Experimental analysis and modelling of mechanical properties and shrinkage of concrete recycling flash calcined dredging sediments

2021 ◽  
Vol 115 ◽  
pp. 103787
Author(s):  
Céline Van Bunderen ◽  
Farid Benboudjema ◽  
Ruben Snellings ◽  
Lucie Vandewalle ◽  
Özlem Cizer
2011 ◽  
Vol 415-417 ◽  
pp. 2338-2344
Author(s):  
Xin Shen Huang ◽  
Qun Gao ◽  
Zhi Jian Zong

Different laid modes of aluminum alloy section bars and their mortise and tenon joints were bending tested, and their mechanical properties were compared, in order to research on the influence that forming a mortise and tenon joint brought to the original bars. Opening a hole laterally and inserting another shorter bar in the hole changed the bending properties and energy absorption capacity of the original bar. In horizontal laid mode, the mortise and tenon joint was weaker than the original bar when bearing bending load, but it was stronger in vertical laid mode. Weld beads of the mortise and tenon joints were strong enough to maintain the structure integrality before the main section bars were destroyed by load.


2018 ◽  
Vol 149 ◽  
pp. 01026
Author(s):  
Taieb Fatima ◽  
Belas Nadia ◽  
Belaribi Omar ◽  
Belguesmia Khalil ◽  
Hadj Sadok Rachid

The use of SCC has a particular interest in terms of sustainable development. Indeed, their specific formulation leads to a greater volume of dough than for common concretes, thus, a larger quantity of cement. However, for economical, ecological and technical reasons, it is sought to limit their cement content [1]. It is therefore necessary to almost always use mineral additions as a partial replacement for cement because the technology of self-compacting concretes can consume large quantities of fines, in this case calcinated mud issued from dams dredging sediments that can give and/or ameliorate characteristics and performances of this type of concretes. Four SCCs had been formulated from the same composition where the only percentage of calcinated mud of Chorfa (west of Algeria) dam changed (0%, 10%, 20% and 30%). The effect of calcinated mud on characteristics at fresh state of SCC according to AFGC was quantified. Mechanical strengths and shrinkage deformation (total, autogenous, drying) were evaluated. The results show the possibility to make SCCs with different dosages of calcinated mud having strengths that can defy those of the control SCC. The analysis of free deformations indicates the beneficial impact of the mud by contributing to decrease the amplitudes of the shrinkage compared to those of the control SCC.


2016 ◽  
Vol 89 ◽  
pp. 01004
Author(s):  
Martin Bílek ◽  
Šimon Kovář ◽  
Eva Moučková ◽  
Petr Tumajer

2013 ◽  
Vol 550 ◽  
pp. 9-16
Author(s):  
Kamal Ait Tahar ◽  
R. Bahar

Currently, the composite materials make important great strides, considering their high mechanical properties. The studies relating to the conceptual, technical aspect and modeling of their mechanical behavior are more than desirable. The mechanical properties of the composite material depend on several factors as the nature of fibers, the fiber/matrix ratio, compatibility, homogeneity... In this study, we present the results of an experimental analysis of the behavior of the composite material, under a static and a dynamic loading. The composite material is composed respectively of the glass and metal fiber reinforcement. A various dimensions of the mesh are considering. The resin used is polyester Resow 55 E. The dynamic test ( Knoop test) is carried out on various specimens made up of an polyester resin RESOW 55 E reinforced with varied powder nature. It makes it possible to measure the hardness of composite materials. The analysis of the results shows clearly that the mechanical properties are strongly influenced by the dimensions of the elementary mesh of the fiber grid reinforcement. Based on experimental results, a Weibull modulus has been established for each specimen.


2016 ◽  
Vol 11 (39) ◽  
pp. 181-190
Author(s):  
He Xiao ◽  
Li Qing ◽  
Chen Hongkai ◽  
Tang Hongmei ◽  
Wang Linfeng

Sign in / Sign up

Export Citation Format

Share Document