Multi-objective optimisation and fast decision-making method for working fluid selection in organic Rankine cycle with low-temperature waste heat source in industry

2018 ◽  
Vol 172 ◽  
pp. 200-211 ◽  
Author(s):  
Xu Zhang ◽  
Hao Bai ◽  
Xiancong Zhao ◽  
Ali Diabat ◽  
Jian Zhang ◽  
...  
Keyword(s):  
Decision Making ◽  
Low Temperature ◽  
Heat Source ◽  
Waste Heat ◽  
Organic Rankine Cycle ◽  
Rankine Cycle ◽  
Working Fluid ◽  
Multi Objective ◽  
Working Fluid Selection ◽  
Fast Decision

scholarly journals Configuration Selection of the Multi-Loop Organic Rankine Cycle for Recovering Energy from a Single Source

Entropy ◽  
2021 ◽  
Vol 23 (11) ◽  
pp. 1435
Author(s):  
Youyi Li ◽  
Tianhao Tang
Keyword(s):  
Heat Source ◽  
Waste Heat ◽  
Organic Rankine Cycle ◽  
Optimal Solution ◽  
Rankine Cycle ◽  
Optimal Number ◽  
Exergy Efficiency ◽  
Working Fluid ◽  
Levelized Cost Of Electricity ◽  
Multi Objective

The Organic Rankine Cycle (ORC) is a well-established way to recover energy from a single waste heat source. This paper aims to select the suitable configuration, number of loops, and working fluids for the Multi-Loop ORC (MLORC) by using multi-objective optimization. The thermodynamic and economic performance of MLORC in three various configurations was analyzed. Multi-objective optimizations of the series and parallel MLORC using different working fluid groups were conducted to find the optimal configuration, number of loops, and working fluid combination. The analysis results show that the series–parallel MLORC performed the worst among the three configurations. The optimization results reveal that series MLORC has a higher exergy efficiency than the parallel MLORC. The exergy efficiency of the optimal solution in series dual-loop, triple-loop, and quadruple-loop ORC is 9.3%, 7.98%, and 6.23% higher than that of parallel ORC, respectively. Furthermore, dual-loop is the optimal number of cycles for recovering energy from a single heat source, according to the grey relational grade. Finally, the series dual-loop ORC using cyclohexane\cyclohexane was the suitable configuration for utilizing a single waste heat source. The exergy efficiency and levelized cost of electricity of the series dual-loop ORC with the optimal parameters are 62.18% and 0.1509 $/kWh, respectively.

A Computer Program for Working Fluid Selection of Low Temperature Organic Rankine Cycle

2015 ◽  
Author(s):  
Muhammad Ansab Ali ◽  
Tariq Saeed Khan ◽  
Ebrahim Al Hajri ◽  
Zahid H. Ayub
Keyword(s):  
Low Temperature ◽  
Heat Source ◽  
Computer Program ◽  
Fossil Fuels ◽  
Waste Heat ◽  
Organic Rankine Cycle ◽  
Rankine Cycle ◽  
Power Production ◽  
Working Fluid ◽  
Low Grade

Fossil fuels are continuously depleting while the global energy demand is growing at a fast rate. Additionally, fossil fuels based power plants contribute to environmental pollution. Search for alternate energy resources and use of industrial waste heat for power production are attractive topics of interest these days. One way of enhancing power production and decreasing the environmental impact is by recuperating and utilizing low grade thermal energy. In recent years, research on use of organic Rankine cycle (ORC) has gained popularity as a promising technology for conversion of heat into useful work or electricity. Due to simple structure of ORC system, it can be easily integrated with any energy source like geothermal energy, solar energy and waste heat. A computer program has been developed in engineering equation solver (EES) environment that analyzes and selects appropriate working fluid for organic Rankine cycle design based on available heat sources. For a given heat source, the program compares energy and exergy performance of various working fluids. The program also includes recuperator performance analysis and compares its effectiveness on the overall thermal performance of the Rankine cycle. This program can assist in preliminary design of ORC with respect to best performing refrigerant fluid selection for the given low temperature heat source.

