Preparation of Activated Bio-char from Corn Stalk for Color Treatment of Effluent from Packaging Paper Mill

2021 ◽  
Vol 232 (9) ◽  
Author(s):  
Phan Huy Hoang ◽  
Nguyen Minh Dat ◽  
Nguyen Thi Thanh
TAPPI Journal ◽  
2015 ◽  
Vol 14 (2) ◽  
pp. 73-81 ◽  
Author(s):  
GISELY SAMISTRARO ◽  
PETER W. HART ◽  
JORGE LUIZ COLODETTE ◽  
RICARDO PAIM

Eucalyptus dunii has been commercially used in southern Brazil because of its relatively good frost tolerance and adequate productivity in the winter months. More recently, interest has grown in cultivating Eucalyptus benthamii Maiden & Cambage, which presents even superior frost tolerance compared to E. dunii and is highly productive as well. The quality of E. benthamii for pulp production is not yet proven. Thus, the chemical, anatomical, and technological aspects of pulp made from E. benthamii were compared with those of E. dunii for unbleached paper production. Samples of E. benthamii chips were obtained and analyzed for their basic density, chemical composition, higher heating value, trace elemental analysis, and chip size distribution. The chips were kraft cooked using conditions that produced a 74 ± 6 kappa number. The pulps were characterized for kappa number, yield, viscosity, and morphologic characteristics (e.g., length, wall thickness, and coarseness). Black liquor was analyzed for total solids, organics, inorganics, sodium sulfide, sodium hydroxide, and sodium carbonate. Brownstocks were beaten at five different energy levels in a Valley beater, and the physical strength properties of 120 g/m² handsheets were measured to develop a beater curve. The results of this study showed differences in delignification between the two woods and lower pulp yield for E. benthamii , which are related to their chemical compositions and basic densities. The E. benthamii studied in this work exhibited higher amounts of lignin and extractives, lower carbohydrate content, and lower basic density. However, cooking a blend of the two woods afforded good results in pulping and in physical pulp properties.


TAPPI Journal ◽  
2009 ◽  
Vol 8 (3) ◽  
pp. 14-20 ◽  
Author(s):  
YUAN-SHING PERNG ◽  
EUGENE I-CHEN WANG ◽  
SHIH-TSUNG YU ◽  
AN-YI CHANG

Trends toward closure of white water recirculation loops in papermaking often lead to a need for system modifications. We conducted a pilot-scale study using pulsed electrocoagulation technology to treat the effluent of an old corrugated containerboard (OCC)-based paper mill in order to evaluate its treatment performance. The operating variables were a current density of 0–240 A/m2, a hydraulic retention time (HRT) of 8–16 min, and a coagulant (anionic polyacrylamide) dosage of 0–22 mg/L. Water quality indicators investigated were electrical con-ductivity, suspended solids (SS), chemical oxygen demand (COD), and true color. The results were encouraging. Under the operating conditions without coagulant addition, the highest removals for conductivity, SS, COD, and true color were 39.8%, 85.7%, 70.5%, and 97.1%, respectively (with an HRT of 16 min). The use of a coagulant enhanced the removal of both conductivity and COD. With an optimal dosage of 20 mg/L and a shortened HRT of 10 min, the highest removal achieved for the four water quality indicators were 37.7%, 88.7%, 74.2%, and 91.7%, respectively. The water qualities thus attained should be adequate to allow reuse of a substantial portion of the treated effluent as process water makeup in papermaking.


TAPPI Journal ◽  
2019 ◽  
Vol 18 (2) ◽  
pp. 93-99
Author(s):  
SEYYED MOHAMMAD HASHEMI NAJAFI ◽  
DOUGLAS BOUSFIELD, ◽  
MEHDI TAJVIDI

Cracking at the fold of publication and packaging paper grades is a serious problem that can lead to rejection of product. Recent work has revealed some basic mechanisms and the influence of various parameters on the extent of crack area, but no studies are reported using coating layers with known mechanical properties, especially for double-coated systems. In this study, coating layers with different and known mechanical properties were used to characterize crack formation during folding. The coating formulations were applied on two different basis weight papers, and the coated papers were folded. The binder systems in these formulations were different combinations of a styrene-butadiene latex and mixtures of latex and starch for two different pigment volume concentrations (PVC). Both types of papers were coated with single and double layers. The folded area was scanned with a high-resolution scanner while the samples were kept at their folded angle. The scanned images were analyzed within a constant area. The crack areas were reported for different types of papers, binder system and PVC values. As PVC, starch content, and paper basis weight increased, the crack area increased. Double layer coated papers with high PVC and high starch content at the top layer had more cracks in comparison with a single layer coated paper, but when the PVC of the top layer was low, cracking area decreased. No measurable cracking was observed when the top layer was formulated with a 100% latex layer.


Sign in / Sign up

Export Citation Format

Share Document