Stochastic modeling applications for the prediction of COD removal efficiency of UASB reactors treating diluted real cotton textile wastewater

2007 ◽  
Vol 23 (1) ◽  
pp. 13-26 ◽  
Author(s):  
Kaan Yetilmezsoy ◽  
Zehra Sapci-Zengin
Keyword(s):  
Stochastic Modeling ◽  
Removal Efficiency ◽  
Textile Wastewater ◽  
Cod Removal ◽  
Cotton Textile ◽  
Cod Removal Efficiency ◽  
Uasb Reactors

Textile Wastewater Treatment Using Combined Process of Biological Wriggle Bed and Ozone Biological Aerated Filter

2012 ◽  
Vol 441 ◽  
pp. 589-592
Author(s):  
Zhi Min Fu ◽  
Yu Gao Zhang ◽  
Xiao Jun Wang
Keyword(s):  
Wastewater Treatment ◽  
Removal Efficiency ◽  
Textile Wastewater ◽  
Cod Removal ◽  
Biological Aerated Filter ◽  
Combined Process ◽  
Cod Removal Efficiency ◽  
Aerated Filter ◽  
Textile Wastewater Treatment

A combined process of biological wriggle bed and ozone biological aerated filter was utilized to treat textile wastewater. Results showed that COD removal efficiency was almost 90.4%. The average effluent COD was 85.87 mg/L. The effluent colority was 64-32 times. This study indicated that the combined process is potentially useful for treating textile wastewater.

scholarly journals Treatment of Reactive Dye Containing Textile Wastewater using Microwave Assisted Synthesized Poly(Diallyldimethylammonium Chloride)

2018 ◽  
Vol 41 (2) ◽  
pp. 165-174
Author(s):  
Mahmudur Rahman ◽  
Masud Rana ◽  
Zinia Nasreen ◽  
Md Mainul Hossain ◽  
Ayesha Sharmin
Keyword(s):  
Wastewater Treatment ◽  
Removal Efficiency ◽  
Textile Wastewater ◽  
Reactive Dye ◽  
Cod Removal ◽  
Microwave Assisted ◽  
Diallyldimethylammonium Chloride ◽  
Cod Removal Efficiency ◽  
Textile Wastewater Treatment ◽  
Academy Of Sciences

Results on the applicability of microwave assisted synthesized poly(diallyldimethyl ammonium chloride) (polyDADMAC) in reactive dye containing textile wastewater treatment are reported. Diallyldimethylammonium chloride and poly(diallyldimethylammonium chloride) have been characterized by spectral means. The microwave assisted synthesized polyDADMAC has shown some effectiveness in textile wastewater treatment. COD removal efficiency of actual textile wastewater is below 30% whereas the standard dye sample shows about 50-60% COD removal efficiency. TDS and TSS also decreased after treatment of the wastewater with polyDADMAC.Journal of Bangladesh Academy of Sciences, Vol. 41, No. 2, 165-174, 2017

Two examples of anaerobic pre-treatment of wastewater in the beverage industry

1997 ◽  
Vol 36 (2-3) ◽  
pp. 311-319 ◽  
Author(s):  
Ute Austermann-Haun ◽  
Karl-Heinz Rosenwinkel
Keyword(s):  
Removal Efficiency ◽  
Fruit Juice ◽  
Anaerobic Treatment ◽  
Full Scale ◽  
Cod Removal ◽  
Load Variations ◽  
Cod Removal Efficiency ◽  
Beverage Industry ◽  
Pre Treatment ◽  
Uasb Reactors

Two examples of full scale UASB-reactors in a fruit juice factory and a brewery are given. In both cases, the design was based on semi-technical tests. Although the wastewater concentrations are rather similar and move within a low range, the parts of the anaerobic treatment plants and their design are different. In both cases, the COD removal efficiency in the UASB-reactors is consistently above 80%. It becomes apparent that UASB-reactors are very suitable for industries with seasonal load variations. The co-fermentation of a kieselguhre-sludge-mixture was tested in lab-scale experiments. It became obvious that the pellet structure of the biomass gets lost. Furthermore, it is shown that the running expenses of anaerobic pre-treatment are very low, even when combined with an aerobic stage.

