Composition and heat-treatment effects on the adhesion strength of Sn-Zn-Al solders on Cu substrate

JOM ◽  
2000 ◽  
Vol 52 (6) ◽  
pp. 36-39 ◽  
Author(s):  
Shan-Pu Yu ◽  
Min-Hsiung Hon ◽  
Hsin-Chien Wang ◽  
Moo-Chin Wang
Keyword(s):  
Heat Treatment ◽  
Adhesion Strength ◽  
Treatment Effects ◽  
Cu Substrate

Structural and FEM analysis of heat treatment effects on mild steel

2021 ◽  
Author(s):  
Aaditya Srivastava ◽  
Ansh Jain ◽  
Shubham Rajput ◽  
Hari Om Singh ◽  
Bhaskar Chandra Kandpal ◽  
...  
Keyword(s):  
Heat Treatment ◽  
Mild Steel ◽  
Treatment Effects ◽  
Fem Analysis

Heat-treatment effects on the Raman scattering spectra of NdBa2Cu3O7−δ

2003 ◽  
Vol 392-396 ◽  
pp. 175-180
Author(s):  
N. Watanabe ◽  
R. Hareyama ◽  
T. Machi ◽  
S. Arai ◽  
N. Koshizuka ◽  
...  
Keyword(s):  
Heat Treatment ◽  
Raman Scattering ◽  
Treatment Effects ◽  
Scattering Spectra ◽  
Raman Scattering Spectra

Effect of dislocation density on adhesion strength of electroforming Ni layer on Cu substrate

2018 ◽  
Vol 33 (3) ◽  
pp. 301-313
Author(s):  
Zhong Zhao ◽  
Pengcheng Zhu ◽  
Linchu Yang ◽  
Yaoxiang Geng
Keyword(s):  
Dislocation Density ◽  
Adhesion Strength ◽  
Cu Substrate

Evaluation of Heat Treatment Effects on the Electrocatalytic Properties of AuCu Intermetallic Nanocrystals

2015 ◽  
Vol 162 (6) ◽  
pp. H301-H307 ◽  
Author(s):  
Tingting Yu ◽  
Baozhan Zheng ◽  
Lei Zhang ◽  
Zhen Wang ◽  
Dan Xiao ◽  
...  
Keyword(s):  
Heat Treatment ◽  
Treatment Effects ◽  
Electrocatalytic Properties

scholarly journals Effect of Deposition Conditions on Phase Content and Mechanical Properties of Yttria-Stabilized Zirconia Thin Films Deposited by Sol-Gel/Dip-Coating

2021 ◽  
Vol 2021 ◽  
pp. 1-9
Author(s):  
Francisco J. Cano ◽  
Orlando Castilleja-Escobedo ◽  
L. J. Espinoza-Pérez ◽  
Cecilia Reynosa-Martínez ◽  
Eddie Lopez-Honorato
Keyword(s):  
Heat Treatment ◽  
Wear Rate ◽  
Adhesion Strength ◽  
Surface Defects ◽  
Sol Gel ◽  
Dip Coating ◽  
Yttria Stabilized Zirconia ◽  
Cubic Phase ◽  
Phase Content ◽  
Stabilized Zirconia

The effect of yttria concentration (0-33.4 mol%), extraction rates (0.17, 0.33, 0.50, and 0.67 mm s-1), and the number of layers (up to four) on the phase content, surface defects, thickness, hardness, adhesion strength, and wear rate of yttria-stabilized zirconia coatings produced by sol-gel/dip-coating were studied for its use on thermolabile substrates. At 700°C, a metastable tetragonal phase ( t ″ ) was obtained even with 33.4 mol% yttria when heat treated for 24 hours; however, a fully cubic structure was attained by extending the heat treatment up to 48 hours as confirmed by Raman spectroscopy. Furthermore, it was necessary to use withdrawal speeds of at least 0.67 mm s-1 to produce defect-free coatings. Although the coatings were produced at low temperature, they showed 41% lower wear rate than steel and an adhesion strength of 30 MPa. Our work stresses the importance of the heat treatment history on the stabilization of the cubic phase in sol-gel YSZ coatings.

Sign in / Sign up

Export Citation Format

Share Document