Optimisation of scale-up of microbial fuel cell for sustainable wastewater treatment with positive net energy generation

Simultaneous organics removal and nitrification using a novel nitrifying biocathode microbial fuel cell (MFC) reactor were investigated in this study. Remarkably, the introduction of nitrifying biomass into the cathode chamber caused higher voltage outputs than that of MFC operated with the abiotic cathode. Results showed the maximum power density increased 18% when cathode was run under the biotic condition and fed by nitrifying medium with alkalinity/NH4+-N ratio of 8 (26 against 22 mW/m2). The voltage output was not differentiated when NH4+-N concentration was increased from 50 to 100 mg/L under such alkalinity/NH4+-N ratio. However, interestingly, the cell voltage rose significantly when the alkalinity/NH4+-N ratio was decreased to 6. Consequently, the maximum power density increased 68% in compared with the abiotic cathode MFC (37 against 22 mW/m2). Polarization curves demonstrated that both activation and concentration losses were lowered during the period of nitrifying biocathode operation. Ammonium was totally nitrified and mostly converted to nitrate in all cases of the biotic cathode conditions. High COD removal efficiency (98%) was achieved. In light of the results presented here, the application of nitrifying biocathode is not only able to integrate the nitrogen and carbon removal but also to enhance the power generation in MFC system. Our system can be suggested to open up a new feasible way for upgrading and retrofitting the existing wastewater treatment plant by the use of MFC-based technologies.

Download Full-text

Scale up of Microbial Fuel Cell Stack System for Residential Wastewater Treatment in Continuous Mode Operation

Water ◽

10.3390/w11020217 ◽

2019 ◽

Vol 11 (2) ◽

pp. 217 ◽

Cited By ~ 9

Author(s):

Rodrigo Valladares Linares ◽

Jorge Domínguez-Maldonado ◽

Ernesto Rodríguez-Leal ◽

Gabriel Patrón ◽

Alfonso Castillo-Hernández ◽

...

Keyword(s):

Wastewater Treatment ◽

Fuel Cell ◽

Microbial Fuel Cell ◽

Scale Up ◽

Oxygen Demand ◽

Domestic Wastewater ◽

Septic Tank ◽

Efficient Technology ◽

Fuel Cell Stack ◽

Treated Effluent

The most important operational expense during wastewater treatment is electricity for pumping and aeration. Therefore, this work evaluated operational parameters and contaminant removal efficiency of a microbial fuel cell stack system (MFCSS) that uses no electricity. This system consists of (i) septic tank primary treatment, (ii) chamber for secondary treatment containing 18 MFCs, coupled to an energy-harvesting circuit (EHC) that stores the electrons produced by anaerobic respiration, and (iii) gravity-driven disinfection (sodium hypochlorite 5%). The MFCSS operated during 60 days (after stabilization period) and it was gravity-fed with real domestic wastewater from a house (5 inhabitants). The flow rate was 600 ± 100 L∙d−1. The chemical oxygen demand, biological oxygen demand, total nitrogen and total phosphorous were measured in effluent, with values of 100 ± 10; 12 ± 2; 9.6 ± 0.5 and 4 ± 0.2 mg∙L−1, and removal values of 86%, 87%, 84% and 64%, respectively. Likewise, an EHC (ultra-low energy consumption) was built with 6.3 V UCC® 4700 µF capacitors that harvested and stored energy from MFCs in parallel. Energy management was programmed on a microcontroller Atmega 328PB®. The water quality of the treated effluent complied with the maximum levels set by the Mexican Official Standard NOM-001-SEMARNAT-1996-C. A cost analysis showed that MFCSS could be competitive as a sustainable and energy-efficient technology for real domestic wastewater treatment.

Download Full-text