scholarly journals Allochthonous and Autochthonous Halothermotolerant Bioanodes From Hypersaline Sediment and Textile Wastewater: A Promising Microbial Electrochemical Process for Energy Recovery Coupled With Real Textile Wastewater Treatment

2020 ◽  
Vol 8 ◽  
Author(s):  
Refka Askri ◽  
Benjamin Erable ◽  
Luc Etcheverry ◽  
Sirine Saadaoui ◽  
Mohamed Neifar ◽  
...  
Keyword(s):  
Removal Efficiency ◽  
Community Dynamics ◽  
Textile Wastewater ◽  
Electrochemical Process ◽  
Cod Removal ◽  
Simultaneous Treatment ◽  
Cod Removal Efficiency ◽  
Bacterial Community Dynamics ◽  
Current Production ◽  
Autochthonous Bacteria

The textile and clothing industry is the first manufacture sector in Tunisia in terms of employment and number of enterprises. It generates large volumes of textile dyeing wastewater (TDWW) containing high concentrations of saline, alkaline, and recalcitrant pollutants that could fuel tenacious and resilient electrochemically active microorganisms in bioanodes of bioelectrochemical systems. In this study, a designed hybrid bacterial halothermotolerant bioanode incorporating indigenous and exogenous bacteria from both hypersaline sediment of Chott El Djerid (HSCE) and TDWW is proposed for simultaneous treatment of real TDWW and anodic current generation under high salinity. For the proposed halothermotolerant bioanodes, electrical current production, chemical oxygen demand (COD) removal efficiency, and bacterial community dynamics were monitored. All the experiments of halothermotolerant bioanode formation have been conducted on 6 cm2 carbon felt electrodes polarized at −0.1 V/SCE and inoculated with 80% of TDWW and 20% of HSCE for 17 days at 45°C. A reproducible current production of about 12.5 ± 0.2 A/m2 and a total of 91 ± 3% of COD removal efficiency were experimentally validated. Metagenomic analysis demonstrated significant differences in bacterial diversity mainly at species level between anodic biofilms incorporating allochthonous and autochthonous bacteria and anodic biofilm containing only autochthonous bacteria as a control. Therefore, we concluded that these results provide for the first time a new noteworthy alternative for achieving treatment and recover energy, in the form of a high electric current, from real saline TDWW.

The effect of operational conditions on the performance of UASB reactors for domestic wastewater treatment

2005 ◽  
Vol 52 (1-2) ◽  
pp. 299-305 ◽  
Author(s):  
R.C. Leitão ◽  
J.A. Silva-Filho ◽  
W. Sanders ◽  
A.C. van Haandel ◽  
G. Zeeman ◽  
...  
Keyword(s):  
Removal Efficiency ◽  
Municipal Wastewater ◽  
Domestic Wastewater ◽  
Pilot Scale ◽  
Cod Removal ◽  
Upflow Anaerobic Sludge Blanket ◽  
Anaerobic Sludge ◽  
Operational Conditions ◽  
Cod Removal Efficiency ◽  
Uasb Reactors

In this investigation, the performance of Upflow Anaerobic Sludge Blanket (UASB) reactors treating municipal wastewater was evaluated on the basis of: (i) COD removal efficiency, (ii) effluent variability, and (iii) pH stability. The experiments were performed using 8 pilot-scale UASB reactors (120 L) from which some of them were operated with different influent COD (CODInf ranging from 92 to 816 mg/L) and some at different hydraulic retention time (HRT ranging from 1 to 6 h). The results show that decreasing the CODInf, or lowering the HRT, leads to decreased efficiencies and increased effluent variability. During this experiment, the reactors could treat efficiently sewage with concentration as low as 200 mg COD/L. They could also be operated satisfactorily at an HRT as low as 2 hours, without problems of operational stability. The maximum COD removal efficiency can be achieved at CODInf exceeding 300 mg/L and HRT of 6 h.

