THERMODYNAMIC ANALYSIS OF FUEL OIL BLENDED STOCK (FOBS) MODEL COMPOUND, n-EICOSANE TO HYDROGEN VIA OXIDATIVE CRACKING

Author(s):  
Mei Lian Teo ◽  
Mazura Jusoh ◽  
Zaki Yamani Zakaria
Author(s):  
Liping Liu ◽  
Yingfan Li ◽  
Yu Cui ◽  
Shuqi Fang ◽  
Kai Wang ◽  
...  

2021 ◽  
Vol 14 (02) ◽  
pp. 1065-1071
Author(s):  
T.V. Shakiyeva ◽  
L.R. Sassykova ◽  
U. N. Dzhatkambayeva ◽  
A.A. Khamlenko ◽  
N.K. Zhakirova ◽  
...  

Author(s):  
S. Brusca ◽  
R. Lanzafame

A mathematical model of a heavy duty gas turbine has been implemented using GateCycle™ code. This model is able to simulate the engine behavior running on syngas and fuel oil. Also engine control logic is implemented using Microsoft Excel™ VBA language. The model implemented has been finely tuned and tested with measured data. Test results show that it is able to simulate engine running in on-design and off-design conditions. Using this model, an extensive thermodynamic analysis of light fuel oil and syngas fed engine performance has been carried out in respect of ambient conditions. As it is possible to see in the results of the thermodynamic analysis, at high air temperatures performance reduction occur. Relative humidity have a slightly effect on engine performance when the latter is running on syngas. Instead it doesn’t have a relevant effect on the performance of the engine running on light liquid fuel oil in all the range of ambient temperature investigated. Results of this analysis also show the correct replication of the engine control system. In conclusion, the developed mathematical model is able to simulate gas turbine operations with low errors. So that, it could be used in order to optimise engine performance at the ambient conditions that occur for the site of the IGCC Complex in which gas turbine has integrated as topper.


Author(s):  
J.K. Lampert ◽  
G.S. Koermer ◽  
J.M. Macaoy ◽  
J.M. Chabala ◽  
R. Levi-Setti

We have used high spatial resolution imaging secondary ion mass spectrometry (SIMS) to differentiate mineralogical phases and to investigate chemical segregations in fluidized catalytic cracking (FCC) catalyst particles. The oil industry relies on heterogeneous catalysis using these catalysts to convert heavy hydrocarbon fractions into high quality gasoline and fuel oil components. Catalyst performance is strongly influenced by catalyst microstructure and composition, with different chemical reactions occurring at specific types of sites within the particle. The zeolitic portions of the particle, where the majority of the oil conversion occurs, can be clearly distinguished from the surrounding silica-alumina matrix in analytical SIMS images.The University of Chicago scanning ion microprobe (SIM) employed in this study has been described previously. For these analyses, the instrument was operated with a 40 keV, 10 pA Ga+ primary ion probe focused to a 30 nm FWHM spot. Elemental SIMS maps were obtained from 10×10 μm2 areas in times not exceeding 524s.


2001 ◽  
Vol 268 (6) ◽  
pp. 1554-1560 ◽  
Author(s):  
Reinskje Talhout ◽  
Jan B. F. N. Engberts

1997 ◽  
Vol 9 (6) ◽  
pp. 541-565 ◽  
Author(s):  
Cheryl R. Killingsworth ◽  
Francesca Alessandrini ◽  
G. G. Krishna Murthy ◽  
Paul J. Catalano ◽  
Joseph D. Paulauskis ◽  
...  

1913 ◽  
Vol 76 (1960supp) ◽  
pp. 61-64
Author(s):  
C. F. Hirshfeld
Keyword(s):  

2015 ◽  
Vol 1 (1) ◽  
pp. 5-16
Author(s):  
John Ohoiwutun

Utilization of conventional energy sources such as coal, fuel oil, natural gas and others on the one hand has a low operating cost, but on the other side of the barriers is the greater source of diminishing returns and, more importantly, the emergence of environmental pollution problems dangerous to human life. This study aims to formulate the kinematics and dynamics to determine the movement of Solar Power Mower. In this study, using solar power as an energy source to charge the battery which then runs the robot. Design and research was conducted in the Department of Mechanical Workshop Faculty of Engineering, University of Hasanuddin of Gowa. Control system used is a manual system using radio wave transmitter and receiver which in turn drive the robot in the direction intended. Experimental results showed that treatment with three variations of the speed of 6.63 m / s, 8.84 m / s and 15.89 m / sec then obtained the best results occur in grass cutting 15.89 sec and high-speed cutting grass 5 cm. Formulation of kinematics and dynamics for lawn mowers, there are 2 control input variables, x and y ̇ ̇ 3 to control the output variables x, y and θ so that there is one variable redudant. Keywords: mobile robots, lawn mower, solar power


Sign in / Sign up

Export Citation Format

Share Document