Relation between the hot gas pressure inside a supernova remnant and its size

2004 ◽  
Vol 33 (4) ◽  
pp. 416-421 ◽  
Author(s):  
H Tsunemi ◽  
H Enoguchi
2012 ◽  
Vol 735 ◽  
pp. 198-203 ◽  
Author(s):  
Alexander J. Carpenter ◽  
Eric M. Taleff ◽  
Louis G. Hector ◽  
Jon T. Carter ◽  
Paul E. Krajewski

A time-dependent material constitutive model is developed for the deformation of wrought Mg AZ31 sheet material at 450°C. This material model is used to simulate gas-pressure bulge forming of AZ31 sheet into hemispherical domes. Finite-element-method (FEM) simulations using this material model are compared against experimental data obtained for dome height as a function of forming time under forming conditions identical to those assumed in the simulations. The time-dependent material model predicts experimental dome heights during forming with a quite useful accuracy. The most significant advantage of the time-dependent material model is that it can address the effect of preheating time on forming. Preheating times shorter than ~120 s produce an increase in forming rate. This material model provides a quantitative means of accounting for that effect.


Author(s):  
Eric M. Taleff ◽  
Louis G. Hector ◽  
John R. Bradley ◽  
Ravi Verma ◽  
Paul E. Krajewski

Splitting at regions of local thinning below die entry radii is a critically important mechanism of failure in hot gas-pressure forming of sheet materials. Local thinning is controlled by sheet-die friction and die geometry, as well as sheet material properties. In this study, local thinning is investigated at a particularly severe die entry radius during hot forming of a fine-grained AA5083 sheet at 450°C. Particular emphasis is placed on the relationship between local thinning and sheet-die friction conditions. A simple analysis of the mechanics of this thinning phenomenon is presented. Finite element simulation results are presented for different sheet-die friction conditions. Sheet thickness profiles measured from parts produced in forming experiments using three different lubrication conditions are compared with predictions from simulations. Simulation predictions agree well with experimental data for the occurrence and location of thinning below a die entry radius. Additional insights into sheet-die friction for controlling local thinning and preventing premature necking failure are detailed.


1988 ◽  
Vol 101 ◽  
pp. 257-260
Author(s):  
K. Tatematsu ◽  
Y. Fukui ◽  
T. Iwata ◽  
M. Nakano

AbstractWe observed the semicircular supernova remnant G109.1-1.0 in the J = 1-0 transition of CO with the Nobeyama 45-m radio telescope. It is found that two remarkably thin molecular filaments delineate the inner boundary of the X-ray jet feature in this remnant. These filaments seem to have experienced evaporation due to the hot gas in the remnant.


1988 ◽  
Vol 101 ◽  
pp. 205-222 ◽  
Author(s):  
Christopher F. McKee

AbstractThe inhomogeneity of the interstellar medium (ISM) has a profound effect on the propagation of the interstellar shock generated by a supernova and on the appearance of the resulting supernova remnant (SNR). Low mass supernovae produce remnants that interact with the “pristine” ISM, which has density inhomogeneities (clouds) on a wide range of scales. The shock compresses and accelerates the clouds it encounters; inside the blast wave, the clouds are hydrodynamically unstable, and mass is injected from the clouds into the intercloud medium. Embedded clouds interact thermally with the shock also, adding mass to the hot intercloud medium via thermal evaporation or subtracting it via condensation and thermal instability. Mass injection into the hot intercloud medium, whether dynamical or thermal, leads to infrared emission as dust mixes with the hot gas and is thermally sputtered. The remnants of massive supernovae interact primarily with circumstellar matter and with interstellar material which has been processed by the ionizing radiation and wind of the progenitor star. After passing through any circumstellar material which may be present, the shock encounters a cavity which tends to “muffle” the SNR. The remnants of massive supernovae therefore tell us more about the late stages of the evolution of massive stars than about the ISM.


2014 ◽  
Vol 53 (20) ◽  
pp. 8599-8607 ◽  
Author(s):  
Yujun Liu ◽  
Shawn D. Feist ◽  
Christopher M. Jones ◽  
Daniel R. Armstrong

2010 ◽  
Vol 433 ◽  
pp. 185-195 ◽  
Author(s):  
Paul A. Sherek ◽  
Louis G. Hector ◽  
John R. Bradley ◽  
Paul E. Krajewski ◽  
Eric M. Taleff

Accurate numerical simulation capability is critical to the development and implementation of hot forming technologies. Numerical simulations were developed for gas-pressure forming of commercial, fine-grained aluminum-magnesium (AA5083) material into deep pan shapes at 450°C. These simulations utilize a material constitutive model recently developed for fine-grained AA5083 materials as a user-defined routine in commercial Finite Element Method (FEM) software. Results from simulations are compared against data from gas-pressure forming experiments, which used the same forming conditions and die geometries. Specifically, local sheet thinning and radius of curvature in edges and corners are compared between simulation and experiment. Numerical simulations are in good agreement with experiments for local sheet thinning of up to 50%. For locations where sheet thinning exceeds 50%, simulations predict less thinning and larger formed radii than observed in experiments. It is likely that cavitation, which is not accounted for in simulations, plays a significant role in causing a decrease in simulation prediction accuracy for thinning values greater than 50%. This study demonstrates a simulation capability that is potentially of significant practical use for predicting the hot gas-pressure forming of fine-grained AA5083 material.


Sign in / Sign up

Export Citation Format

Share Document