single Degree Of Freedom ◽  
Bending Fatigue ◽  
Single Degree ◽  
Bending Fatigue Strength ◽  
Frequency Changes

The bending fatigue strength of 17CrNi6-6 steel subjected to vacuum carburizing with high pressure gas hardening has been measured using a novel high-frequency technique. The test records the changes in resonance and consists of observing resonance frequency changes in a vibrating system with a single degree of freedom as a result of the forming of a fatigue crack. Moreover, a mechanism of fatigue nucleation and propagation in steel hardened by vacuum carburizing is presented.

Bending fatigue strength and impact strength of spur gears with various surface hardening treatments

2021 ◽  
Vol 2021.59 (0) ◽  
pp. 05a1
Author(s):  
Ryo ASAKURA ◽  
Kohei HIBI ◽  
Kenichi SAKAMOTO ◽  
Toshiyasu OMURA ◽  
Ryosuke NISHI ◽  
...  
Keyword(s):  
Fatigue Strength ◽  
Impact Strength ◽  
Surface Hardening ◽  
Spur Gears ◽  
Bending Fatigue ◽  
Bending Fatigue Strength

High Cycle Fatigue Behavior of Thermally Oxidized Ti6Al4V Alloy

2007 ◽  
Vol 561-565 ◽  
pp. 2179-2182 ◽  
Author(s):  
Mehmet Cingi ◽  
Onur Meydanoglu ◽  
Hasan Guleryuz ◽  
Murat Baydogan ◽  
Huseyin Cimenoglu ◽  
...  
Keyword(s):  
Fatigue Strength ◽  
Yield Strength ◽  
Thermal Oxidation ◽  
Fatigue Behavior ◽  
Surface Hardness ◽  
Ti6al4v Alloy ◽  
Bending Fatigue ◽  
Rotating Bending Fatigue ◽  
Rotating Bending ◽  
Bending Fatigue Strength

In this study, the effect of thermal oxidation on the high cycle rotating bending fatigue behavior of Ti6Al4V alloy was investigated. Oxidation, which was performed at 600°C for 60 h in air, considerably improved the surface hardness and particularly the yield strength of the alloy without scarifying the tensile ductility. Unfortunately, the rotating bending fatigue strength at 5x106 cycles decreased from about 610 MPa to about 400 MPa upon oxidation. Thus, thermal oxidation leaded a reduction in the fatigue strength of around 34%, while improving the surface hardness (HV0.1) and yield strength 85 % and 36 %, respectively.

Sign in / Sign up

Export Citation Format

Share Document