Discussion of the paper, “elastic analysis for a radial crack in a circular ring”. by O. L. Bogie and C. E. Freese

1972 ◽  
Vol 4 (2) ◽  
pp. 323
Author(s):  
J.H. Underwood
1972 ◽  
Vol 4 (2) ◽  
pp. 315-321 ◽  
Author(s):  
O.L. Bowie ◽  
C.E. Freese

2018 ◽  
Vol 7 (3) ◽  
pp. 1826
Author(s):  
Heyam H. Shaalan ◽  
Mohd Ashraf Mohamad Ismail ◽  
Romziah Azit

Shotcrete is ordinary concrete applied to the surface under high pressure. It demonstrates a highly time-dependent behaviour after few hours of application. Traditional approaches assume a simple linear elastic behaviour using a hypothetical young modulus to investigate the time-dependency and creep effects. In this paper, a new constitutive model of shotcrete is applied to evaluate the time-dependent behaviour of a TBM tunnel lining and investigate the parameters that can influence this behaviour. The Shotcrete model is based on the framework of Elasto-plasticity and designed to model shotcrete linings more realistically. The basic data of Pahang-Selangor Raw Water Transfer Project is used for the analysis study. An attempt is made to investigate the influence of some input parameters of the shotcrete model on the time-dependent behaviour of the shotcrete lining. These parameters include the time-dependent stiffness/strength parameters, creep and shrinkage parameters and steel fibre parameters. The variation in shotcrete strength classes causes a noticeable influence on the development of shotcrete compressive strength with time, particularly during the first days of application. The creep and shrinkage strain cause a considerable reduction in the development of the shotcrete stress with time. The impact of steel fibre content is determined, and the result indicated that the development of plain shotcrete stresses with time is lower than that of the reinforced shotcrete. In addition, a comparison study is performed to analyse the tunnel lining behaviour using both shotcrete model and an elastic analysis. Significant differences in shotcrete lining stresses are achieved when using the elastic analysis while the shotcrete model results in a reasonable result that can be used for the design requirements. 


Author(s):  
István Ecsedi ◽  
Attila Baksa

AbstractThis paper deals with the Saint-Venant torsion of elastic, cylindrically orthotropic bar whose cross section is a sector of a circular ring shaped bar. The cylindrically orthotropic homogeneous elastic wedge-shaped bar strengthened by on its curved boundary surfaces by thin isotropic elastic shells. An analytical method is presented to obtain the Prandtl’s stress function, torsion function, torsional rigidity and shearing stresses. A numerical example illustrates the application of the developed analytical method.


Author(s):  
C. Phongcharoenpanich ◽  
Y. Chawanonphithak ◽  
P. Wounchoum ◽  
M. Krairiksh
Keyword(s):  

2021 ◽  
pp. 112067212199472
Author(s):  
Luis Izquierdo ◽  
Ana M Rodríguez ◽  
Ramón A Sarquis ◽  
Diego Altamirano ◽  
Maria A Henriquez

Purpose: To evaluate and compare visual and refractive outcomes after implantation of the intracorneal continuous ring 360° arc (ICCR) versus the intracorneal ring segment 340° arc (ICRS) using femtosecond laser for central keratoconus. Setting: Research Department, Oftalmosalud, Instituto de Ojos, Lima, Peru. Methods: Randomized study that included 40 eyes of 32 patients diagnosed with central keratoconus between November 2014 and March 2015. Twenty eyes had an implantation of ICCR (MyoRing, Dioptex GmbH, Austria) through an intrastromal pocket and 20 eyes had an implantation of ICRS (Keraring, Mediphacos, Brazil) through an intrastromal tunnel. Both procedures were performed with a femtosecond laser (LDV Z6 model, Ziemer Ophthalmic Systems AG). Visual acuity (VA), refraction, and Scheimpflug imaging analysis were performed pre- and postoperatively at 1 month and 1 year. Comparisons of means were performed using the Student’s t-test. Results: At 1 year, uncorrected VA improved 0.77 LogMAR ( p < 0.001) in the ICCR group and 0.79 LogMAR ( p = 0.01) in the ICRS group; mean sphere improvement was 5.13 Diopters (D) in the ICCR group and 6.27 D in the ICRS group ( p < 0.001 both); mean Steeper Keratometry improvement was 4.24 D in the ICCR group and 5.53 D in the ICRS group ( p < 0.001 both). In the ICCR group, mean decrease in the pachymetry at the thinnest point of the cornea was 32.16 µm ( p = 0.01), and in the ICRS group, mean increase was 4.2 µm at 1 year ( p = 0.61). Conclusion: Intracorneal continuous ring 360° arc (ICCR) and intracorneal ring segment 340° (ICRS) are effective treatments for central keratoconus. No significant differences between rings were found on visual acuity, refraction, and keratometry improvement.


Sign in / Sign up

Export Citation Format

Share Document