Equivalent inclusion method-based simulation of particle sedimentation toward functionally graded material manufacturing

2014 ◽  
Vol 225 (4-5) ◽  
pp. 1429-1445 ◽  
Author(s):  
Y. J. Liu ◽  
H. M. Yin
Keyword(s):  
Functionally Graded Material ◽  
Functionally Graded ◽  
Particle Sedimentation ◽  
Equivalent Inclusion Method ◽  
Inclusion Method ◽  
Equivalent Inclusion ◽  
Graded Material

Predicting Speed of Crack Running in Functionally Graded Material

2005 ◽  
Author(s):  
Michihiko Nakagaki ◽  
Ryosuke Matsumoto
Keyword(s):  
Functionally Graded Material ◽  
Crack Tip ◽  
Functionally Graded ◽  
Constitutive Law ◽  
Nonlinear Material ◽  
Spherical Particles ◽  
Fracture Parameter ◽  
Crack Speed ◽  
Equivalent Inclusion Method ◽  
Graded Material

A theoretical and computational methodology for the analysis of the functionally graded material (FGM) is introduced, and its application is made to the problem of a dynamically propagating crack running transversely in the FGM, where the intensity of the estimated crack-tip severity is managed to keep in valance with the graded material toughness in the FGM during the propagation. To detect the crack-tip severity, an integral fracture parameter, T*, is used. The crack is propagated so that the value of T* is equated to the prescribed varying critical values of T* for the graded material. Emphasis is placed on the use of a fuzzy inference technique in order to control the crack speed, which is deduced from a few T* values immediately preceding the current crack position. As to describing the constitutive law for the FGM, micro-spherical particles of arbitrary size in mesoscale are considered to be randomly dispersed in the matrix medium. By assuming that the volume fraction of the inclusion is continuously varied from 0 to 100 percent in the material, the grading is modeled. For modeling the constitutive law for the FGM composite media of thermo-elastoplasticity, a closed form SCC-LRM constitutive model describing the nonlinear material mechanics of the particle-dispersed medium is used. The model is based on the self-consistent scheme and uses Eshelby’s equivalent inclusion method. Unprecedented analytical results of predicting the crack speed of a crack running transversely in the FGM plate are obtained. In some cases of material grading, apparent crack arresting is observed as the crack runs into the metal rich area of the FGM.

Elastohydrodynamic Lubrication of Inhomogeneous Materials Using the Equivalent Inclusion Method

2013 ◽  
Vol 136 (2) ◽  
Author(s):  
Zhanjiang Wang ◽  
Dong Zhu ◽  
Qian Wang
Keyword(s):  
Film Thickness ◽  
Surface Deformation ◽  
Fluid Pressure ◽  
Surface Displacement ◽  
Elastohydrodynamic Lubrication ◽  
Functionally Graded ◽  
Inhomogeneous Materials ◽  
Equivalent Inclusion Method ◽  
Inclusion Method ◽  
Equivalent Inclusion

Solid materials forming the boundaries of a lubrication interface may be elastoplastic, heat treated, coated with multilayers, or functionally graded. They may also be composites reinforced by particles or have impurities and defects. Presented in this paper is a model for elastohydrodynamic lubrication interfaces formed with these realistic materials. This model considers the surface deformation and subsurface stresses influenced by material inhomogeneities, where the inhomogeneities are replaced by inclusions with properly determined eigenstrains by means of the equivalent inclusion method. The surface displacement or deformation caused by inhomogeneities is introduced to the film thickness equation. The stresses are the sum of those caused by the fluid pressure and the eigenstrains. The lubrication of a material with a single inhomogeneity, multiple inhomogeneities, and functionally graded coatings are analyzed to reveal the influence of inhomogeneities on film thickness, pressure distribution, and subsurface stresses.

Material optimization of a cemented tibia tray using functionally graded material

2016 ◽  
Vol 58 (3) ◽  
pp. 260-268 ◽  
Author(s):  
Hassan S. Hedia ◽  
Saad M. Aldousari ◽  
Noha Fouda
Keyword(s):  
Functionally Graded Material ◽  
Functionally Graded ◽  
Material Optimization ◽  
Graded Material

Structural integrity and mechanical properties of the functionally graded material based on 316L/IN718 processed by DED technology

2021 ◽  
Vol 811 ◽  
pp. 141038
Author(s):  
Daniel Melzer ◽  
Jan Džugan ◽  
Martina Koukolíková ◽  
Sylwia Rzepa ◽  
Jaroslav Vavřík
Keyword(s):  
Mechanical Properties ◽  
Functionally Graded Material ◽  
Structural Integrity ◽  
Functionally Graded ◽  
Graded Material
Sign in / Sign up

Export Citation Format

Share Document