scholarly journals Study on External Gas-Assisted Mold Temperature Control with the Assistance of a Flow Focusing Device in the Injection Molding Process

Materials ◽  
2021 ◽  
Vol 14 (4) ◽  
pp. 965 ◽  
Author(s):  
Nguyen Truong Giang ◽  
Pham Son Minh ◽  
Tran Anh Son ◽  
Tran Minh The Uyen ◽  
Thanh-Hai Nguyen ◽  
...  
Keyword(s):  
Injection Molding ◽  
Temperature Control ◽  
Mold Temperature ◽  
Injection Molding Process ◽  
Melt Flow ◽  
Flow Focusing ◽  
Molding Process ◽  
Heating Efficiency ◽  
Flow Length ◽  
Insert Plate

In the injection molding field, the flow of plastic material is one of the most important issues, especially regarding the ability of melted plastic to fill the thin walls of products. To improve the melt flow length, a high mold temperature was applied with pre-heating of the cavity surface. In this paper, we present our research on the injection molding process with pre-heating by external gas-assisted mold temperature control. After this, we observed an improvement in the melt flow length into thin-walled products due to the high mold temperature during the filling step. In addition, to develop the heating efficiency, a flow focusing device (FFD) was applied and verified. The simulations and experiments were carried out within an air temperature of 400 °C and heating time of 20 s to investigate a flow focusing device to assist with external gas-assisted mold temperature control (Ex-GMTC), with the application of various FFD types for the temperature distribution of the insert plate. The heating process was applied for a simple insert model with dimensions of 50 mm × 50 mm × 2 mm, in order to verify the influence of the FFD geometry on the heating result. After that, Ex-GMTC with the assistance of FFD was carried out for a mold-reading process, and the FFD influence was estimated by the mold heating result and the improvement of the melt flow length using acrylonitrile butadiene styrene (ABS). The results show that the air sprue gap (h) significantly affects the temperature of the insert and an air sprue gap of 3 mm gives the best heating rate, with the highest temperature being 321.2 °C. Likewise, the actual results show that the height of the flow focusing device (V) also influences the temperature of the insert plate and that a 5 mm high FFD gives the best results with a maximum temperature of 332.3 °C. Moreover, the heating efficiency when using FFD is always higher than without FFD. After examining the effect of FFD, its application was considered, in order to improve the melt flow length in injection molding, which increased from 38.6 to 170 mm, while the balance of the melt filling was also clearly improved.

scholarly journals Study on External Gas-Assisted Mold Temperature Control for Improving the Melt Flow Length of Thin Rib Products in the Injection Molding Process

2019 ◽  
Vol 2019 ◽  
pp. 1-17 ◽  
Author(s):  
Phan The Nhan ◽  
Thanh Trung Do ◽  
Tran Anh Son ◽  
Pham Son Minh
Keyword(s):  
Injection Molding ◽  
Temperature Control ◽  
High Efficiency ◽  
Mold Temperature ◽  
Injection Molding Process ◽  
Thin Wall ◽  
Mold Surface ◽  
Melt Flow ◽  
Molding Process ◽  
Flow Length

In the injection molding process, mold temperature control is one of the most efficient methods for improving product quality. In this research, an external gas-assisted mold temperature control (Ex-GMTC) with gas temperature variation from 200°C to 400°C was applied to thin wall injection molding at melt thicknesses from 0.2 to 0.6 mm. The melt flow length was evaluated through the application of this system to the mold of a thin rib product. The results show that the heating process achieves high efficiency in the initial 20 s, with a maximum heating rate of 6.4°C/s. In this case, the mold surface reached 158.4°C. By applying Ex-GMTC to a 0.2 mm flow thickness, the flow length increased from 37.85 to 41.32 mm with polypropylene (PP) material and from 14.54 to 15.8 mm with acrylonitrile butadiene styrene (ABS) material. With the thin rib mold and use of Ex-GMTC, the mold temperature varied from 112.0°C to 140.8°C and the thin rib height reached 7.0 mm.