Working Fluid Selection for an Organic Rankine Cycle for Waste Heat Recovery under Different Heat Source Temperatures

2013 ◽  
Vol 732-733 ◽  
pp. 213-217 ◽  
Author(s):  
Shuang Yang ◽  
Bing Zhang ◽  
Jin Liang Xu ◽  
Wei Zhang ◽  
Chao Xian Wang
Keyword(s):  
Heat Source ◽  
Waste Heat ◽  
Organic Rankine Cycle ◽  
Rankine Cycle ◽  
Operating Conditions ◽  
Working Fluid ◽  
Working Fluids ◽  
Working Fluid Selection ◽  
Cycle Efficiency ◽  
Optimum Working

Optimum working conditions of 11 working fluids under different heat source temperatures in an organic Rankine cycle were systematically investigated. Cycle efficiency of each fluid was compared at their optimal operating conditions were then analyzed. R141b appears to be the best choice when the heat source temperature is around 200oC. Heptane is suggested the suitable working fluids for the ORC system when the heat source is 300oC.

Theoretical and experimental investigation of an organic Rankine cycle for a waste heat recovery system

2009 ◽  
Vol 223 (5) ◽  
pp. 523-533 ◽  
Author(s):  
W Gu ◽  
Y Weng ◽  
Y Wang ◽  
B Zheng
Keyword(s):  
Heat Source ◽  
Entropy Generation ◽  
Waste Heat ◽  
Organic Rankine Cycle ◽  
Rankine Cycle ◽  
Entropy Generation Rate ◽  
Working Fluid ◽  
Total Entropy ◽  
Waste Heat Recovery System ◽  
Cycle Efficiency

This article describes and evaluates an organic Rankine cycle (ORC) for a waste heat recovery system by both theoretical and experimental studies. Theoretical analysis of several working fluids shows that cycle efficiency is very sensitive to evaporating pressure, but insensitive to expander inlet temperature. Second law analysis was carried out using R600a as a working fluid and a flow of hot air as a heat source, which is not isothermal, along the evaporator. The result discloses that the evaporator's internal and external entropy generation is the main source of total entropy generation. The effect of the heat source temperature, evaporating pressure, and evaporator size on the entropy generation rate is also presented. The obtained useful power is directly linked to the total entropy generation rate according to the Gouy—Stodola theorem. The ORC testing system was established and operated using R600a as a working fluid and hot water as a heat source. The maximum cycle efficiency of the testing system is 5.2 per cent, and the testing result also proves that cycle efficiency is insensitive to heat source temperature, but sensitive to evaporating pressure. The entropy result also shows that internal and external entropy of the evaporator is the main source of total entropy generation.

Calculation and Optimization of Heat Transfer between the Low Exergy Heat Source and Organic Rankine Cycle Applied to Heat Recovery Systems

2013 ◽  
Vol 597 ◽  
pp. 45-50
Author(s):  
Sławomir Smoleń ◽  
Hendrik Boertz
Keyword(s):  
Heat Transfer ◽  
Heat Source ◽  
Heat Recovery ◽  
Power Plants ◽  
Waste Heat ◽  
Organic Rankine Cycle ◽  
Optimization Procedure ◽  
Rankine Cycle ◽  
Working Fluid ◽  
Total System

One of the key challenges on the area of energy engineering is the system development for increasing the efficiency of primary energy conversion and use. An effective and important measure suitable for improving efficiencies of existing applications and allowing the extraction of energy from previously unsuitable sources is the Organic Rankine Cycle. Applications based on this cycle allow the use of low temperature energy sources such as waste heat from industrial applications, geothermal sources, biomass, fired power plants and micro combined heat and power systems.Working fluid selection is a major step in designing heat recovery systems based on the Organic Rankine Cycle. Within the framework of the previous original study a special tool has been elaborated in order to compare the influence of different working fluids on performance of an ORC heat recovery power plant installation. A database of a number of organic fluids has been developed. The elaborated tool should create a support by choosing an optimal working fluid for special applications and become a part of a bigger optimization procedure by different frame conditions. The main sorting criterion for the fluids is the system efficiency (resulting from the thermo-physical characteristics) and beyond that the date base contains additional information and criteria, which have to be taken into account, like environmental characteristics for safety and practical considerations.The presented work focuses on the calculation and optimization procedure related to the coupling heat source – ORC cycle. This interface is (or can be) a big source of energy but especially exergy losses. That is why the optimization of the heat transfer between the heat source and the process is (besides the ORC efficiency) of essential importance for the total system efficiency.Within the presented work the general calculation approach and some representative calculation results have been given. This procedure is a part of a complex procedure and program for Working Fluid Selection for Organic Rankine Cycle Applied to Heat Recovery Systems.

