The effect of tool material grain size on the machining process in ball end milling

2020 ◽  
Vol 106 (9-10) ◽  
pp. 4411-4421
Author(s):  
Farooq Ahmed ◽  
Tae Jo Ko ◽  
Jongmin Lee ◽  
Yein Kwak ◽  
Rendi Kurniawan
Keyword(s):  
Grain Size ◽  
End Milling ◽  
Tool Material ◽  
Machining Process ◽  
Ball End Milling ◽  
Material Grain Size

Research on Feedrate Optimization Based on Cutting Force Model with Double Effect for the Ball-End Milling

2011 ◽  
Vol 291-294 ◽  
pp. 2965-2969
Author(s):  
Yu Jun Cai ◽  
Hua Shen ◽  
Tie Li Qi
Keyword(s):  
Cutting Force ◽  
End Milling ◽  
Double Effect ◽  
Machining Process ◽  
Force Model ◽  
Optimization Strategy ◽  
Cutting Force Model ◽  
Ball End Mill ◽  
Ball End Milling ◽  
Feedrate Optimization

A new cutting force model of ball-end mill with double effect is developed through analysing the machining process by using differential geometry. The cutting force model is needed to be revised for the component force in Z direction because of the offset to the actual results. The cutting force and the ball-end milling force coefficients can be given with numerical method. A feedrate optimization strategy is also proposed based on the developed cutting force model and tested effectively.

scholarly journals Study on the Design and Cutting Performance of a Revolving Cycloid Milling Cutter

2019 ◽  
Vol 9 (14) ◽  
pp. 2915 ◽  
Author(s):  
Guangyue Wang ◽  
Xianli Liu ◽  
Weijie Gao ◽  
Bingxin Yan ◽  
Tao Chen
Keyword(s):  
Titanium Alloy ◽  
End Milling ◽  
Tangential Force ◽  
Boundary Curve ◽  
Cutting Performance ◽  
Machining Process ◽  
Rake Face ◽  
Milling Cutter ◽  
Ball End Milling ◽  
Five Axis

Problems such as low machining efficiency, severe tool wear and difficulty in safeguarding surface quality always exist in the machining process of titanium alloy with ball-end milling cutters. To address these issues, the design and manufacture of a revolving cycloid milling cutter for titanium alloy processing were studied in this paper. Firstly, the mathematical model of the revolving cycloid milling cutter contour surface was established. The parametric equation of an orthogonal helix cutting edge curve of a revolving cycloid milling cutter is presented. Then, the bottom boundary curve of the rake face is introduced. The five-axis grinding trajectory equation of revolving cycloid milling cutter rake face was derived based on the edge curve equation and coordinate transformation. Next, fabricating the revolving cycloid milling cutter and detecting the grinding accuracy of tool profile and geometric angle were performed. At last, a contrast test regarding the performance of the revolving cycloid milling cutter and the ball-end milling cutter in cutting titanium alloy TC11 was carried out. According to the test results, in comparison to the ball-end milling cutter, the revolving cycloid milling cutter had a smaller ratio of the axial force to the tangential force. Moreover, its flank face wore more slowly and evenly. As a result, a good surface processing quality can be maintained even under larger wear conditions, demonstrating an outstanding cutting performance.

scholarly journals The Effect of the Feed Direction on the Micro- and Macro Accuracy of 3D Ball-end Milling of Chromium-Molybdenum Alloy Steel

Materials ◽  
2019 ◽  
Vol 12 (24) ◽  
pp. 4038
Author(s):  
Balázs Mikó ◽  
Bálint Varga ◽  
Wojciech Zębala
Keyword(s):  
Surface Roughness ◽  
Metal Cutting ◽  
Tool Path ◽  
End Milling ◽  
Cutting Parameters ◽  
Machining Process ◽  
Free Form ◽  
Dimensional Error ◽  
Ball End Milling ◽  
Free Form Surfaces

The machining of free form surfaces is one of the most challenging problems in the field of metal cutting technology. The produced part and machining process should satisfy the working, accuracy, and financial requirements. The accuracy can describe dimensional, geometrical, and surface roughness parameters. In the current article, three of them are investigated in the case of the ball-end milling of a convex and concave cylindrical surface form 42CrMo4 steel alloy. The effect of the tool path direction is investigated and the other cutting parameters are constant. The surface roughness and the geometric error are measured by contact methods. Based on the results, the surface roughness, dimensional error, and the geometrical error mean different aspects of the accuracy, but they are not independent from each other. The investigated input parameters have a similar effect on them. The regression analyses result a very good liner regression for geometric errors and shows the importance of surface roughness.