Numerical Study on the Melt Flow Length of the Composite Materials in the Injection Molding Process

2019 ◽  
Vol 971 ◽  
pp. 15-20
Author(s):  
The Nhan Phan ◽  
Trung Do Thanh ◽  
Son Minh Pham
Keyword(s):  
Composite Materials ◽  
Injection Molding ◽  
Numerical Study ◽  
Mold Temperature ◽  
Injection Molding Process ◽  
Melt Flow ◽  
Molding Process ◽  
Flow Length ◽  
Part Thickness ◽  
Good Agreement

Improving the melt flow length by increasing the mold temperature has been an issue encountered in the injection molding processes for composite products. In this study, an injection molding process was applied to a melt flow length model having a part thickness of 1.0 mm. The mold temperature varied from 30 °C to 110 °C. Six types of composite materials of polycaprolactam 6 (PA6) and glass fiber (GF) were selected to study the influence of mold temperature on the material filling in the injection molding process. The simulation results denoted that the mold temperature considerably influenced the flowability during the injection molding process, especially using 30% GF; further, the melt flow length was increased by 25.5% when the mold temperature was increased from 30 °C to 110 °C. In accordance with the simulation, our experiments demonstrated that we could achieve a mold temperature of 110 °C using all types of composite materials. Therefore, in this study, we denoted that both the simulation and experimental results of the melt flow length were comparable, thereby indicating a good agreement.

scholarly journals Prediction of the maximum flow length of a thin injection molded part

2020 ◽  
Vol 40 (9) ◽  
pp. 783-795
Author(s):  
Sara Liparoti ◽  
Vito Speranza ◽  
Annarita De Meo ◽  
Felice De Santis ◽  
Roberto Pantani
Keyword(s):  
Injection Molding ◽  
Maximum Flow ◽  
Mold Temperature ◽  
Complete Characterization ◽  
Rheological Parameters ◽  
Injection Molding Process ◽  
Spiral Flow ◽  
Molding Process ◽  
Molded Part ◽  
Flow Length

AbstractOne of the most significant issues, when thin parts have to be obtained by injection molding (i.e. in micro-injection molding), is the determination of the conditions of pressure, mold temperature, and injection temperature to adopt to completely fill the cavity. Obviously, modern computational methods allow the simulation of the injection molding process for any material and any cavity geometry. However, this simulation requires a complete characterization of the material for what concerns the rheological and thermal parameters, and also a suitable criterion for solidification. These parameters are not always easily reachable. A simple test aimed at obtaining the required parameters is then highly advantageous. The so-called spiral flow test, consisting of measuring the length reached by a polymer in a long cavity under different molding conditions, is a method of this kind. In this work, with reference to an isotactic polypropylene, some spiral flow tests obtained with different mold temperatures and injection pressures are analyzed with a twofold goal: on one side, to obtain from a few simple tests the basic rheological parameters of the material; on the other side, to suggest a method for a quick prediction of the final flow length.

scholarly journals Improving the Melt Flow Length of Acrylonitrile Butadiene Styrene in Thin-Wall Injection Molding by External Induction Heating with the Assistance of a Rotation Device

Polymers ◽  
2021 ◽  
Vol 13 (14) ◽  
pp. 2288
Author(s):  
Pham Son Minh ◽  
Minh-Tai Le
Keyword(s):  
Injection Molding ◽  
Induction Heating ◽  
Cycle Time ◽  
Heating Surface ◽  
Heating Process ◽  
Injection Molding Process ◽  
Thin Wall ◽  
Melt Flow ◽  
Molding Process ◽  
Flow Length

In injection molding, the temperature control of the dynamic mold is an excellent method for improving the melt flow length, especially of thin-wall products. In this study, the heating efficiency of a novel heating strategy based on induction heating was estimated. With the use of this heating strategy, a molding cycle time similar to the traditional injection molding process could be maintained. In addition, this strategy makes it easier to carry out the heating step due to the separation of the heating position and the mold structure as well as allowing the ease of magnetic control. The results show that, with an initial mold temperature of 30 °C and a gap (G) between the heating surface and the inductor coil of 5 mm, the magnetic heating process can heat the plate to 290 °C within 5 s. However, with a gap of 15 mm, it took up to 8 s to reach 270 °C. According to the measurement results, when the mold heating time during the molding process increased from 0 to 5 s, the flow length increased significantly from 71.5 to 168.1 mm, and the filling percentage of the thin-wall product also increased from 10.2% to 100%. In general, the application of external induction heating (Ex-IH) during the molding cycle resulted in improved melt flow length with minimal increase in the total cycle time, which remained similar to that of the traditional case.