Exergoeconomic comparison and optimization of organic Rankine cycle, trilateral Rankine cycle and transcritical carbon dioxide cycle for heat recovery of low-temperature geothermal water

2019 ◽  
Vol 233 (8) ◽  
pp. 1068-1084 ◽  
Author(s):  
Afsaneh Noroozian ◽  
Abbas Naeimi ◽  
Mokhtar Bidi ◽  
Mohammad Hossein Ahmadi
Keyword(s):  
Sensitivity Analysis ◽  
Low Temperature ◽  
Heat Source ◽  
Organic Rankine Cycle ◽  
Rankine Cycle ◽  
Working Fluid ◽  
Cost Ratio ◽  
Exergetic Efficiency ◽  
Geothermal Heat ◽  
Product Cost

Depleting fossil fuel resources and the horrible environmental impacts due to burning fossil fuels emphasize the importance of using renewable energy resources such as geothermal and solar energies. This paper compares performance of CO2 transcritical cycle, organic Rankine cycle, and trilateral Rankine cycle using a low-temperature geothermal heat source. Thermodynamic analysis, exergetic analysis, economic analysis, and exergoeconomic analysis are applied for each of the aforementioned cycles. In addition, a sensitivity analysis is performed on the system, and the effects of geothermal heat source temperature, evaporator pinch point temperature, and turbine inlet pressure on the cycle's performance are evaluated. Finally, the systems are optimized in order to minimize product cost ratio and maximize exergetic efficiency by using the genetic algorithm. Results indicate that the maximum thermal efficiency is approximately 13.03% which belongs to organic Rankine cycle with R123 as working fluid. CO2 cycle has the maximum exergetic efficiency, equals to 46.13%. The minimum product cost ratio refers to the organic Rankine cycle with R245fa as working fluid. Moreover, sensitivity analysis shows that increasing geothermal heat source temperature results in higher output power, product cost ratio, and exergy destruction ratio in all cycles.

Performance Investigation of Solar Organic Rankine Cycle Systems With and Without Regeneration and With Zeotropic Working Fluid Mixtures for Use in Micro-Cogeneration

2020 ◽  
Author(s):  
Wahiba Yaïci ◽  
Evgueniy Entchev ◽  
Pouyan Talebizadeh Sardari
Keyword(s):  
Low Temperature ◽  
Heat Source ◽  
High Efficiency ◽  
Organic Rankine Cycle ◽  
Rankine Cycle ◽  
Industrial Wastes ◽  
Working Fluid ◽  
Condensation Temperature ◽  
Thermodynamic Performance ◽  
Cycle Efficiency

Abstract Globally there are several viable sources of renewable, low-temperature heat (below 130°C) particularly solar energy, geothermal energy, and energy generated from industrial wastes. Increased exploitation of these low-temperature options has the definite potential of reducing fossil fuel consumption with its attendant very harmful greenhouse gas emissions. Researchers have universally identified the organic Rankine cycle (ORC) as a practicable and promising system to generate electrical power from renewable sources based on its beneficial use of volatile organic fluids as working fluids (WFs). In recent times, researchers have also shown a preference for/an inclination towards deployment of zeotropic mixtures as ORC WFs because of their capacity to improve thermodynamic performance of ORC systems, a feat enabled by better matches of the temperature profiles of the WF and the heat source/sink. This paper demonstrates both the technical feasibility and the notable advantages of using zeotropic mixtures as WFs through a simulation study of an ORC system. The study examines the thermodynamic performance of ORC systems using zeotropic WF mixtures to generate electricity driven by low-temperature solar heat source for building applications. A thermodynamic model is developed with an ORC system both with and excluding a regenerator. Five zeotropic mixtures with varying compositions of R245fa/propane, R245fa/hexane, R245fa/heptane, pentane/hexane and isopentane/hexane are evaluated and compared to identify the best combinations of WF mixtures that can yield high efficiency in their system cycles. The study also investigates the effects of the volumetric flow ratio, and evaporation and condensation temperature glides on the ORC’s thermodynamic performance. Following a detailed analysis of each mixture, R245fa/propane is selected for parametric study to examine the effects of operating parameters on the system’s efficiency and sustainability index. For zeotropic mixtures, results showed that there is an optimal composition range within which binary mixtures are inclined to perform more efficiently than the component pure fluids. In addition, a significant increase in cycle efficiency can be achieved with a regenerative ORC, with cycle efficiency ranging between 3.1–9.8% and 8.6–17.4% for ORC both without and with regeneration, respectively. Results also showed that exploiting zeotropic mixtures could enlarge the limitation experienced in selecting WFs for low-temperature solar organic Rankine cycles.

