scholarly journals Correction to: Multiscale mixed hydrodynamics in line contacts

2021 ◽  
Author(s):  
Yongbin Zhang
Keyword(s):  
Line Contacts

The behaviour of heavily loaded line contacts with transverse roughness

1999 ◽  
Vol 213 (4) ◽  
pp. 309-320 ◽  
Author(s):  
C. J. Hooke
Keyword(s):  
Surface Roughness ◽  
Full Range ◽  
Numerical Results ◽  
Operating Conditions ◽  
Entrainment Velocity ◽  
Original Surface ◽  
Line Contacts ◽  
Transverse Roughness ◽  
Inlet Length

In heavily loaded, piezoviscous contacts the surface roughness tends to be flattened inside the conjunction by any relative sliding of the surfaces. However, before it is flattened, the roughness affects the inlet to the contact, producing clearance variations there. These variations are then convected through the contact, at the entrainment velocity, producing a clearance distribution that differs from the original surface. The present paper explores this behaviour and establishes how the amplitude of the convected clearance varies with wavelength and operating conditions. It is shown that the primary influence is the ratio of the wavelength to the inlet length of the conjunction. Where this ratio is large, the roughness is smoothed and there is little variation in clearance under the conjunction. Where the ratio is small, significant variations in clearance may occur but the precise amplitude and phasing depend on the ratio of slide to roll velocities and on the value of a piezoviscous parameter, c. The numerical results agree closely with existing solutions but extend these to cover the full range of operating conditions.

A Complete Solution for Thermal-Elastohydrodynamic Lubrication of Line Contacts Using Circular Non-Newtonian Fluid Model

1992 ◽  
Vol 114 (3) ◽  
pp. 540-551 ◽  
Author(s):  
Hsing-Sen S. Hsiao ◽  
Bernard J. Hamrock
Keyword(s):  
Boundary Conditions ◽  
Newtonian Fluid ◽  
Energy Equation ◽  
Control Volume ◽  
Fluid Model ◽  
Complete Solution ◽  
Circular Model ◽  
Line Contacts ◽  
Stress Boundary Conditions ◽  
Stress Boundary

A complete solution is obtained for elastohydrodynamically lubricated conjunctions in line contacts considering the effects of temperature and the non-Newtonian characteristics of lubricants with limiting shear strength. The complete fast approach is used to solve the thermal Reynolds equation by using the complete circular non-Newtonian fluid model and considering both velocity and stress boundary conditions. The reason and the occasion to incorporate stress boundary conditions for the circular model are discussed. A conservative form of the energy equation is developed by using the finite control volume approach. Analytical solutions for solid surface temperatures that consider two-dimensional heat flow within the solids are used. A straightforward finite difference method, successive over-relaxation by lines, is employed to solve the energy equation. Results of thermal effects on film shape, pressure profile, streamlines, and friction coefficient are presented.

Simple Formulas for Performance Parameters Used in Elastohydrodynamically Lubricated Line Contacts

1989 ◽  
Vol 111 (2) ◽  
pp. 246-251 ◽  
Author(s):  
Ping Pan ◽  
B. J. Hamrock
Keyword(s):  
Film Thickness ◽  
Curve Fitting ◽  
Center Of Pressure ◽  
Operating Parameters ◽  
Performance Parameters ◽  
Practical Applications ◽  
Line Contacts ◽  
Pressure Spike

The film thickness and pressure in elastohydrodynamically lubricated conjunctions have been evaluated numerically for a rather complete range of operating parameters (dimensionless load, speed, and materials parameters) normally experienced in practical applications. From the film thickness and pressure throughout the conjunction a number of performance parameters were evaluated. By curve fitting the data, formulas were obtained that allow easy evaluation of the amplitude and location of the pressure spike, the minimum and central film thicknesses, the value of ρeHe, and the center of pressure.

Simulation of Plasto-Elastohydrodynamic Lubrication in Line Contacts of Infinite and Finite Length

2015 ◽  
Vol 137 (4) ◽  
Author(s):  
Tao He ◽  
Jiaxu Wang ◽  
Zhanjiang Wang ◽  
Dong Zhu
Keyword(s):  
Surface Roughness ◽  
Finite Length ◽  
3D Model ◽  
Three Dimensional ◽  
Elastohydrodynamic Lubrication ◽  
Axial Direction ◽  
Contact Length ◽  
Line Contact ◽  
Line Contacts ◽  
3D Surface Topography

Line contact is common in many machine components, such as various gears, roller and needle bearings, and cams and followers. Traditionally, line contact is modeled as a two-dimensional (2D) problem when the surfaces are assumed to be smooth or treated stochastically. In reality, however, surface roughness is usually three-dimensional (3D) in nature, so that a 3D model is needed when analyzing contact and lubrication deterministically. Moreover, contact length is often finite, and realistic geometry may possibly include a crowning in the axial direction and round corners or chamfers at two ends. In the present study, plasto-elastohydrodynamic lubrication (PEHL) simulations for line contacts of both infinite and finite length have been conducted, taking into account the effects of surface roughness and possible plastic deformation, with a 3D model that is needed when taking into account the realistic contact geometry and the 3D surface topography. With this newly developed PEHL model, numerical cases are analyzed in order to reveal the PEHL characteristics in different types of line contact.

Elastohydrodynamic Lubrication of Finite Line Contacts

1983 ◽  
Vol 105 (4) ◽  
pp. 598-604 ◽  
Author(s):  
A. Mostofi ◽  
R. Gohar
Keyword(s):  
Elastohydrodynamic Lubrication ◽  
Mineral Oil ◽  
Pressure Variation ◽  
Material Parameters ◽  
Line Contacts ◽  
Finite Line ◽  
Moderate Load ◽  
Infinite Line ◽  
Cylindrical Roller ◽  
Theoretical Results

In this paper, a numerical solution to the elastohydrodynamic lubrication (EHL) problem is presented for a cylindrical roller with axially profiled ends, rolling over a flat plane. Convergence was obtained for moderate load and material parameters (glass, steel, and a mineral oil). Isobars, contours, and section graphs, show pressure variation and film shape. Predictions of film thickness compare favorably with experiments which use the optical interference method, as well as with other theoretical results for an infinite line contact, or an ellipse having a long slender aspect ratio. The maximum EHL pressure occurs near the start of the profiling and can exceed pressure concentrations there predicted by elastostatic theory.

Sign in / Sign up

Export Citation Format

Share Document