Cutting Force Analysis to Determine the Performance of Micro End Milling Process of Silicon Wafer

2007 ◽  
Author(s):  
Rusnaldy ◽  
Tae Jo Ko ◽  
Hee Sool Kim
Keyword(s):  
Cutting Force ◽  
Silicon Wafer ◽  
Cutting Forces ◽  
End Milling ◽  
Chip Thickness ◽  
Tool Material ◽  
Machining Process ◽  
Tool Geometry ◽  
Machined Surface ◽  
Micro End Milling

There is a lack of fundamental understanding of micro-end-milling of silicon wafer, specifically basic understanding of material removal mechanism, cutting forces and machined surface integrity in micro scale machining of silicon. It is necessary to determine the forces generated during the cutting operation due to chip thickness along with tool geometry, tool material properties and workpiece properties because cutting forces will provide vital information for the design, modeling and control of the machining process. In this study, cutting force data can be used to determine cutting regime machining of silicon wafer.

Parameter Optimization of Ball End Milling Process on Inconel 718 Using RSM and TLBO Algorithm

2015 ◽  
Vol 15 (3) ◽  
pp. 293-300 ◽  
Author(s):  
Nandkumar N. Bhopale ◽  
Nilesh Nikam ◽  
Raju S. Pawade
Keyword(s):  
Surface Roughness ◽  
Response Surface Methodology ◽  
Response Surface ◽  
Surface Integrity ◽  
Inconel 718 ◽  
Tool Path ◽  
End Milling ◽  
Spindle Speed ◽  
Depth Of Cut ◽  
Ball End Milling

AbstractThis paper presents the application of Response Surface Methodology (RSM) coupled with Teaching Learning Based Optimization Technique (TLBO) for optimizing surface integrity of thin cantilever type Inconel 718 workpiece in ball end milling. The machining and tool related parameters like spindle speed, milling feed, axial depth of cut and tool path orientation are optimized with considerations of multiple response like deflection, surface roughness, and micro hardness of plate. Mathematical relationship between process parameters and deflection, surface roughness and microhardness are found out by using response surface methodology. It is observed that after optimizing the process that at the spindle speed of 2,000 rpm, feed 0.05 mm/tooth/rev, plate thickness of 5.5 mm and 15° workpiece inclination with horizontal tool path gives favorable surface integrity.

Mechanistic Modeling of the Ball End Milling Process for Multi-Axis Machining of Free-Form Surfaces

2000 ◽  
Vol 123 (3) ◽  
pp. 369-379 ◽  
Author(s):  
Rixin Zhu ◽  
Shiv G. Kapoor ◽  
Richard E. DeVor
Keyword(s):  
End Milling ◽  
Chip Thickness ◽  
Mechanistic Modeling ◽  
Free Form ◽  
Surface Geometry ◽  
Workpiece Surface ◽  
Ball End Milling ◽  
Modeling Approach ◽  
Free Form Surfaces ◽  
Cutting Point

A mechanistic modeling approach to predicting cutting forces is developed for multi-axis ball end milling of free-form surfaces. The workpiece surface is represented by discretized point vectors. The modeling approach employs the cutting edge profile in either analytical or measured form. The engaged cut geometry is determined by classification of the elemental cutting point positions with respect to the workpiece surface. The chip load model determines the undeformed chip thickness distribution along the cutting edges with consideration of various process faults. Given a 5-axis tool path in a cutter location file, shape driving profiles are generated and piecewise ruled surfaces are used to construct the tool swept envelope. The tool swept envelope is then used to update the workpiece surface geometry employing the Z-map method. A series of 3-axis and 5-axis surface machining tests on Ti6A14V were conducted to validate the model. The model shows good computational efficiency, and the force predictions are found in good agreement with the measured data.

Geometrical Modeling of Tool-Workpiece Contact Zone and Chip Formation in Finish Ball End Milling Process with Tool Inclination Angles

2016 ◽  
Vol 693 ◽  
pp. 788-794
Author(s):  
Xiao Xiao Chen ◽  
Jun Zhao
Keyword(s):  
Contact Zone ◽  
Measurement Method ◽  
End Milling ◽  
Milling Process ◽  
Ball End Milling ◽  
Geometrical Modeling ◽  
Section Area ◽  
Inclination Angles ◽  
Area And Perimeter ◽  
End Milling Process

The tool-workpiece contact zone is an important issue in the ball end milling process. This paper investigated the effects of tool inclination angles on the tool-workpiece contact zone, and variations of the cutting section area and perimeter with the increasing tilt and lead angles were also analyzed by geometrical modeling and measurement method for ball end milling process. The appropriate tool inclination angles, which could avoid the extrusion and friction between tool tip and the uncut materials, shorten the loading time on the cutting flute, and decrease the maximum cutting forces, could be preferentially selected according to the distribution characteristics of the tool-workpiece contact zone and the variations of the cutting section area and perimeter corresponding to various tool postures.

Sign in / Sign up

Export Citation Format

Share Document