Influence of reflected waves at the bonded boundary in double-layered thickness-shear resonator using α-quartz

The influence of the reflected waves at the bonding boundary on the resonance waveform and temperature characteristics was investigated using α-quartz (QZ). The double-layered resonator specimen was fabricated using 129.55°Y- and 0°Y-cut QZ substrates with the thickness ratio x=0.520. The temperature characteristic at the range from 100°C to 300°C was deviated from the calculated values estimated by the equations considering thickness and electric flux density ratio proposed in the previous work, and the resonant waveform of the specimen was deteriorated as compared with that of single-layer resonators. In order to clarify these phenomena, the phase matching conditions and total amplitude in the specimen were examined. As a result, it was clarified that increase of the amplitude in the layer with lower acoustic impedance was affected to the temperature characteristic, and acoustic losses due to reflection / transmission at the bonding boundary was affected to the total amplitude of resonance.

Study on the efficiency of a transducer for sonochemistry by calorimetry

Sonochemistry is an effective method for initiation or enhancement of the chemical reactions by ultrasound in a wide range of applications. In this study, the efficiency of a sonochemistry transducer, defined as the ratio of ultrasonic power to electrical power, was investigated for different materials and the thicknesses of the vibration plate in the frequency range 22 kHz–2 MHz. The ultrasonic power was measured by calorimetry. To eliminate the influence of reflected waves, the transducer was attached to the side of a cylindrical vessel. The transducer with a stainless-steel vibration plate was more efficient than those with vibration plates of acrylonitrile butadiene styrene plastic or chloroprene rubber. The efficiencies of the transducers also increased with decreasing thickness of the vibration plates. Langevin-type transducers were less efficient than the disk-type transducers.

Зондирование водогазонасыщенных насыпных сред переотраженными волнами непосредственно после воздействия ударной волны

The possibility of using re-reflected waves for sounding bulk water-gas-saturated media after exposure to a shock wave has been investigated. Results are shown using probing pulses.

Use of Attributes on 3D Seismic Data for Studying Mishrif Formation in East Abu-Amoud Field, South-Eastern Iraq

The seismic method depends on the nature of the reflected waves from the interfaces between layers, which in turn depends on the density and velocity of the layer, and this is called acoustic impedance. The seismic sections of the East Abu-Amoud field that is located in Missan Province, south-eastern Iraq, were studied and interpreted for updating the structural picture of the major Mishrif Formation for the reservoir in the field. The Mishrif Formation is rich in petroleum in this area, with an area covering about 820 km2. The horizon was calibrated and defined on the seismic section with well logs data (well tops, check shot, sonic logs, and density logs) in the interpretation process to identify the upper and lower boundaries of the Formation. Seismic attributes were used to study the formation, including instantaneous phase attributes and relative acoustic impedance on time slice of 3D seismic data . Also, relative acoustic impedance was utilized to study the top of the Mishrif Formation. Based on these seismic attributes, karst features of the formation were identified. In addition, the nature of the lithology in the study area and the change in porosity were determined through the relative acoustic impedance The overlap of the top of the Mishrif Formation with the bottom of the Khasib Formation was determined because the Mishrif Formation is considered as an unconformity surface.

Experimental capabilities of seismic emission tomography for solving the problems of searching and exploration of deep hydrocarbon accumulations

The standard seismic prospecting has been designed to investigate thin layering at shallow depths. At depths more than 4 km the rocks are significantly compacted, change their properties and it is often impossible to trace clear horizons by reflected waves. In the crystalline basement and lower horizons of the sedimentary cover the block structure of rocks is clearly manifested. Taking this into account geological models should be developed and other predictive indicators should be used when searching for hydrocarbon accumulations. For the study of great depths more informative seismic methods are emission and transmission tomography which have been developed in detail in seismology. This article discusses prognostic indicators different from seismic prospecting and presents experimental results confirming the success of emission tomography in their detection using the example of field studies at developed hydrocarbon deposit and other geophysical objects. The range of working depths of research covers the entire crust of the Earth including the crust-mantle transition zone. Keywords: seismic emission; emission tomography; rocks; hydrocarbon deposits.

