Fabrication and thermosensitive characteristics of BaCoO3−δ ceramics for low temperature negative temperature coefficient thermistor

2017 ◽  
Vol 28 (8) ◽  
pp. 6239-6244 ◽  
Author(s):  
Zhenhua Hu ◽  
Huimin Zhang ◽  
Junhua Wang ◽  
Long Chen ◽  
Xianxian Xie ◽  
...  
2015 ◽  
Vol 3 (3) ◽  
pp. 1317-1324 ◽  
Author(s):  
Yanrong Wang ◽  
Bin Liu ◽  
Songhua Xiao ◽  
Han Li ◽  
Lingling Wang ◽  
...  

A catalytically activated hydrogen sensor is obtained based on Pd decorated WO3 nanoplates constructed by a solvothermal method.


2020 ◽  
Vol 22 (5) ◽  
pp. 2986-2998 ◽  
Author(s):  
Vijay Khopkar ◽  
Balaram Sahoo

The microstructure and low-temperature dielectric properties of lead-free BaFe0.5Nb0.5O3 ceramics exhibiting a negative temperature coefficient of resistance behavior.


1973 ◽  
Vol 51 (18) ◽  
pp. 3152-3155 ◽  
Author(s):  
Huw O. Pritchard

It is shown that previously calculated nonequilibrium rate constants for the dissociation of H2 and D2 appear to approach a rotationally averaged equilibrium expression at low temperature. This equilibrium form of the rate expression itself has an Arrhenius temperature coefficient for dissociation which is significantly less than the dissociation energy, and the corresponding recombination rate constant has a negative temperature coefficient. The reasons for this are explained.


2021 ◽  
Vol 1114 (1) ◽  
pp. 012077
Author(s):  
P P Vishnupriya ◽  
Thomas Jaini ◽  
Binoy Mariya ◽  
P Nair Praseetha ◽  
R Ranjana ◽  
...  

Author(s):  
Vahid Hosseini ◽  
W. Stuart Neill ◽  
M. David Checkel

One potential method for controlling the combustion phasing of a Homogeneous Charge Compression Ignition (HCCI) engine is to vary the fuel chemistry using two fuels with different auto-ignition characteristics. Although a dual-fuel engine concept is technically feasible with current engine management and fuel delivery system technologies, this is not generally seen as a practical solution due to the necessity of supplying and storing two fuels. Onboard partial reforming of a hydrocarbon fuel is seen to be a more attractive way to realize a dual-fuel concept while relying on only one fuel supply infrastructure. Reformer Gas (RG) is a mixture of light gases dominated by hydrogen and carbon monoxide that can be produced from any hydrocarbon fuel using an onboard fuel processor. RG has a high resistance to auto-ignition and wide flammability limits. The ratio of H2 to CO produced depends on the reforming method and conditions, as well as the hydrocarbon fuel. In this study, a CFR engine was operated in HCCI mode at elevated intake air temperatures and pressures. n-heptane was used as the hydrocarbon blending component because of its high cetane number and well-known fuel chemistry. RG was used as the low cetane blending component to retard the combustion phasing. Other influential parameters such as air/fuel ratio, EGR, and intake temperature were maintained constant. The experimental results show that increasing the RG fraction retards the combustion phasing to a more optimized value causing indicated power and fuel conversion efficiency to increase. RG reduced the first stage of heat release, extended the negative temperature coefficient delay period, and retarded the main stage of combustion. Two extreme cases of RG composition with H2/CO ratios of 3/1 and 1/1 were investigated. The results show that both RG compositions retard the combustion phasing, but that the higher hydrogen fraction RG is more effective. A single-zone model with detailed chemical kinetics was used to interpret the experimental results. The effect of RG on combustion phasing retardation was confirmed. It was found that the low temperature heat release was inhibited by a reduction of intermediate radical mole fractions during low temperature reactions and the early stages of the negative temperature coefficient delay period.


Sign in / Sign up

Export Citation Format

Share Document