scholarly journals A CONTRIBUTION TO THE ANALYSIS OF QUASI STATIC CRACK GROWTH IN SHEET MATERIALS

1978 ◽  
pp. 25-31 ◽  
Author(s):  
A.U. de Koning
Keyword(s):  
Crack Growth ◽  
Sheet Materials ◽  
Static Crack

Fatigue and Static Crack Growth Rate of Alloy 718 Under Cathodic Polarization

CORROSION ◽  
10.5006/3572 ◽  
2021 ◽  
Author(s):  
Ramgopal Thodla ◽  
Anand Venkatesh
Keyword(s):  
Growth Rate ◽  
Fatigue Crack ◽  
Crack Growth Rate ◽  
Fatigue Crack Growth ◽  
Crack Growth ◽  
Fatigue Crack Growth Rate ◽  
Cathodic Polarization ◽  
Alloy 718 ◽  
Static Crack ◽  
Rate Behavior

Fatigue crack growth rate was developed on three heats of alloy 718 (UNS N07718) under cathodic polarization, over a wide range of loading conditions. Fatigue crack growth rate increased with decreasing frequency over a range of Kmax and K conditions. In most cases, there was no evidence of a plateau in fatigue crack growth rate at low frequencies. The fatigue crack growth rate over the range of conditions evaluated were influenced by static crack growth rate at Kmax. The principle of superposition of fatigue crack growth and static crack growth was used to rationalize the observed crack growth rate response. Static crack growth rate of alloy 718 measured under constant K conditions, was lower than that measured under rising displacement conditions. A crack tip strain rate based model was used to rationalize the fatigue crack growth rate behavior and the static crack growth rate behavior under constant K. However, the formulation of the model for the rising K was not able to rationalize the crack growth rate under rising displacement conditions.

Environmentally Assisted Cracking of Subsea Pipelines in Oil & Gas Production Environments—Effect of Static Loading

CORROSION ◽  
10.5006/2896 ◽  
2020 ◽  
Vol 76 (3) ◽  
pp. 312-323
Author(s):  
Ramgopal Thodla ◽  
Feng Gui ◽  
Colum Holtam
Keyword(s):  
Growth Rate ◽  
Fatigue Crack ◽  
Steady State ◽  
Crack Growth Rate ◽  
Fatigue Crack Growth ◽  
Crack Growth ◽  
Crack Tip ◽  
Metal Dissolution ◽  
Low Frequencies ◽  
Static Crack

Fatigue crack growth rate of line pipe steels in sour environments typically exhibits a steady-state value at low frequencies. However, in highly inhibited sour environments, there is no evidence of a steady-state fatigue crack growth at low frequencies. This is likely a result of static crack growth rate at Kmax. Stable static crack growth measured under constant stress intensity factor (K) conditions in inhibited sour environments was in the range of 10−7 mm/s to 10−8 mm/s. The crack growth rate in inhibited sour environments is likely associated with crack tip processes associated with metal dissolution/film formation and associated hydrogen evolution. The results obtained were modeled based on a crack tip strain rate based approach, where the rate limiting step was the metal dissolution/FeS formation and the corresponding hydrogen generation reaction.

A Modified Engineering Critical Assessment Approach for Offshore Pipelines

2018 ◽  
Author(s):  
Colum Holtam ◽  
Rajil Saraswat ◽  
Ramgopal Thodla ◽  
Feng Gui
Keyword(s):  
Crack Growth ◽  
Low Cycle Fatigue ◽  
Fatigue Loading ◽  
Critical Assessment ◽  
Offshore Pipelines ◽  
Static Crack ◽  
Production Environments ◽  
Assessment Approach ◽  
Girth Welds ◽  
Crack Growth Rates

Environmentally assisted sub-critical static crack growth can occur in offshore pipelines exposed to aggressive production environments. Recent advances in fracture mechanics testing methods have shown that slow static crack growth rates can be reliably measured in sweet and sour environments under constant stress intensity factor (K) conditions. This has potential implications for the engineering critical assessment (ECA) of pipe girth welds subject to low cycle fatigue loading with long periods of operation under constant static load between cycles, e.g. lateral buckling. This paper demonstrates the influence of including static (i.e. time dependent) crack growth as well as fatigue crack growth in a modified pipeline ECA approach.

The relation between the strain energy release in fatigue and quasi-static crack growth

2015 ◽  
Vol 145 ◽  
pp. 86-97 ◽  
Author(s):  
Lucas Amaral ◽  
Liaojun Yao ◽  
René Alderliesten ◽  
Rinze Benedictus
Keyword(s):  
Energy Release ◽  
Crack Growth ◽  
Strain Energy ◽  
Strain Energy Release ◽  
Static Crack

A Finite Element Analysis of Mode III Quasi-Static Crack Growth at a Ductile-Brittle Interface

1996 ◽  
Vol 63 (1) ◽  
pp. 204-209 ◽  
Author(s):  
S. Omprakash ◽  
R. Narasimhan
Keyword(s):  
Finite Element ◽  
Crack Growth ◽  
Power Law ◽  
Plastic Material ◽  
Bimaterial Interface ◽  
Mode Iii ◽  
Elastic Substrate ◽  
Elastic Plastic ◽  
Static Crack ◽  
Elastic Plastic Material

Steady-state quasi-static crack growth along a bimaterial interface is analyzed under Mode III, small-scale yielding conditions using a finite element procedure. The interface is formed by an elastic-plastic material and an elastic substrate. The top elastic-plastic material is assumed to obey the J2 incremental theory of plasticity. It undergoes isotropic hardening with either a bilinear uniaxial response or a power-law response. The results obtained from the full-field numerical analysis compare very well with the analytical asymptotic results obtained by Castan˜eda and Mataga (1991), which forms one of the first studies on this subject. The validity of the separable form for the asymptotic solution assumed in their analysis is investigated. The range of dominance of the asymptotic fields is examined. Field variations are obtained for a power-law hardening elastic-plastic material. It is seen that the stresses are lower for a stiffer substrate. The potential of the bimaterial system to sustain slow stable crack growth along the interface is studied. It is found that the above potential is larger if the elastic substrate is more rigid with respect to the elastic-plastic material.

scholarly journals Frequency Domain Structural Synthesis Applied to Quasi-Static Crack Growth Modeling

2009 ◽  
Vol 16 (6) ◽  
pp. 637-646 ◽  
Author(s):  
Young W. Kwon ◽  
Joshua H. Gordis
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Frequency Domain ◽  
Crack Growth ◽  
Interface Crack ◽  
Composite Beam ◽  
Element Model ◽  
Structural Synthesis ◽  
Synthesis Technique ◽  
Static Crack

Quasi-static crack growth in a composite beam was modeled using the structural synthesis technique along with a finite element model. The considered crack was an interface crack in the shear mode (i.e. mode II), which occurs frequently in the scarf joint of composite structures. The analysis model was a composite beam with an edge crack at the midplane of the beam subjected to a three-point bending load. In the finite element model, beam finite elements with translational degrees of freedom only were used to model the crack conveniently. Then, frequency domain structural synthesis (substructure coupling) was applied to reduce the computational time associated with a repeated finite element calculation with crack growth. The quasi-static interface crack growth in a composite beam was predicted using the developed computational technique, and its result was compared to experimental data. The computational and experimental results agree well. In addition, the substructure-based synthesis technique showed the significantly improved computational efficiency when compared to the conventional full analysis.

Sign in / Sign up

Export Citation Format

Share Document