Parametric study on the fatigue life of railways under rolling contact fatigue by three-dimensional numerical analysis

2012 ◽  
Vol 26 (2) ◽  
pp. 359-365 ◽  
Author(s):  
Doo-Ho Cho ◽  
Hwan Seong ◽  
Young-Jin Kim ◽  
Jae-Boong Choi ◽  
Hyun-Kyu Jun ◽  
...  
Keyword(s):  
Fatigue Life ◽  
Numerical Analysis ◽  
Parametric Study ◽  
Rolling Contact Fatigue ◽  
Three Dimensional ◽  
Contact Fatigue ◽  
Rolling Contact

Effect of Grain Flow Orientation on Rolling Contact Fatigue Life of AISI M-50

1982 ◽  
Vol 104 (3) ◽  
pp. 330-334 ◽  
Author(s):  
A. H. Nahm
Keyword(s):  
Fatigue Life ◽  
Flow Line ◽  
Flow Direction ◽  
Rolling Contact Fatigue ◽  
Contact Fatigue ◽  
Rolling Contact ◽  
Vacuum Arc ◽  
Type I ◽  
Grain Flow ◽  
Contact Fatigue Life

Accelerated rolling contact fatigue tests were conducted to study the effect of grain flow orientation on the rolling contact fatigue life of vacuum induction melted and vacuum arc remelted (VIM-VAR) AISI M-50. Cylindrical test bars were prepared from a billet with 0, 45, and 90 deg orientations relative to billet forging flow direction. Tests were run at a Hertzian stress of 4,826 MPa with a rolling speed of 12,500 rpm at room temperature, and lubricated with Type I (MIL-L-7808G) oil. It was observed that rolling contact fatigue life increased when grain flow line direction became more parallel to the rolling contact surface.

scholarly journals Rolling Wear of Silicon Nitride Bearing Materials

1990 ◽  
Author(s):  
John W. Lucek
Keyword(s):  
Fatigue Life ◽  
Silicon Nitride ◽  
Failure Modes ◽  
Fatigue Testing ◽  
Rolling Contact Fatigue ◽  
Contact Fatigue ◽  
Rolling Contact ◽  
Wear Performance ◽  
Wear Rates ◽  
Bearing Materials

Rolling-contact fatigue test methods were used to measure the wear performance of several silicon nitride materials. Sintered, hot pressed and hot isostatically pressed materials exhibited wear rates ranging over three orders of magnitude. Hot isostatically pressed materials had the lowest wear rates. Despite the disparity in wear performance, all materials tested had useful rolling-contact fatigue lives compared to steel. Fatigue life estimates, failure modes, and rolling wear performance for theses ceramics are compared to M-50 steel. This work highlights the rapid contact stress reductions that occur due to conformal wear in rolling-contact fatigue testing. Candidate bearing materials with unacceptably high wear rates may exhibit useful fatigue lives. Rolling contact bearing materials must possess useful wear and fatigue resistance. Proper performance screening of candidate bearing materials must describe the failure mode, wear rate, and the fatigue life. Guidelines for fatigue testing methods are proposed.

Influence of ZnDTP on Rolling Contact Fatigue Life under Grease Lubrication

2021 ◽  
Vol 2021.59 (0) ◽  
pp. 05a5
Author(s):  
Hirotomo HOSOI ◽  
Yugo KAMEI ◽  
Hirotoshi AKIYAMA ◽  
Jusei MAEDA ◽  
Masanori SEKI
Keyword(s):  
Fatigue Life ◽  
Rolling Contact Fatigue ◽  
Contact Fatigue ◽  
Rolling Contact ◽  
Grease Lubrication ◽  
Contact Fatigue Life

Evaluation of contact fatigue life of a wind turbine carburized gear considering gradients of mechanical properties

2018 ◽  
Vol 28 (8) ◽  
pp. 1170-1190 ◽  
Author(s):  
Wei Wang ◽  
Huaiju Liu ◽  
Caichao Zhu ◽  
Zhangdong Sun
Keyword(s):  
Residual Stress ◽  
Fatigue Life ◽  
Rolling Contact Fatigue ◽  
Contact Fatigue ◽  
Rolling Contact ◽  
Heavy Duty ◽  
Initial Residual Stress ◽  
Contact Fatigue Life ◽  
Carburized Gear ◽  
Load Conditions

Case hardening processes such as carburizing are extensively applied in heavy-duty gears used in wind turbines, ships, high-speed rails, etc. Contact fatigue failure occurs commonly in engineering practice, thus reduces reliabilities of those machines. Rolling contact fatigue life of a carburized gear is influenced by factors such as the gradients of mechanical properties and profile of initial residual stress. In this regard, the study of contact fatigue life of carburized gears should be conducted with the consideration of those aspects. In this study, a finite element elastic–plastic contact model of a carburized gear is developed which takes the gradients of hardness and initial residual stress into account. Initial residual stress distribution and the hardness profile along the depth are obtained through experimental measurements. The effect of the hardness gradient is reflected by the gradients of yield strength and fatigue parameters. The modified Fatemi–Socie strain-life criterion is used to estimate the rolling contact fatigue life of the heavy-duty carburized gear. Numerical results reveal that according to the Fatemi–Socie fatigue life criterion, rolling contact fatigue failure of the carburized gear will first initiate at subsurface rather than surface. Compared with the un-carburized gear, the rolling contact fatigue lives of the carburized gear under all load conditions are significantly improved. Under heavy load conditions, the carburized layer significantly reduces the fatigue damage mainly due to the benefit to inhibit the accumulation of plasticity. Influence of the residual stress is also investigated. Under the nominal load condition, compared with the residual stress-free case, the existence of the tensile residual stress causes remarkable deterioration of the rolling contact fatigue life while the compressive residual stress with the same magnitude leads to a moderate growth of the rolling contact fatigue life. As the load becomes heavier when plasticity becomes notable, the influence of the initial residual stress on the life is somewhat weakened.

Sign in / Sign up

Export Citation Format

Share Document