The moisture content-equilibrium relative humidity relationships of five varieties of Canadian wheat and of candle rapeseed at different temperatures

1981 ◽  
Vol 17 (4) ◽  
pp. 187-190 ◽  
Author(s):  
S.W. Pixton ◽  
Sylvia Henderson
2019 ◽  
Vol 62 (5) ◽  
pp. 1075-1086
Author(s):  
David R. Bohnhoff ◽  
Rhonda K. Bohnhoff

Abstract. Hybrid hazelnuts that are predominately a cross between the American hazelnut () and the European hazelnut () are being grown and evaluated as part of an effort to develop a thriving hazelnut industry for the Upper Midwest of the U.S. Along with this plant development effort, researchers are investigating and assessing various harvesting and processing methods and equipment in an effort to create a robust and food-safe production industry. One harvesting alternative is to pick hazelnut clusters off plants before the nuts fully ripen and fall to the ground, an approach that requires greater attention to drying. Whether entire clusters are dried or the nuts are separated from the husks prior to drying is a decision that will be influenced by the drying requirements and potential uses for these hazelnut fractions. To this end, a study was undertaken to establish desorption isotherms for the husks, shells, and kernels of hybrid hazelnuts grown in the Upper Midwest. Clusters were hand-picked from shrubs in Wisconsin and immediately placed in 18 different controlled environments (six different relative humidity levels at three different temperatures). Actual moisture conditioning took place over saturated salt solutions in specially fabricated biomaterial moisture conditioning units. After a six-week period during which the clusters reached equilibrium with their environment via desorption, they were separated into husk, shell, and kernel fractions and returned to their respective conditioning units. After another six weeks in the conditioning units, the moisture content (MC) of each fraction was determined by oven-drying at 103°C for 48 h. Under equilibrium conditions, the kernel MC was found to be only 37% of that for shells, whereas the equilibrium moisture content (EMC) values for husks were on average 14% greater than those for shells. On a dry basis, the average cluster mass was 32.9% husk, 43.9% shell, and 23.2% kernel. Likewise, on a dry basis, the average whole nut mass was 65.5% shell and 34.5% kernel. The desorption data were fit to the Modified Henderson, Modified Chung-Pfost, Modified Halsey, Modified Oswin, and Modified GAB equations. Overall, the best fit to the experimental data was provided by the Modified Chung-Pfost equation with parameters determined using equilibrium relative humidity (ERH) as the dependent variable in regression analyses. For ERH values above 0.70, the temperature-modified form of the GAB equation is recommended for predicting desorption EMC values for hazelnut fractions. Keywords: Desorption, Equilibrium moisture content, Equilibrium relative humidity, Hazelnuts, Kernels, Nuts, Shells, Water activity.


CERNE ◽  
2016 ◽  
Vol 22 (4) ◽  
pp. 423-430 ◽  
Author(s):  
Ananias Francisco Dias Júnior ◽  
Lucas Pereira Pirola ◽  
Saly Takeshita ◽  
Artur Queiroz Lana ◽  
José Otávio Brito ◽  
...  

ABSTRACT This research aimed to evaluate hygroscopicity of charcoal produced under four different final carbonization temperatures. For evaluation of hygroscopicity charcoal samples were conditioned in environments with controlled temperature and relative humidity, using saturated salt solutions. The final carbonization temperature significantly influenced the products yields and the properties of charcoal. The charcoal produced in the final temperature of 750 °C showed the highest adsorption capacity of water, indicated by the moisture content after conditioning, in the higher relative humidity environment. Correlations were observed between adsorbed moisture and the porosity of charcoal produced.


2019 ◽  
Vol 35 (4) ◽  
pp. 475-479 ◽  
Author(s):  
Jun Sian Lee ◽  
Shahab Sokhansanj ◽  
C. Jim Lim ◽  
Anthony Lau ◽  
Tony Bi

Abstract.The published data on equilibrium moisture content vs. equilibrium relative humidity (EMC-ERH) for wood pellet do not cover the range of temperature and relative humidity to which a pellet is exposed to during its storage and handling. A few published EMC-ERH relations covering a wider range of temperatures and relative humidity are available for solid wood (lumber) and wood chips. The question is whether the data for solid wood is applicable to wood pellets. For this research, we examined the sorption isotherms of wood pellets and solid wood. The analysis shows that EMC for solid wood is higher than the EMC for wood pellet for a relative humidity larger than 30%. The slope of EMC-ERH isotherm for solid wood in the range of 30%-70% is slightly steeper than the slope of isotherm for wood pellet, indicating the pellet’s EMC is less sensitive to ERH when compared to EMC-ERH for solid wood. Keywords: EMC, ERH, Densified biomass, Equilibrium moisture content, Equilibrium relative humidity, Solid wood, Wood pellets.


Holzforschung ◽  
2007 ◽  
Vol 61 (2) ◽  
pp. 175-181 ◽  
Author(s):  
Henrik Lund Frandsen ◽  
Staffan Svensson ◽  
Lars Damkilde

Abstract The equilibrium moisture content in wood depends not only on the current relative humidity in ambient air, but also on the history of relative humidity variations. This hysteresis dependence of sorption in wood implies that in the worst case the moisture content for a given relative humidity may deviate by 30–35%. While researchers seem to have reached a general agreement on the hypothesis for the sorption hysteresis phenomenon, only a few models describing the phenomenon are available. Current models such as the independent domain model have numerical deficiencies and drawbacks. This paper presents a new hysteresis model, which mathematically resolves in closed-form expressions, with the current relative humidity and moisture content as the only input parameters. Furthermore, the model has the advantage of being applicable to different sorption isotherms, i.e., different species and different temperatures. These features make the model relatively easy to implement into a numerical method such as the finite element method.


Sign in / Sign up

Export Citation Format

Share Document