Estimation of Maximum Flow Length for CF-PEEK Overmolded Grid Structures Using the Finite Element Method

2021 ◽  
Author(s):  
Carlos Rodríguez-Mondéjar ◽  
Álvaro Rodríguez-Prieto ◽  
Ana María Camacho
Keyword(s):  
Aspect Ratio ◽  
Injection Molding ◽  
Cross Section ◽  
Maximum Flow ◽  
Thermoplastic Composites ◽  
Injection Molding Process ◽  
Geometrical Parameters ◽  
Molding Process ◽  
Support Tool ◽  
Flow Length

Abstract Injection overmolding process is a high versatile process that permits, when used in combination with fiber reinforced thermoplastic composites, the obtaining of high mechanical properties structures with complex geometries in short time cycles. The maximum flow length is a parameter that reflects the success of filling in a polymer injection molding process. Geometry of the part, rheological properties of the polymer and process parameters, such as injection pressure and temperature, are involved on the value of this parameter and therefore on the viability of a certain configuration. For injection molding manufacturing, the understanding of the relation between maximum flow length and main geometrical parameters of the molded part is fundamental to approach the product design, which is conditioned severely by processing capabilities. In this work, the maximum flow length is obtained for different geometries of an overmolded rectangular stiffener grid of carbon fiber filled polyether eter ketone (CF-PEEK) using the software Moldflow© Adviser© for calculations. Value of maximum flow length is provided as a function of cross section aspect ratio for gate diameters between 0.8 mm and 1.4 mm and cross section areas from 10 to 50 mm2. An exponential decrement of maximum flow length has been observed with the increment of aspect ratio of the cross section as well as a linear increment with the increment of cross section area. Gate diameter variation is slightly related with maximum flow length for the simulated values. These results provide a support tool for geometry sizing in overmolded rectangular grid parts at preliminary design stages.

Optimization of Injection Molding Process Parameters with Material Properties Based on GA and BP

2013 ◽  
Vol 345 ◽  
pp. 586-590 ◽  
Author(s):  
Xiao Hong Tan ◽  
Lei Gang Wang ◽  
Wen Shen Wang
Keyword(s):  
Injection Molding ◽  
Process Parameters ◽  
Mold Temperature ◽  
Injection Molding Process ◽  
Axial Deformation ◽  
Molding Process ◽  
Melt Temperature ◽  
Bp Network ◽  
Injection Parameters ◽  
Moldflow Simulation

To obtain optimal injection process parameters, GA was used to optimize BP network structure based on Moldflow simulation results. The BP network was set up which considering the relationship between volume shrinkage of plastic parts and injection parameters, such as mold temperature, melt temperature, holding pressure and holding time etc. And the optimal process parameters are obtained, which is agreed with actual results. Using BP network to predict injection parameters impact on parts quality can effectively reduce the difficulty and workload of other modeling methods. This method can be extended to other quality prediction in the process of plastic parts.Keyword: Genetic algorithm (GA);Neural network algorithm (BP);Injection molding process optimization;The axial deformation

The simulation of the warpage rule of the thin-walled part of polypropylene composite based on the coupling effect of mold deformation and injection molding process

2018 ◽  
Vol 25 (3) ◽  
pp. 593-601 ◽  
Author(s):  
Jixiang Zhang ◽  
Xiaoyi Yin ◽  
Fengzhi Liu ◽  
Pan Yang
Keyword(s):  
Injection Molding ◽  
Coupling Effect ◽  
Mold Temperature ◽  
Injection Molding Process ◽  
Plastic Part ◽  
Molding Process ◽  
Melt Temperature ◽  
Packing Pressure ◽  
Thin Walled ◽  
Packing Time

Abstract Aiming at the problem that a thin-walled plastic part easily produces warpage, an orthogonal experimental method was used for multiparameter coupling analysis, with mold structure parameters and injection molding process parameters considered synthetically. The plastic part deformation under different experiment schemes was comparatively studied, and the key factors affecting the plastic part warpage were analyzed. Then the injection molding process was optimized. The results showed that the important order of the influence factors for the plastic part warpage was packing pressure, packing time, cooling plan, mold temperature, and melt temperature. Among them, packing pressure was the most significant factor. The optimal injection molding process schemes reducing the plastic part warpage were melt temperature (260°C), mold temperature (60°C), packing pressure (150 MPa), packing time (2 s), and cooling plan 3. In this situation, the forming plate flatness was better.

Sign in / Sign up

Export Citation Format

Share Document