Study on Low-Frequency Abnormal Signal and Structural Characteristics of 2015 Azuoqi Ms5.8 Earthquake

In this article, the phenomenon of low-frequency abnormal signals before earthquakes, which reflects the three elements of earthquakes and the beneath structure change information, is discussed. Based on the data recorded at the Shizuishan (SZS), Wuhai (WUH) and Dongshenmiao seismic stations around the epicenter of the Ms5.8 earthquake in Azuoqi, Inner Mongolia, in 2015, the low-frequency abnormal signal from the seismic waves before this earthquake is extracted. At the same time, the autocorrelation method is used to extract the reflected waves of the main interface from teleseismic events recorded by the seismic array in the epicenter area, and then the change information from the beneath structure is obtained. It is explained in time and space that the low-frequency abnormal signal before the main earthquake, extracted from the continuous waveform, is directly related to the change in the underground structure near the epicenter, and it can be determined that the wave propagation direction f the crustal stress before the earthquake is from south to north, and it continues to accumulate near the epicenter until the main earthquake occurs.

Edge and Notch Detection in a Plate Using Time Reversal Process of Leaky Lamb Waves

Leaky Lamb waves are proven effective to carry out nondestructive testing especially on parallel and immersed plates. To detect and localize defects in such a set, this work associates for the first time the topological energy method and leaky Lamb waves. This methodology is applied in a single immersed plate to validate its application. Firstly, Lamb mode A1 is generated in the plate, and the reflected waves on the defect are measured. A first case is examined where the edge is considered as a defect to be localized. Then, measurements are taken on a plate where a notch is machined. The measurements are time reversed and reinjected in a finite-element simulation. The results are then correlated with the direct problem of the topological energy method that is also simulated. In both cases, the defects are precisely localized on the energy images. This work is the preliminary step to an application of the topological energy method to a set of two parallel and immersed plates where the research defect is located in the second plate.

Numerical Investigation on Guided Waves Dispersion and Scattering Phenomena in Stiffened Panels

The aim of this work is to propose a numerical methodology based on the finite element (FE) method to investigate the dispersive behavior of guided waves transmitted, converted, and reflected by reinforced aluminum and composite structures, highlighting their differences. The dispersion curves of such modes can help designers in improving the damage detection sensitivity of Lamb wave based structural health monitoring (SHM) systems. A preliminary phase has been carried out to assess the reliability of the modelling technique. The accuracy of the results has been demonstrated for aluminum and composite flat panels by comparing them against experimental tests and semi-analytical data, respectively. Since the good agreement, the FE method has been used to analyze the phenomena of dispersion, scattering, and mode conversion in aluminum and composite panels characterized by a structural discontinuity, as a stiffener. The research activity allowed emphasizing modes conversion at the stiffener, offering new observations with respect to state of the art. Converted modes propagate with a slightly slower speed than the incident ones. Reflected waves, instead, have been found to travel with the same velocity of the incident ones. Moreover, waves reflected in the composite stiffened plate appeared different from those that occurred in the aluminum one for the aspects herein discussed.

Influence of Diffusion and Impedence Parameters on Wave Propagation in Thermoelastic Medium

The aim of the present paper is to study the impact of diffusion and impedance parameters on the propagation of plane waves in a thermoelastic medium for Green and Lindsay theory (G-L) and the Coupled theory (C-T) of thermoelasticity. Results are demonstrated for impedance boundary conditions and the amplitude ratios of various reflected waves against the angle of incidence are calculated numerically. The characteristics of diffusion, relaxation time and impedence parameter on amplitude ratios have been depicted graphically. Some cases of interest are also derived from the present investigation.

Least-Squares Reverse Time Migration Using the Gradient Preconditioning Based on Transmitted Wave Energy

A gradient preconditioning approach based on transmitted wave energy for least-squares reverse time migration (LSRTM) is proposed in this study. The gradient is preconditioned by using the energy of “approximate transmission wavefield,” which is calculated based on the non-reflecting acoustic equation. The proposed method can effectively avoid a huge amount of calculation and storage required by the Hessian matrix or approximated Hessian matrix and can overcome the influence of reflected waves, multiples, and other wavefields on the gradient in gradient preconditioning based on seismic wave energy (GPSWE). The numerical experiments, compared with that using GPSWE, show that LSRTM using the gradient preconditioning based on transmitted wave energy (GPTWE) can significantly improve the imaging accuracy of deep target and accelerate the convergence rate without trivial increased calculation.