Response to thermal exposure of the mechanically alloyed Al/C powder blends

2008 ◽  
Vol 460 (1-2) ◽  
pp. L1-L5 ◽  
Author(s):  
Yücel Birol
Keyword(s):  
Thermal Exposure ◽  
Mechanically Alloyed ◽  
Powder Blends

Investigation of Mechanochemical Synthesized Tungsten Silicides from WO3, SiO2 and Mg Blends

2016 ◽  
Vol 257 ◽  
pp. 47-51 ◽  
Author(s):  
Didem Ovalı ◽  
M. Lütfi Öveçoğlu
Keyword(s):  
Reaction Times ◽  
Thermodynamic Calculations ◽  
Initial Powder ◽  
Mechanically Alloyed ◽  
Tungsten Silicide ◽  
Excess Amount ◽  
Powder Blends ◽  
Final Composition ◽  
Tungsten Silicides

In this study, tungsten silicide powders mechanochemically synthesized using WO3-SiO2-Mg powder blends. Stoichiometric proportions and excess amounts of initial powders were used to indicate the effects of final composition of synthesized tungsten silicide powders. Since the initial powder compositions affect the reaction times, all compositions were mechanically alloyed for 1 hour. In addition, thermodynamic calculations of all compositions were theoretically conducted. The dominant phases are WSi2 and MgO for all mechanically alloyed powders. Results show that the excess amount additions of initial powders directly effects the amount and formation of resultant phases in the synthesized powder compositions.

Fine Microstructure of a Mechanically Alloyed Oxide Dispersion Strengthened Nickel-Base Superalloy

1977 ◽  
Vol 35 ◽  
pp. 298-299
Author(s):  
Jordi Marti ◽  
Timothy E. Howson ◽  
David Kratz ◽  
John K. Tien
Keyword(s):  
Solid Solution ◽  
Volume Fraction ◽  
Stress Rupture ◽  
Oxide Dispersion Strengthened ◽  
Solid Solution Alloy ◽  
Oxide Dispersion ◽  
Creep And Stress Rupture ◽  
Mechanically Alloyed ◽  
Fine Microstructure ◽  
Nickel Base

The previous paper briefly described the fine microstructure of a mechanically alloyed oxide dispersion strengthened nickel-base solid solution. This note examines the fine microstructure of another mechanically alloyed system. This alloy differs from the one described previously in that it is more generously endowed with coherent precipitate γ forming elements A1 and Ti and it contains a higher volume fraction of the finely dispersed Y2O3 oxide. An interesting question to answer in the comparative study of the creep and stress rupture of these two ODS systems is the role of the precipitate γ' in the mechanisms of creep and stress rupture in alloys already containing oxide dispersoids.The nominal chemical composition of this alloy is Ni - 20%Cr - 2.5%Ti - 1.5% A1 - 1.3%Y203 by weight. The system receives a three stage heat treatment-- the first designed to produce a coarse grain structure similar to the solid solution alloy but with a smaller grain aspect ratio of about ten.

Microstructure of mechanically alloyed and hot-pressed Al5CuZr2

1990 ◽  
Vol 48 (4) ◽  
pp. 970-971
Author(s):  
T. E. Mitchell ◽  
P. B. Desch ◽  
R. B. Schwarz
Keyword(s):  
Mechanical Alloying ◽  
Vickers Hardness ◽  
Hot Pressing ◽  
Rapid Quenching ◽  
Hardened Steel ◽  
Alloyed Powder ◽  
Ion Milling ◽  
Mechanical Grinding ◽  
Mechanically Alloyed ◽  
Steel Container

Al3Zr has the highest melting temperature (1580°C) among the tri-aluminide intermetal1ics. When prepared by casting, Al3Zr forms in the tetragonal DO23 structure but by rapid quenching or by mechanical alloying (MA) it can also be prepared in the metastable cubic L12 structure. The L12 structure can be stabilized to at least 1300°C by the addition of copper and other elements. We report a TEM study of the microstructure of bulk Al5CuZr2 prepared by hot pressing mechanically alloyed powder.MA was performed in a Spex 800 mixer using a hardened steel container and balls and adding hexane as a surfactant. Between 1.4 and 2.4 wt.% of the hexane decomposed during MA and was incorporated into the alloy. The mechanically alloyed powders were degassed in vacuum at 900°C. They were compacted in a ram press at 900°C into fully dense samples having Vickers hardness of 1025. TEM specimens were prepared by mechanical grinding followed by ion milling at 120 K. TEM was performed on a Philips CM30 at 300kV.

Innovative electrotechnological systems to provide the temperature modes of technological pipelines

2019 ◽  
Vol 2 (1) ◽  
pp. 29-39 ◽  
Author(s):  
S. G. Konesev ◽  
P. A. Khlyupin
Keyword(s):  
Induction Heating ◽  
Thermal Exposure ◽  
Heating System ◽  
The Arctic ◽  
Process Conditions ◽  
Heating Systems ◽  
Fluid Properties ◽  
Low Efficiency ◽  
Extreme North ◽  
Induction Heating System

Introduction: the systems of thermal effects on thermo-dependent, viscous and highly viscous liquids under conditions of the Arctic and the Extreme North are considered. Low efficiency and danger of heating systems based on burned hydrocarbons, heated liquids and steam are shown. Electrothermal heating systems used to maintain thermo-dependent fluids in a fluid state are considered. The evaluation of the effectiveness of the application of the most common electrothermal system — heating cables (tapes). The most effective electrothermal system based on induction technologies has been determined. Materials and methods: considered methods of thermal exposure to maintain the fluid properties of thermo-dependent fluids at low extreme temperatures. Results: presents an induction heating system and options for its implementation in the Extreme North and the Arctic. Conclusions: induction heating system to minimize loss of product quality, improve the system performance under changing process conditions, eliminate fire product, to reduce the influence of the human factor.

Sign in / Sign up

Export Citation Format

Share Document