Feasibility evaluation of gas-assisted heating for mold surface temperature control during injection molding process

2009 ◽  
Vol 36 (8) ◽  
pp. 806-812 ◽  
Author(s):  
Shia-Chung Chen ◽  
Rean-Der Chien ◽  
Su-Hsia Lin ◽  
Ming-Chung Lin ◽  
Jen-An Chang
Keyword(s):  
Injection Molding ◽  
Surface Temperature ◽  
Temperature Control ◽  
Injection Molding Process ◽  
Mold Surface ◽  
Molding Process ◽  
Feasibility Evaluation

scholarly journals Study on External Gas-Assisted Mold Temperature Control for Improving the Melt Flow Length of Thin Rib Products in the Injection Molding Process

2019 ◽  
Vol 2019 ◽  
pp. 1-17 ◽  
Author(s):  
Phan The Nhan ◽  
Thanh Trung Do ◽  
Tran Anh Son ◽  
Pham Son Minh
Keyword(s):  
Injection Molding ◽  
Temperature Control ◽  
High Efficiency ◽  
Mold Temperature ◽  
Injection Molding Process ◽  
Thin Wall ◽  
Mold Surface ◽  
Melt Flow ◽  
Molding Process ◽  
Flow Length

In the injection molding process, mold temperature control is one of the most efficient methods for improving product quality. In this research, an external gas-assisted mold temperature control (Ex-GMTC) with gas temperature variation from 200°C to 400°C was applied to thin wall injection molding at melt thicknesses from 0.2 to 0.6 mm. The melt flow length was evaluated through the application of this system to the mold of a thin rib product. The results show that the heating process achieves high efficiency in the initial 20 s, with a maximum heating rate of 6.4°C/s. In this case, the mold surface reached 158.4°C. By applying Ex-GMTC to a 0.2 mm flow thickness, the flow length increased from 37.85 to 41.32 mm with polypropylene (PP) material and from 14.54 to 15.8 mm with acrylonitrile butadiene styrene (ABS) material. With the thin rib mold and use of Ex-GMTC, the mold temperature varied from 112.0°C to 140.8°C and the thin rib height reached 7.0 mm.

scholarly journals Hierarchical Structure of iPP During Injection Molding Process with Fast Mold Temperature Evolution

Materials ◽  
2019 ◽  
Vol 12 (3) ◽  
pp. 424 ◽  
Author(s):  
Vito Speranza ◽  
Sara Liparoti ◽  
Roberto Pantani ◽  
Giuseppe Titomanlio
Keyword(s):  
Injection Molding ◽  
Surface Temperature ◽  
Hierarchical Structure ◽  
Flow Fields ◽  
Electrical Heating ◽  
Cavity Surface ◽  
Injection Molding Process ◽  
Mold Surface ◽  
Molding Process ◽  
Injection Molded

Mold surface temperature strongly influences the molecular orientation and morphology developed in injection molded samples. In this work, an isotactic polypropylene was injected into a rectangular mold, in which the cavity surface temperature was properly modulated during the process by an electrical heating device. The induced thermo-mechanical histories strongly influenced the morphology developed in the injection molded parts. Polarized optical microscope and atomic force microscope were adopted for morphological investigations. The combination of flow field and cooling rate experienced by the polymer determined the hierarchical structure. Under strong flow fields and high temperatures, a tightly packed structure, called shish-kebab, aligned along the flow direction, was observed. Under weak flow fields, the formation of β-phase, as cylindrites form, was observed. The formation of each morphological structure was analyzed and discussed on the bases of the flow and temperature fields, experienced by the polymer during each stage of the injection molding process.

scholarly journals Study on External Gas-Assisted Mold Temperature Control with the Assistance of a Flow Focusing Device in the Injection Molding Process

Materials ◽  
2021 ◽  
Vol 14 (4) ◽  
pp. 965 ◽  
Author(s):  
Nguyen Truong Giang ◽  
Pham Son Minh ◽  
Tran Anh Son ◽  
Tran Minh The Uyen ◽  
Thanh-Hai Nguyen ◽  
...  
Keyword(s):  
Injection Molding ◽  
Temperature Control ◽  
Mold Temperature ◽  
Injection Molding Process ◽  
Melt Flow ◽  
Flow Focusing ◽  
Molding Process ◽  
Heating Efficiency ◽  
Flow Length ◽  
Insert Plate

