Single-phase-to-ground fault section location in flexible resonant grounding distribution networks using soft open points

2020 ◽  
Vol 122 ◽  
pp. 106198
Author(s):  
Zhengtian Li ◽  
Yuqing Ye ◽  
Xiao Ma ◽  
Xiangning Lin ◽  
Feng Xu ◽  
...  
Keyword(s):  
Single Phase ◽  
Distribution Networks ◽  
Ground Fault

Research on Single-Phase Grounding Fault in Distribution Networks with a DC Power Positioning Method

2014 ◽  
Vol 530-531 ◽  
pp. 353-356
Author(s):  
Run Sheng Li
Keyword(s):  
Power Distribution ◽  
Single Phase ◽  
Distribution Network ◽  
Distribution Networks ◽  
Power Distribution Network ◽  
Power Outage ◽  
Location Method ◽  
Fault Resistance ◽  
Ground Fault ◽  
Positioning Method

Due to the high ground fault resistance and the complexity of power distribution network structure (such as too many nodes, branches and too long lines), adopting common traveling wave method and ac injection method can not effectively locate the single-phase grounding fault in the distribution network system.To solve above problems and determine the position of the point of failure prisely, this paper adopted the dc location method of injecting the dc signal from the point of failure under the power outage offline. This paper introduces the single phase dc method and the method of three phase dc, and the simulation shows that the dc location method is effective and feasible.

scholarly journals Reflected Traveling Wave Based Single-Ended Fault Location in Distribution Networks

Energies ◽  
2020 ◽  
Vol 13 (15) ◽  
pp. 3917 ◽  
Author(s):  
Yangang Shi ◽  
Tao Zheng ◽  
Chang Yang
Keyword(s):  
Traveling Wave ◽  
Power Distribution ◽  
Fault Location ◽  
Single Phase ◽  
Distribution Network ◽  
Distribution Networks ◽  
Power Distribution Networks ◽  
Reflected Waves ◽  
Ground Fault ◽  
Location Methods

Traveling wave (TW)-based fault-location methods have been used to determine single-phase-to-ground fault distance in power-distribution networks. The previous approaches detected the arrival time of the initial traveling wave via single ended or multi-terminal measurements. Regarding the multi-branch effect, this paper utilized the reflected waves to obtain multiple arriving times through single ended measurement. Potential fault sections were estimated by searching for the possible traveling wave propagation paths in accordance with the structure of the distribution network. This approach used the entire propagation of a traveling wave measured at a single end without any prerequisite of synchronization, which is a must in multi-terminal measurements. The uniqueness of the fault section was guaranteed by several independent single-ended measurements. Traveling waves obtained in a real 10 kV distribution network were used to determine the fault section, and the results demonstrate the significant effectiveness of the proposed method.

scholarly journals Mathematical Modeling of Arc Faults in Networks with Low Single Phase-to-Ground Fault Currents

2019 ◽  
Vol 140 ◽  
pp. 05001
Author(s):  
Andrei Brilinskii ◽  
Georgiy Evdokunin ◽  
Anna Petrova ◽  
Irina Ryndina
Keyword(s):  
High Frequency ◽  
Gas Flow ◽  
Single Phase ◽  
Channel Model ◽  
Distribution Networks ◽  
Electric Arc ◽  
Fault Current ◽  
Zero Crossing ◽  
Ground Fault ◽  
Frequency Current

The article comprises the results of the research defining open-flame arcs self-quenching conditions in the event of a single phase-to-ground fault in overhead medium-voltage distribution networks according to existing theories of arc extinguishing. The calculations included metallic and arc faults modeling in a network with low phase-to-ground fault current. The arc gap simulation based on the mathematical channel model of a cylindrically symmetrical upright arc stabilized by rising convective gas flow was carried out in ATPDraw software program. The single phase-to-ground arc fault calculations results indicated an increase in high-frequency currents’ attenuation rate during transient processes as well as a reduce reduction in the electric arc lifetime from 8 ms to 2 ms in case of the breakdown voltage decrease from the peak value to zero. Notably, in case of low single phase-to-ground fault current the arc extinguishing took place at the first high-frequency current zero. For the cases of nonzero breakdown voltages, the electric arc extinguishing was detected at the fundamental frequency current component zero-crossing instant. The maximum overvoltage ratio of K = 2.8 was obtained as athe result of the single phase-to-ground fault at the peak phase voltage.

Sign in / Sign up

Export Citation Format

Share Document