Investigation on Filippi’s stress equation for V-shaped notch with rounded vertex Part II: Mode II stresses

2017 ◽  
Vol 178 ◽  
pp. 318-332 ◽  
Author(s):  
D.H. Chen
Keyword(s):  
Mode Ii ◽  
2016 ◽  
Vol 58 (4) ◽  
pp. 374-380 ◽  
Author(s):  
Mohd Azwan Husin ◽  
Rozli Zulkifli ◽  
Shahrum Abdullah ◽  
Wan Ramli Wan Daud
Keyword(s):  

2021 ◽  
Vol 28 (1) ◽  
pp. 382-393
Author(s):  
Mazaher Salamt-Talab ◽  
Fatemeh Delzendehrooy ◽  
Alireza Akhavan-Safar ◽  
Mahdi Safari ◽  
Hossein Bahrami-Manesh ◽  
...  

Abstract In this article, mode II fracture toughness ( G IIc {G}_{\text{IIc}} ) of unidirectional E-glass/vinyl ester composites subjected to sulfuric acid aging is studied at two different temperatures (25 and 90°C). Specimens were manufactured using the hand lay-up method with the [ 0 ] 20 {{[}0]}_{20} stacking sequence. To study the effects of environmental conditions, samples were exposed to 30 wt% sulfuric acid at room temperature (25°C) for 0, 1, 2, 4, and 8 weeks. Some samples were also placed in the same solution but at 90°C and for 3, 6, 9, and 12 days to determine the interlaminar fracture toughness at different aging conditions. Fracture tests were conducted using end notched flexure (ENF) specimens according to ASTM D7905. The results obtained at 25°C showed that mode II fracture toughness increases for the first 2 weeks of aging and then it decreases for the last 8 weeks. It was also found that the flexural modulus changes with the same trend. Based on the results of the specimens aged at 90°C, a sharp drop in fracture toughness and flexural modulus with a significant decrease in maximum load have been observed due to the aging. Finite element simulations were performed using the cohesive zone model (CZM) to predict the global response of the tested beams.


Polymers ◽  
2021 ◽  
Vol 13 (4) ◽  
pp. 492
Author(s):  
Zhen Pei Chow ◽  
Zaini Ahmad ◽  
King Jye Wong ◽  
Seyed Saeid Rahimian Koloor ◽  
Michal Petrů

This paper aims to propose a temperature-dependent cohesive model to predict the delamination of dissimilar metal–composite material hybrid under Mode-I and Mode-II delamination. Commercial nonlinear finite element (FE) code LS-DYNA was used to simulate the material and cohesive model of hybrid aluminium–glass fibre-reinforced polymer (GFRP) laminate. For an accurate representation of the Mode-I and Mode-II delamination between aluminium and GFRP laminates, cohesive zone modelling with bilinear traction separation law was implemented. Cohesive zone properties at different temperatures were obtained by applying trends of experimental results from double cantilever beam and end notched flexural tests. Results from experimental tests were compared with simulation results at 30, 70 and 110 °C to verify the validity of the model. Mode-I and Mode-II FE models compared to experimental tests show a good correlation of 5.73% and 7.26% discrepancy, respectively. Crack front stress distribution at 30 °C is characterised by a smooth gradual decrease in Mode-I stress from the centre to the edge of the specimen. At 70 °C, the entire crack front reaches the maximum Mode-I stress with the exception of much lower stress build-up at the specimen’s edge. On the other hand, the Mode-II stress increases progressively from the centre to the edge at 30 °C. At 70 °C, uniform low stress is built up along the crack front with the exception of significantly higher stress concentrated only at the free edge. At 110 °C, the stress distribution for both modes transforms back to the similar profile, as observed in the 30 °C case.


2021 ◽  
Vol 147 (2) ◽  
pp. 07020003
Author(s):  
Sakineh Fazli Ghiyasabadi ◽  
Ehsan Nikooee ◽  
Ghassem Habibagahi

2021 ◽  
Author(s):  
Francisco Maciel Monticeli ◽  
Midori Yoshikawa Pitanga ◽  
Maria Odila Hilário Cioffi ◽  
Herman Jacobus Cornelis Voorwald
Keyword(s):  
Mode I ◽  

Sign in / Sign up

Export Citation Format

Share Document