Heat transfer and friction factor correlations for slip gaseous fluid flow in confined porous medium with pore-scale LBM modelling

2022 ◽  
Vol 173 ◽  
pp. 107382
Author(s):  
Ammar Tariq ◽  
Zhenyu Liu
Keyword(s):  
Heat Transfer ◽  
Porous Medium ◽  
Fluid Flow ◽  
Friction Factor ◽  
Pore Scale

scholarly journals Numerical Simulation of Williamson Combined Natural and Forced Convective Fluid Flow between Parallel Vertical Walls with Slip Effects and Radiative Heat Transfer in a Porous Medium

Entropy ◽  
2016 ◽  
Vol 18 (4) ◽  
pp. 147 ◽  
Author(s):  
Mohammad Abdollahzadeh Jamalabadi ◽  
Payam Hooshmand ◽  
Navid Bagheri ◽  
HamidReza KhakRah ◽  
Majid Dousti
Keyword(s):  
Heat Transfer ◽  
Numerical Simulation ◽  
Porous Medium ◽  
Fluid Flow ◽  
Radiative Heat Transfer ◽  
Radiative Heat ◽  
Slip Effects ◽  
Vertical Walls ◽  
Convective Fluid

Compact Modeling of Fluid Flow and Heat Transfer in Straight Fin Heat Sinks

2004 ◽  
Vol 126 (2) ◽  
pp. 247-255 ◽  
Author(s):  
Duckjong Kim ◽  
Sung Jin Kim
Keyword(s):  
Heat Transfer ◽  
Porous Medium ◽  
Fluid Flow ◽  
Pressure Drop ◽  
Heat Sink ◽  
Volume Averaging ◽  
Thermal Design ◽  
Heat Sinks ◽  
Compact Modeling ◽  
Flow And Heat Transfer

In the present work, a compact modeling method based on a volume-averaging technique is presented. Its application to an analysis of fluid flow and heat transfer in straight fin heat sinks is then analyzed. In this study, the straight fin heat sink is modeled as a porous medium through which fluid flows. The volume-averaged momentum and energy equations for developing flow in these heat sinks are obtained using the local volume-averaging method. The permeability and the interstitial heat transfer coefficient required to solve these equations are determined analytically from forced convective flow between infinite parallel plates. To validate the compact model proposed in this paper, three aluminum straight fin heat sinks having a base size of 101.43mm×101.43mm are tested with an inlet velocity ranging from 0.5 m/s to 2 m/s. In the experimental investigation, the heat sink is heated uniformly at the bottom. The resulting pressure drop across the heat sink and the temperature distribution at its bottom are then measured and are compared with those obtained through the porous medium approach. Upon comparison, the porous medium approach is shown to accurately predict the pressure drop and heat transfer characteristics of straight fin heat sinks. In addition, evidence indicates that the entrance effect should be considered in the thermal design of heat sinks when Re Dh/L>∼O10.

Scaling group analysis of bioconvective micropolar fluid flow and heat transfer in a porous medium

2020 ◽  
Author(s):  
Kohilavani Naganthran ◽  
Md Faisal Md Basir ◽  
Thirupathi Thumma ◽  
Ebenezer Olubunmi Ige ◽  
Roslinda Nazar ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Porous Medium ◽  
Fluid Flow ◽  
Micropolar Fluid ◽  
Group Analysis ◽  
Flow And Heat Transfer ◽  
Micropolar Fluid Flow ◽  
Scaling Group

Experimental and Numerical Studies of Fluid Flow Confined in Microchannel

2016 ◽  
Author(s):  
Yan Wang ◽  
Xiang Ling
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Reynolds Number ◽  
Fluid Flow ◽  
Friction Factor ◽  
Heat Transfer Performance ◽  
Pure Water ◽  
High Heat Flux ◽  
Transfer Performance ◽  
Parallel Microchannels

The heat transfer performance of fluid flowing in a microchannel was experimentally studied, to meet the requirement of extremely high heat flux removal of microelectronic devices. There were 10 parallel microchannels with rectangular cross-section in the stainless steel plate, which was covered by a glass plate to observe the fluid flowing behavior, and another heating plate made of aluminum alloy was positioned behind the microchannel. Single phase heat transfer and fluid flow downstream the microchannel experiments were conducted with both deionized water and ethanol. Besides experiments, numerical models were also set up to make a comparison with experimental results. It is found that the pressure drop increases rapidly with enlarging Reynolds number (200), especially for ethanol. With comparison, the flow resistance of pure water is smaller than ethanol. Results also show that the friction factor decreases with Reynolds number smaller than the critical value, while increases the velocity, the friction factor would like to keep little changed. We also find that the water friction factors obtained by CFD simulations in parallel microchannels are much larger than experiment results. With heat flux added to the fluid, the heat transfer performance can be enhanced with larger Re number and the temperature rise could be weaken. Compared against ethanol, water performed much better for heat removal. However, with intensive heat flux, both water and ethanol couldn’t meet the requirement and the temperature at outlet would increase remarkably, extremely for ethanol. These findings would be helpful for thermal management design and optimization.

Thermal Optimization of Microchannel Heat Sink With Pin Fin Structures

2003 ◽  
Author(s):  
Duckjong Kim ◽  
Sung Jin Kim
Keyword(s):  
Heat Transfer ◽  
Porous Medium ◽  
Fluid Flow ◽  
Heat Sink ◽  
Volume Averaging ◽  
Heat Sinks ◽  
Pumping Power ◽  
Heat Transfer Characteristics ◽  
Pin Fin ◽  
Flow And Heat Transfer

In the present work, a novel compact modeling method based on the volume-averaging technique and its application to the analysis of fluid flow and heat transfer in pin fin heat sinks are presented. The pin fin heat sink is modeled as a porous medium. The volume-averaged momentum and energy equations for fluid flow and heat transfer in pin fin heat sinks are obtained using the local volume-averaging method. The permeability, the Ergun constant and the interstitial heat transfer coefficient required to solve these equations are determined experimentally. To validate the compact model proposed in this paper, 20 aluminum pin fin heat sinks having a 101.43 mm × 101.43 mm base size are tested with an inlet velocity ranging from 1 m/s to 5 m/s. In the experimental investigation, the heat sink is heated uniformly at the bottom. Pressure drop and heat transfer characteristics of pin fin heat sinks obtained from the porous medium approach are compared with experimental results. Upon comparison, the porous medium approach is shown to predict accurately the pressure drop and heat transfer characteristics of pin fin heat sinks. Finally, surface porosities of the pin fin heat sink for which the thermal resistance of the heat sink is minimal are obtained under constraints on pumping power and heat sink size. The optimized pin fin heat sinks are shown to be superior to the optimized straight fin heat sinks in thermal performance by about 50% under the same constraints on pumping power and heat sink size.

Sign in / Sign up

Export Citation Format

Share Document