In the injection molding field, the flow of plastic material is one of the most important issues, especially regarding the ability of melted plastic to fill the thin walls of products. To improve the melt flow length, a high mold temperature was applied with pre-heating of the cavity surface. In this paper, we present our research on the injection molding process with pre-heating by external gas-assisted mold temperature control. After this, we observed an improvement in the melt flow length into thin-walled products due to the high mold temperature during the filling step. In addition, to develop the heating efficiency, a flow focusing device (FFD) was applied and verified. The simulations and experiments were carried out within an air temperature of 400 °C and heating time of 20 s to investigate a flow focusing device to assist with external gas-assisted mold temperature control (Ex-GMTC), with the application of various FFD types for the temperature distribution of the insert plate. The heating process was applied for a simple insert model with dimensions of 50 mm × 50 mm × 2 mm, in order to verify the influence of the FFD geometry on the heating result. After that, Ex-GMTC with the assistance of FFD was carried out for a mold-reading process, and the FFD influence was estimated by the mold heating result and the improvement of the melt flow length using acrylonitrile butadiene styrene (ABS). The results show that the air sprue gap (h) significantly affects the temperature of the insert and an air sprue gap of 3 mm gives the best heating rate, with the highest temperature being 321.2 °C. Likewise, the actual results show that the height of the flow focusing device (V) also influences the temperature of the insert plate and that a 5 mm high FFD gives the best results with a maximum temperature of 332.3 °C. Moreover, the heating efficiency when using FFD is always higher than without FFD. After examining the effect of FFD, its application was considered, in order to improve the melt flow length in injection molding, which increased from 38.6 to 170 mm, while the balance of the melt filling was also clearly improved.

scholarly journals The Feasibility of an Internal Gas-Assisted Heating Method for Improving the Melt Filling Ability of Polyamide 6 Thermoplastic Composites in a Thin Wall Injection Molding Process

Polymers ◽  
2021 ◽  
Vol 13 (7) ◽  
pp. 1004 ◽  
Author(s):  
Thanh Trung Do ◽  
Tran Minh The Uyen ◽  
Pham Son Minh
Keyword(s):  
Injection Molding ◽  
Heating Rate ◽  
Temperature Control ◽  
Cavity Surface ◽  
Heating Process ◽  
Injection Molding Process ◽  
Thin Wall ◽  
Molding Process ◽  
Filling Ability ◽  
Wall Injection

In thin wall injection molding, the filling of plastic material into the cavity will be restricted by the frozen layer due to the quick cooling of the hot melt when it contacts with the lower temperature surface of the cavity. This problem is heightened in composite material, which has a higher viscosity than pure plastic. In this paper, to reduce the frozen layer as well as improve the filling ability of polyamide 6 reinforced with 30 wt.% glass fiber (PA6/GF30%) in the thin wall injection molding process, a preheating step with the internal gas heating method was applied to heat the cavity surface to a high temperature, and then, the filling step was commenced. In this study, the filling ability of PA6/GF30% was studied with a melt flow thickness varying from 0.1 to 0.5 mm. To improve the filling ability, the mold temperature control technique was applied. In this study, an internal gas-assisted mold temperature control (In-GMTC) using different levels of mold insert thickness and gas temperatures to achieve rapid mold surface temperature control was established. The heating process was observed using an infrared camera and estimated by the temperature distribution and the heating rate. Then, the In-GMTC was employed to produce a thin product by an injection molding process with the In-GMTC system. The simulation results show that with agas temperature of 300 °C, the cavity surface could be heated under a heating rate that varied from 23.5 to 24.5 °C/s in the first 2 s. Then, the heating rate decreased. After the heating process was completed, the cavity temperature was varied from 83.8 to about 164.5 °C. In-GMTC was also used for the injection molding process with a part thickness that varied from 0.1 to 0.5 mm. The results show that with In-GMTC, the filling ability of composite material clearly increased from 2.8 to 18.6 mm with a flow thickness of 0.1 mm.

Dynamic Mold Temperature Control Using Gas-Assisted Heating and Its Effect on the Molding Replication Qualities of Micro Channels

2008 ◽  
Author(s):  
Shia-Chung Chen ◽  
Yaw-Jen Chang ◽  
Jen-An Chang ◽  
Hsin-Shu Peng ◽  
Ying-Chieh Wang
Keyword(s):  
Injection Molding ◽  
Surface Temperature ◽  
Temperature Control ◽  
Heating System ◽  
Mold Temperature ◽  
Mold Surface ◽  
Water Heating ◽  
Molded Part ◽  
Micro Channels ◽  
Gas Heating

Dynamic mold surface temperature control (DMTC) has the advantage of improving molded part qualities without significant increases in cycle time. A gas-assisted heating system combined with water cooling was developed to achieve DMTC for injection molding. With gas-assisted heating, it takes 2s for the mold surface temperature to vary from 60 °C to 120 °C whereas it requires 186s using water heating. Further, it takes 21s and 84s for the mold surface to cool to 60 °C under gas heating and water heating, respectively. The gas-assisted heating system also shows excellent efficiency for micro injection molding of biochips to achieve high replication accuracy of the micro channels.

Sign in / Sign up

Export Citation Format

Share Document