scholarly journals Influence of different air inflow rates on low-pressure flash evaporation from a water pool

2022 ◽  
Vol 171 ◽  
pp. 107234
Author(s):  
Peiwei Ni ◽  
Zhi Wen ◽  
Fuyong Su
Keyword(s):  
Low Pressure ◽  
Water Pool ◽  
Flash Evaporation

scholarly journals Exploration of Impinging Water Spray Heat Transfer at System Pressures Near the Triple Point

2013 ◽  
Author(s):  
Eric L. Golliher ◽  
Shi-chune Yao
Keyword(s):  
Heat Transfer ◽  
Triple Point ◽  
Low Pressure ◽  
Transfer Model ◽  
Space Vehicles ◽  
Water Spray ◽  
Flash Evaporation ◽  
Multiphase Transport ◽  
Triple Point Of Water ◽  
Ice Water

The heat transfer of a water spray impinging upon a surface in a very low pressure environment is of interest to cooling of space vehicles during launch and re-entry, and to industrial processes where flash evaporation occurs. At very low pressure, the process occurs near the triple point of water, and there exists a transient multiphase transport problem of ice, water and water vapor. At the impingement location, there are three heat transfer mechanisms: evaporation, freezing and sublimation. A preliminary heat transfer model was developed to explore the interaction of these mechanisms at the surface and within the spray.

Enhanced tunneled surfaces for water pool boiling heat transfer under low pressure

2018 ◽  
Vol 116 ◽  
pp. 93-103 ◽  
Author(s):  
Tomasz Halon ◽  
Bartosz Zajaczkowski ◽  
Sandra Michaie ◽  
Romuald Rulliere ◽  
Jocelyn Bonjour
Keyword(s):  
Heat Transfer ◽  
Boiling Heat Transfer ◽  
Pool Boiling ◽  
Low Pressure ◽  
Water Pool ◽  
Pool Boiling Heat Transfer

Effects of Electrical Discharges in Low Pressure Gases on the Morphology of Polyethylene Crystals

1974 ◽  
Vol 32 ◽  
pp. 544-545
Author(s):  
L.H. Bolz ◽  
D.H. Reneker
Keyword(s):  
Power Distribution ◽  
Electrical Discharge ◽  
Dielectric Breakdown ◽  
Ionic Species ◽  
Low Pressure ◽  
Polymer Surfaces ◽  
Electrical Discharges ◽  
Adhesive Bonds ◽  
Power Distribution Lines ◽  
Modification Of The Surface

The attack, on the surface of a polymer, by the atomic, molecular and ionic species that are created in a low pressure electrical discharge in a gas is interesting because: 1) significant interior morphological features may be revealed, 2) dielectric breakdown of polymeric insulation on high voltage power distribution lines involves the attack on the polymer of such species created in a corona discharge, 3) adhesive bonds formed between polymer surfaces subjected to such SDecies are much stronger than bonds between untreated surfaces, 4) the chemical modification of the surface creates a reactive surface to which a thin layer of another polymer may be bonded by glow discharge polymerization.

Structure of Palladium Single-Crystal Films Prepared by Flash Evaporation onto (001) NaCl Substrates

1970 ◽  
Vol 28 ◽  
pp. 456-457
Author(s):  
L. E. Murr ◽  
G. Wong
Keyword(s):  
Single Crystal ◽  
High Vacuum ◽  
Ultra High Vacuum ◽  
High Rate ◽  
Flash Evaporation ◽  
Optimum Load ◽  
Single Crystal Films ◽  
Crystal Films ◽  
A Current

Palladium single-crystal films have been prepared by Matthews in ultra-high vacuum by evaporation onto (001) NaCl substrates cleaved in-situ, and maintained at ∼ 350° C. Murr has also produced large-grained and single-crystal Pd films by high-rate evaporation onto (001) NaCl air-cleaved substrates at 350°C. In the present work, very large (∼ 3cm2), continuous single-crystal films of Pd have been prepared by flash evaporation onto air-cleaved (001) NaCl substrates at temperatures at or below 250°C. Evaporation rates estimated to be ≧ 2000 Å/sec, were obtained by effectively short-circuiting 1 mil tungsten evaporation boats in a self-regulating system which maintained an optimum load current of approximately 90 amperes; corresponding to a current density through the boat of ∼ 4 × 104 amperes/cm2.

Field ion microscopy

1988 ◽  
Vol 46 ◽  
pp. 434-435
Author(s):  
Gert Ehrlich
Keyword(s):  
Low Temperature ◽  
Sample Surface ◽  
Low Pressure ◽  
Radius Of Curvature ◽  
Field Ion Microscopy ◽  
Phosphor Screen ◽  
Ion Microscopy ◽  
Field Ion Microscope

The field ion microscope, devised by Erwin Muller in the 1950's, was the first instrument to depict the structure of surfaces in atomic detail. An FIM image of a (111) plane of tungsten (Fig.l) is typical of what can be done by this microscope: for this small plane, every atom, at a separation of 4.48Å from its neighbors in the plane, is revealed. The image of the plane is highly enlarged, as it is projected on a phosphor screen with a radius of curvature more than a million times that of the sample. Müller achieved the resolution necessary to reveal individual atoms by imaging with ions, accommodated to the object at a low temperature. The ions are created at the sample surface by ionization of an inert image gas (usually helium), present at a low pressure (< 1 mTorr). at fields on the order of 4V/Å.

Formation of high temperature phase in flash-evaporated SnSe films

1990 ◽  
Vol 48 (4) ◽  
pp. 698-699
Author(s):  
J.P.S. Hanjra
Keyword(s):  
Thin Films ◽  
Electrical Properties ◽  
Energy Gap ◽  
Dominant Role ◽  
Fine Powder ◽  
High Temperature Phase ◽  
Temperature Phase ◽  
Water Mixture ◽  
Flash Evaporation ◽  
Photovoltaic Applications

Tin mono selenide (SnSe) with an energy gap of about 1 eV is a potential material for photovoltaic applications. Various authors have studied the structure, electronic and photoelectronic properties of thin films of SnSe grown by various deposition techniques. However, for practical photovoltaic junctions the electrical properties of SnSe films need improvement. We have carried out investigations into the properties of flash evaporated SnSe films. In this paper we report our results on the structure, which plays a dominant role on the electrical properties of thin films by TEM, SEM, and electron diffraction (ED).Thin films of SnSe were deposited by flash evaporation of SnSe fine powder prepared from high purity Sn and Se, onto glass, mica and KCl substrates in a vacuum of 2Ø micro Torr. A 15% HF + 2Ø% HNO3 solution was used to detach SnSe film from the glass and mica substrates whereas the film deposited on KCl substrate was floated over an ethanol water mixture by dissolution of KCl. The floating films were picked up on the grids for their EM analysis.

Sign in / Sign up

Export Citation Format

Share Document