Effects of sintering temperature on the mechanical properties of sintered NdFeB permanent magnets prepared by spark plasma sintering

2014 ◽  
Vol 349 ◽  
pp. 1-4 ◽  
Author(s):  
G.P. Wang ◽  
W.Q. Liu ◽  
Y.L. Huang ◽  
S.C. Ma ◽  
Z.C. Zhong
Keyword(s):  
Mechanical Properties ◽  
Spark Plasma Sintering ◽  
Permanent Magnets ◽  
Sintering Temperature ◽  
Plasma Sintering ◽  
Spark Plasma

Microstructure and Mechanical Properties of Spark-Plasma-Sintered SiC-TiC Composites

2005 ◽  
Vol 287 ◽  
pp. 335-339 ◽  
Author(s):  
Kyeong Sik Cho ◽  
Kwang Soon Lee
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Heating Rate ◽  
Spark Plasma Sintering ◽  
Sintering Temperature ◽  
Applied Pressure ◽  
Argon Atmosphere ◽  
Full Density ◽  
Plasma Sintering ◽  
Spark Plasma

Rapid densification of the SiC-10, 20, 30, 40wt% TiC powder with Al, B and C additives was carried out by spark plasma sintering (SPS). In the present SPS process, the heating rate and applied pressure were kept at 100°C/min and at 40 MPa, while the sintering temperature varied from 1600-1800°C in an argon atmosphere. The full density of SiC-TiC composites was achieved at a temperature above 1800°C by spark plasma sintering. The 3C phase of SiC in the composites was transformed to 6H and 4H by increasing the process temperature and the TiC content. By tailoring the microstructure of the spark-plasma-sintered SiC-TiC composites, their toughness could be maintained without a notable reduction in strength. The strength of 720 MPa and the fracture toughness of 6.3 MPa·m1/2 were obtained in the SiC-40wt% TiC composite prepared at 1800°C for 20 min.

Fabrication of MgO/Graphene Composites by Combustion Synthesis and Spark Plasma Sintering

2018 ◽  
Vol 281 ◽  
pp. 125-130
Author(s):  
Nan Lu ◽  
Jia Xi Liu ◽  
Gang He ◽  
Jiang Tao Li
Keyword(s):  
Mechanical Properties ◽  
Combustion Synthesis ◽  
Spark Plasma Sintering ◽  
Sintering Temperature ◽  
Ceramic Composites ◽  
Combustion Reaction ◽  
Sintering Additive ◽  
Microstructure And Mechanical Properties ◽  
Plasma Sintering ◽  
Spark Plasma

MgO/Graphene ceramic composites were fabricated by combining combustion synthesis with spark plasma sintering. MgO/Graphene mixture powders were prepared by the combustion reaction between Mg powders and CO2 gas. Dense MgO/Graphene composites were fabricated by spark plasma sintering (SPS) using LiF as the sintering additive. The effect of the sintering temperature on microstructure and mechanical properties of the prepared MgO/Graphene ceramics was discussed. The sintering temperature of the MgO/Graphene mixture powders increased from 900°C to 1300°C. The highest density of 3.43g/cm3 and hardness of 2133MPa were obtained at 1100°C. Compared with monolithic MgO ceramics, the hardness of MgO/Graphene ceramics at the same sintering temperature was increased from 840MPa to 2133MPa.

Fabrication of TiAl Intermetallic by Spark Plasma Sintering

2007 ◽  
Vol 336-338 ◽  
pp. 1050-1052 ◽  
Author(s):  
Hai Tao Wu ◽  
Yun Long Yue ◽  
Wei Bing Wu ◽  
Hai Yan Yin
Keyword(s):  
Mechanical Properties ◽  
Intermetallic Compounds ◽  
Spark Plasma Sintering ◽  
Bending Strength ◽  
Sintering Temperature ◽  
Three Point Bending ◽  
The Poor ◽  
High Relative Density ◽  
Plasma Sintering ◽  
Spark Plasma

The γ-TiAl intermetallic compounds were produced at the temperature ranging from 850°C to 1050°C by the Spark Plasma Sintering (SPS) process. The effects of sintering temperature and holding time on the mechanical properties of γ-TiAl intermetallic compounds were investigated. The γ-TiAl intermetallic compounds sintered at 1050°C for 10 min showed a high relative density more than 98%, and had the best three-point bending strength of 643MPa, fracture toughness of 12 MPa·m1/2 and microhardness of 560MPa. The microstructural observations indicated typical characteristics of intergranular fracture, which meant the poor ductility of γ-TiAl intermetallic compounds.