Thermophilic Anaerobic Treatment of Sulfate-Rich Pulp and Paper Integrate Process Water

1991 ◽  
Vol 24 (3-4) ◽  
pp. 149-160 ◽  
Author(s):  
J. Rintala ◽  
J. L. Sanz Martin ◽  
G. Lettinga
Keyword(s):  
Sulfate Reduction ◽  
Removal Efficiency ◽  
Anaerobic Treatment ◽  
Cod Removal ◽  
Process Water ◽  
Upflow Anaerobic Sludge Blanket ◽  
Uasb Reactor ◽  
Anaerobic Sludge ◽  
Cod Removal Efficiency ◽  
Uasb Reactors

Anaerobic treatment of sulfate - rich (COD/SO4 ratio 1.4-2.1) clarified Whitewater from a thermomechanical pulping (TMP) process was studied in three laboratory-scale upflow anaerobic sludge blanket (UASB) reactors at 55°C and in batch digesters at 55° and 65°C. Different seed materials were used in the UASB reactors. The highest COD removal efficiency (effluent sulfide stripped) achieved was approximately 65 % in the UASB reactors. About 55 % COD removal efficiency was obtained at a loading rate of about 41 kgCODm−3d−1 in the UASB reactor seeded with thermophilic sludge cultivated with volatile fatty acids (VFAs). The total sulfide present in the liquid phase after anaerobic treatment accounted for approximately 65-78 % and 15-61 % of the removed COD in the batch digesters and the UASB reactors, respectively. Sulfate reduction was almost complete in the batch digesters, whereas about 24-64 % of sulfate was reduced in the UASB reactors. Acetate utilization for sulfate reduction was apparent in the batch digesters, whereas that could not be demonstrated in the UASB reactors. Sulfate reduction in the UASB reactors was obviously substrate limited. In conclusion, thermophilic anaerobic treatment is an alternative for the treatment of warm sulfate rich TMP process water.

Treatment Textiles Wastewater Using Anoxic Filter Bed and Biological Wriggle Bed-Ozone Biological Aerated Filter

2012 ◽  
Vol 518-523 ◽  
pp. 2961-2964
Author(s):  
Zhi Min Fu ◽  
Yu Gao Zhang ◽  
Xiao Jun Wang
Keyword(s):  
Removal Efficiency ◽  
Textile Wastewater ◽  
Cod Removal ◽  
Organic Polymer ◽  
Biological Aerated Filter ◽  
Polymer Carrier ◽  
Cod Removal Efficiency ◽  
Aerated Filter ◽  
Filter Bed ◽  
Better Than

Organic polymer carrier was utilized to treat textile wastewater. Results showed that COD removal efficiency was almost 82.8%. The average effluent COD concentration was 132.6 mg/L. The effluent colority was about 200 times. Experiment indicated that ceramic granular carrier was better than polymer carrier when ultlized to treat textil wastewater.

scholarly journals Biodegradation of textile wastewater: enhancement of biodegradability via the addition of co-substrates followed by phytotoxicity analysis of the effluent

2018 ◽  
Vol 2017 (2) ◽  
pp. 516-526 ◽  
Author(s):  
María Belén Ceretta ◽  
Ignacio Durruty ◽  
Ana Micaela Ferro Orozco ◽  
Jorge Froilán González ◽  
Erika Alejandra Wolski
Keyword(s):  
Removal Efficiency ◽  
Degradation Products ◽  
Textile Wastewater ◽  
Bacterial Consortium ◽  
Cod Removal ◽  
Treated Wastewater ◽  
Untreated Wastewater ◽  
Cod Removal Efficiency ◽  
Significant Efficacy ◽  
Microbial Treatments

Abstract This work reports on the biodegradation of textile wastewater by three alternative microbial treatments. A bacterial consortium, isolated from a dyeing factory, showed significant efficacy in decolourizing wastewater (77.6 ± 3.0%); the decolourization rate was 5.80 ± 0.31 mg of azo dye·L−1·h−1, without the addition of an ancillary carbon source (W). The degradation was 52% (measured as COD removal) and the products of the treatment showed low biodegradability (COD/BOD5 = 4.2). When glucose was added to the wastewater, (W + G): the decolourization efficiency increased to 87.24 ± 2.5% and the decolourization rate significantly improved (25.67 ± 3.62 mg·L−1·h−1), although the COD removal efficiency was only 44%. Finally, the addition of starch (W + S) showed both a similar decolourization rate and efficiency to the W treatment, but a higher COD removal efficiency (72%). In addition, the biodegradability of the treated wastewater was considerably improved (COD/BOD5 = 1.2) when starch was present. The toxicity of the degradation products was tested on Lactuca sativa seeds. In all treatments, toxicity was reduced with respect to the untreated wastewater. The W + S treatment gave the best performance.