scholarly journals Multi-objective optimization of CuO based organic Rankine cycle operated using R245ca

2019 ◽  
Vol 116 ◽  
pp. 00062 ◽  
Author(s):  
Parth Prajapati ◽  
Vivek Patel
Keyword(s):  
Heat Transfer ◽  
Thermal Efficiency ◽  
Heat Exchangers ◽  
Waste Heat ◽  
Organic Rankine Cycle ◽  
Rankine Cycle ◽  
Working Fluid ◽  
Multi Objective Optimization ◽  
Multi Objective ◽  
Source Fluid

The present work deals with multi objective optimization of nanofluid based Organic Rankine Cycle (ORC) to utilise waste heat energy. Working fluid considered for the study is R245ca for its good thermodynamic properties and lower Global Warming Potential (GWP) compared to the conventional fluids used in the waste heat recovery system. Heat Transfer Search (HTS) algorithm is used to optimize the objective functions which tends to maximize thermal efficiency and minimize Levelised Energy Cost (LEC). To enhance heat transfer between the working fluid and source fluid, nanoparticles are added to the source fluid. Application of nanofluids in the heat transfer system helps in maximizing recovery of the waste heat in the heat exchangers. Based on the availability and cost, CuO nanoparticles are considered for the study. Effect of Pinch Point Temperature Difference (PPTD) and concentration of nanoparticles in heat exchangers is studied and discussed. Results showed that nanofluids based ORC gives maximum thermal efficiency of 18.50% at LEC of 2.59 $/kWh. Total reduction of 7.11% in LEC can be achieved using nanofluids.

scholarly journals A Simple Method of Finding New Dry and Isentropic Working Fluids for Organic Rankine Cycle

Energies ◽  
2019 ◽  
Vol 12 (3) ◽  
pp. 480 ◽  
Author(s):  
Gábor Györke ◽  
Axel Groniewsky ◽  
Attila Imre
Keyword(s):  
Low Temperature ◽  
Waste Heat ◽  
Organic Rankine Cycle ◽  
Rankine Cycle ◽  
Electricity Production ◽  
Working Fluid ◽  
Heat Sources ◽  
Simple Method ◽  
Working Fluids ◽  
Temperature Heat

One of the most crucial challenges of sustainable development is the use of low-temperature heat sources (60–200 °C), such as thermal solar, geothermal, biomass, or waste heat, for electricity production. Since conventional water-based thermodynamic cycles are not suitable in this temperature range or at least operate with very low efficiency, other working fluids need to be applied. Organic Rankine Cycle (ORC) uses organic working fluids, which results in higher thermal efficiency for low-temperature heat sources. Traditionally, new working fluids are found using a trial-and-error procedure through experience among chemically similar materials. This approach, however, carries a high risk of excluding the ideal working fluid. Therefore, a new method and a simple rule of thumb—based on a correlation related to molar isochoric specific heat capacity of saturated vapor states—were developed. With the application of this thumb rule, novel isentropic and dry working fluids can be found applicable for given low-temperature heat sources. Additionally, the importance of molar quantities—usually ignored by energy engineers—was demonstrated.

Sign in / Sign up

Export Citation Format

Share Document