Grain refinement in the coarse-grained region of the heat-affected zone in low-carbon high-strength microalloyed steels

2010 ◽  
Vol 17 (6) ◽  
pp. 737-741 ◽  
Author(s):  
Ran Wei ◽  
Cheng-jia Shang ◽  
Kai-ming Wu
Keyword(s):  
Grain Refinement ◽  
Heat Affected Zone ◽  
High Strength ◽  
Coarse Grained ◽  
Microalloyed Steels ◽  
Low Carbon

scholarly journals Metallurgical Effects of Niobium and Molybdenum on Heat-Affected Zone Toughness in Low-Carbon Steel

2019 ◽  
Vol 9 (9) ◽  
pp. 1847 ◽  
Author(s):  
Hardy Mohrbacher
Keyword(s):  
Heat Treatment ◽  
Heat Affected Zone ◽  
High Strength ◽  
Post Weld Heat Treatment ◽  
Coarse Grained ◽  
Accelerated Cooling ◽  
Low Carbon ◽  
Structural Applications ◽  
Steel Grades ◽  
Weld Heat

Modern weldable high strength steel grades are typically based on low-carbon alloy concepts using microalloying for obtaining a good strength-toughness balance. Such steel grades having a yield strength in the range of 420 to 690 MPa are very commonly used in pipelines, heavy vehicles, shipbuilding and general structural applications. Thermomechanical processing during hot rolling combined with accelerated cooling is an established means of producing such steel grades. Considering the alloying concepts, the use of niobium and molybdenum, and in selected cases boron, is very efficient to achieve high strength and good toughness. However, all targeted applications of such high strength steels involve extensive welding. Thus, heat affected zone properties are of particular importance. The present paper investigates the effects of Nb, Mo and Ti on the heat affected zone properties. Variations of the Mn and Si contents are considered as well. Additionally, the influence of post-weld heat treatment in the coarse-grained heat-affected zone (HAZ) is considered. In this approach, HAZ subzones were generated using laboratory weld cycle simulations in combination with systematic variation of alloying elements to scrutinize and interpret their specific effects. The results indicate that Mo and Nb, when alloyed in the typical range, provide excellent HAZ toughness and guarantee sufficiently low ductile-to-brittle transition temperature. An alloy combination of Nb, Mo and Ti improves performance under hot deformation conditions and toughness after post-weld heat treatment.

Effect of Microstructure on High-Strength Low-Alloy Steel Welded Joint Toughness with Simulation of Heat-Affected Zone Coarse-Grained Area

Metallurgist ◽  
2021 ◽  
Vol 64 (9-10) ◽  
pp. 875-884
Author(s):  
K. G. Vorkachev ◽  
P. P. Stepanov ◽  
L. I. Éfron ◽  
M. M. Kantor ◽  
A. V. Chastukhin ◽  
...  
Keyword(s):  
Alloy Steel ◽  
Heat Affected Zone ◽  
Welded Joint ◽  
High Strength ◽  
Coarse Grained ◽  
Low Alloy Steel ◽  
Effect Of Microstructure

Microstructural Refinement in a Commercial Aluminum Alloy Processed by ECAP Using a Die Channel Angle of 110 Degrees

2015 ◽  
Vol 1114 ◽  
pp. 3-8
Author(s):  
Nicolae Şerban ◽  
Doina Răducanu ◽  
Nicolae Ghiban ◽  
Vasile Dănuţ Cojocaru
Keyword(s):  
Grain Refinement ◽  
Cross Section ◽  
High Strength ◽  
Secondary Phase ◽  
Coarse Grained ◽  
Metallographic Analysis ◽  
Second Phase ◽  
Channel Angle ◽  
Ambient Temperatures ◽  
Fine Grained

The properties of ultra-fine grained materials are superior to those of corresponding conventional coarse grained materials, being significantly improved as a result of grain refinement. Equal channel angular pressing (ECAP) is an efficient method for modifying the microstructure by refining grain size via severe plastic deformation (SPD) in producing ultra-fine grained materials (UFG) and nanomaterials (NM). The grain sizes produced by ECAP processing are typically in the submicrometer range and this leads to high strength at ambient temperatures. ECAP is performed by pressing test samples through a die containing two channels, equal in cross-section and intersecting at a certain angle. The billet experiences simple shear deformation at the intersection, without any precipitous change in the cross-section area because the die prevents lateral expansion and therefore the billet can be pressed more than once and it can be rotated around its pressing axis during subsequent passes. After ECAP significant grain refinement occurs together with dislocation strengthening, resulting in a considerable enhancement in the strength of the alloys. A commercial AlMgSi alloy (AA6063) was investigated in this study. The specimens were processed for a number of passes up to nine, using a die channel angle of 110°, applying the ECAP route BC. After ECAP, samples were cut from each specimen and prepared for metallographic analysis. The microstructure of the ECAP-ed and as-received material was investigated using optical (OLYMPUS – BX60M) and SEM microscopy (TESCAN VEGA II – XMU). It was determined that for the as-received material the microstructure shows a rough appearance, with large grains of dendritic or seaweed aspect and with a secondary phase at grain boundaries (continuous casting structure). For the ECAP processed samples, the microstructure shows a finished aspect, with refined, elongated grains, also with crumbled and uniformly distributed second phase particles after a typical ECAP texture.

Effect of Welding Processes with High Heat Input on the Microstructure and Toughness of Coarse-Grained Heat-Affected Zone of a High-Strength High-Toughness Steel

2018 ◽  
Vol 937 ◽  
pp. 61-67
Author(s):  
Yu Jie Li ◽  
Jin Wei Lei ◽  
Xuan Wei Lei ◽  
Oleksandr Hress ◽  
Kai Ming Wu
Keyword(s):  
Low Temperature ◽  
Impact Toughness ◽  
Heat Affected Zone ◽  
Heat Input ◽  
High Strength ◽  
High Heat ◽  
Coarse Grained ◽  
Low Temperature Impact Toughness ◽  
The Impact ◽  
Welding Processes

Utilizing submerged arc welding under heat input 50 kJ/cm on 60 mm thick marine engineering structure plate F550, the effect of preheating and post welding heat treatment on the microstructure and impact toughness of coarse-grained heat-affected zone (CGHAZ) has been investigated. The original microstructure of the steel plate is tempered martensite. The yield and tensile strength is 610 and 660 MPa, respectively. The impact absorbed energy at low temperature (-60 °C) at transverse direction reaches about 230~270 J. Welding results show that the preheating at 100 °C did not have obvious influence on the microstructure and toughness; whereas the tempering at 600 °C for 2.5 h after welding could significantly reduce the amount of M-A components in the coarse-grained heat-affected zone and thus improved the low temperature impact toughness.

Sign in / Sign up

Export Citation Format

Share Document