The effects of hydraulic and organic shock loads on the robustness of upflow anaerobic sludge blanket reactors treating sewage

2006 ◽  
Vol 54 (2) ◽  
pp. 49-55 ◽  
Author(s):  
R.C. Leitão ◽  
S.T. Santaellla ◽  
A.C. van Haandel ◽  
G. Zeeman ◽  
G. Lettinga
Keyword(s):  
Removal Efficiency ◽  
Cod Removal ◽  
Ph Stability ◽  
Upflow Anaerobic Sludge Blanket ◽  
Anaerobic Sludge ◽  
Hydraulic Shock ◽  
Treatment Unit ◽  
Shock Loads ◽  
Cod Removal Efficiency ◽  
Uasb Reactors

In this investigation, the robustness and stability of UASB reactors was evaluated on the basis of four indicators: (i) COD removal efficiency; (ii) effluent variability; (iii) pH stability; and (iv) recovery time. The experiments were carried out using six pilot-scale UASB reactors fed with domestic sewage and operated under different operational conditions. After establishment of a “steady-state”, organic and hydraulic shock loads (six times the loading rate during six hours) were imposed. The results show that the UASB reactors are robust systems with regards to COD removal efficiency and pH stability when exposed to shock loads. However, this reactor cannot attenuate the imposed fluctuation in the influent COD. A secondary treatment unit is needed to retain the expelled sludge occurring as a result of a hydraulic shock load, or prior to the shock, a sufficient amount of sludge needs to be discharged from the reactor.

scholarly journals Investigation of Heavy Metal Effects on the Anaerobic Co-Digestion Process of Waste Activated Sludge and Septic Tank Sludge

2019 ◽  
Vol 2019 ◽  
pp. 1-9
Author(s):  
Quang-Minh Nguyen ◽  
Duy-Cam Bui ◽  
Thao Phuong ◽  
Van-Huong Doan ◽  
Thi-Nham Nguyen ◽  
...  
Keyword(s):  
Heavy Metals ◽  
Heavy Metal ◽  
Activated Sludge ◽  
Removal Efficiency ◽  
Biogas Production ◽  
Cod Removal ◽  
Septic Tank ◽  
Waste Activated Sludge ◽  
Digestion Process ◽  
Cod Removal Efficiency

The effect of copper, zinc, chromium, and lead on the anaerobic co-digestion of waste activated sludge and septic tank sludge in Hanoi was studied in the fermentation tests by investigating the substrate degradation, biogas production, and process stability at the mesophilic fermentation. The tested heavy metals were in a range of concentrations between 19 and 80 ppm. After the anaerobic tests, the TS, VS, and COD removal efficiency was 4.12%, 9.01%, and 23.78% for the Cu(II) added sample. Similarly, the efficiencies of the Zn(II) sample were 1.71%, 13.87%, and 16.1% and Cr(VI) efficiencies were 15.28%, 6.6%, and 18.65%, while the TS, VS, and COD removal efficiency of the Pb(II) added sample was recorded at 16.1%, 17.66%, and 16.03% at the concentration of 80 ppm, respectively. Therefore, the biogas yield also decreased by 36.33%, 31.64%, 31.64%, and 30.60% for Cu(II), Zn(II), Cr(VI), and Pb(II) at the concentration of 80 ppm, compared to the raw sample, respectively. These results indicated that Cu(II) had more inhibiting effect on the anaerobic digestion of the sludge mixture than Zn(II), Cr(VI), and Pb(II). The relative toxicity of these heavy metals to the co-digestion process was as follows: Cu (the most toxic) > Zn > Cr > Pb (the least toxic). The anaerobic co-digestion process was inhibited at high heavy metal concentration, which resulted in decreased removal of organic substances and produced biogas.

Sign in / Sign up

Export Citation Format

Share Document