Microstructure and Properties of Spark Plasma Sintering AlN/BN Ceramics

2006 ◽  
Vol 313 ◽  
pp. 105-108 ◽  
Author(s):  
Lian Meng Zhang ◽  
Mei Juan Li ◽  
Qiang Shen ◽  
T. Li ◽  
M.Q. Yu
Keyword(s):  
Mechanical Properties ◽  
Thermal Conductivity ◽  
Mechanical Strength ◽  
Spark Plasma Sintering ◽  
Volume Fraction ◽  
Sintering Temperature ◽  
Composite Ceramics ◽  
Plasma Sintering ◽  
Spark Plasma ◽  
Full Densification

Aluminum nitride-boron nitride (AlN/BN) composite ceramics were prepared by spark plasma sintering (SPS). The sintering behaviors of AlN/BN composites with 5~15% volume fraction of BN were studied. The influences of BN content, as well as the sintering temperature on the density, microstructure, mechanical strength, thermal conductivity and machinability of the composites were also investigated. The results showed that the full densification of AlN/BN composite ceramics could be realized by SPS technique at the temperature no higher than 1800°C for 3 minutes. The thermal conductivity of AlN/BN composites is in the range of 66~79W/mK, and AlN/BN composites can be cut or drilled by carbides or even steel tools when BN content is 15% volume fraction. The mechanical strength of AlN/BN composites is about 330MPa and is not remarkably affected by the addition of BN. The improvement of mechanical properties of AlN/BN composite ceramics is due to the fine and homogenous microstructure developed in the SPS process.

Microstructure and Mechanical Properties of ZrO2(Y2O3)-Al2O3 Nano Composites Prepared by Spark Plasma Sintering

2008 ◽  
Author(s):  
Shufeng Li ◽  
Hiroshi Izui ◽  
Michiharu Okano ◽  
Weihua Zhang ◽  
Taku Watanabe
Keyword(s):  
Mechanical Properties ◽  
Spark Plasma Sintering ◽  
Sintering Temperature ◽  
Alumina Ceramic ◽  
The Other ◽  
Sintering Behavior ◽  
Nanocomposite Powder ◽  
Mixed Powder ◽  
Plasma Sintering ◽  
Spark Plasma

Zirconia (Y2O3)-alumina ceramic nanocomposites were fabricated by spark plasma sintering (SPS). A commercially available nanocomposite powder TZP-3Y20A was used as starting powder, the other from conventionally mechanical mixed powder 3YSZ-20A used for comparison. The effect of sintering temperature on the densification, sintering behavior, mechanical properties, and microstructure of the composites were investigated. The results show that the density increase with increasing of sintering temperature, and thus mechanical properties were strengthened with enhancing of densification. The nanocomposite powder TZP-3Y20A was easily sintered and good mechanical properties were achieved, compared with the powder from conventionally mechanical mixed, where the maximum strength and toughness of composites are 967 MPa and 5.27 MPam1/2, respectively.

Mechanical properties of spark plasma sintering Nd-Fe-B permanent magnets

2007 ◽  
Vol 204 (12) ◽  
pp. 4149-4152 ◽  
Author(s):  
Ming Yue ◽  
Aili Cao ◽  
Gongping Wang ◽  
Weiqiang Liu ◽  
Jiuxing Zhang
Keyword(s):  
Mechanical Properties ◽  
Spark Plasma Sintering ◽  
Permanent Magnets ◽  
Plasma Sintering ◽  
Spark Plasma
Sign in / Sign up

Export Citation Format

Share Document