scholarly journals Post-liquefaction deformation and strength characteristics of sand in torsional shear tests

2021 ◽  
Author(s):  
Muhammad Umar ◽  
Takashi Kiyota ◽  
Gabriele Chiaro ◽  
Antoine Duttine
Keyword(s):  
Strength Characteristics ◽  
Shear Tests ◽  
Torsional Shear ◽  
Deformation And Strength Characteristics

Study of operating properties of aanticorrosion packing papers

2020 ◽  
Vol 76 (10) ◽  
pp. 1021-1027
Author(s):  
A. P. Ponomarev ◽  
L. G. Kolyada ◽  
E. V. Tarasyuk
Keyword(s):  
Steel Strip ◽  
Low Carbon Steel ◽  
Strength Characteristics ◽  
Low Carbon ◽  
Operating Characteristics ◽  
Packing Materials ◽  
Accelerated Corrosion ◽  
Operating Properties ◽  
Deformation And Strength Characteristics ◽  
Anticorrosion Properties

Metal products are subjected to atmospheric corrosion during transportation and storing. An important way to prevent this negative phenomenon is application of special packing materials, in particular materials, containing volatile inhibitors of corrosion, which protect metal against various corrosion agents. To protect metal effectively it is necessary to provide a definite level of operating characteristics of packing materials. The purpose of the work was the study of operating properties of inhibited crepe, inhibited and laminated polyethylene film, inhibited crepe and reinforced by polypropylene web papers, manufactured by OJSC “PP TechnoKhim”, Magnitogorsk, used for packing of metals. Structural and dimensional, sorption, deformation and strength characteristics, of the studied anticorrosion papers are presented, the characteristics being calculated based on the results of measurements. To determine their physical-mechanical and anticorrosion properties, standard methods and methodologies were used. To evaluate impact of moisture and transportation conditions, indices of water adsorption and wear of the studied papers were determined. Inhibitor content in these materials was determined by thermogravimetric analysis method. Their protective ability was studied on samples of low carbon steel strip. For accelerated corrosion tests the strip samples were degreased by alcohol, dried in air and packed in the studied anticorrosion papers, after that they were exposed under increased temperatures and moisture conditions. It was determined, that among the materials under the study, the inhibited crepe paper, reinforced by polypropylene web, hhas the best complex of physical-mechanical and anticorrosion properties. It provides a higher level of prevention corrosion of metal l and surpasses other materials in a number of deformation and strength characteristics. Recommendations were proposed to improve qquality of produced anticorrosion papers.

scholarly journals The Shear Strength Characteristics of Frozen Coarse Granular Debris

1984 ◽  
Vol 30 (106) ◽  
pp. 348-357 ◽  
Author(s):  
W.G. Nickling ◽  
L. Bennett
Keyword(s):  
Shear Strength ◽  
Normal Load ◽  
Strength Characteristics ◽  
Shear Tests ◽  
Critical Limit ◽  
Load Rate ◽  
Polycrystalline Ice ◽  
Saturated Sample ◽  
The Difference ◽  
Ice Content

AbstractThe effect of ice content and normal load on the shear strength characteristics of a frozen coarse granular debris was investigated. 31 shear tests were carried out in a modified shearbox allowing a sample temperature of (–1.0 ± 0.2)° C and a load rate of 9.63 × 10−4 cm/min. The tests showed that as the ice content of the frozen debris was increased from 0% (under-saturated) to 25% (saturated), sample shear strength was markedly increased. In contrast, sample shear strength was reduced as ice content was increased from 25% (saturated) to 100% (supersaturated). The changes in shear strength with increasing ice content were attributed directly to changes in internal friction and the cohesive effects of the pore ice. The shear tests also indicate that shear strength increases with increasing normal load up to a critical limit. Above this limit, dilatancy is suppressed causing the shear strength to decrease or remain relatively constant with increased normal load.The stress-strain curves of the 31 tests indicated that samples with higher ice contents tended to reach peak strength (τP) with less displacement during shear. Moreover, the difference between τp and τr (residual strength) was lowest for pure polycrystalline ice and highest for ice-saturated samples. The Mohr-Coulomb failure envelopes displayed very distinctive parabolic curvilinearity. The degree of curvature is thought to be a function of ice creep at low normal loads and particle fracture and crushing at high normal loads.

Deformation and strength characteristics of magnesia-spinnellide refractories at elevated temperatures

Refractories ◽  
1991 ◽  
Vol 32 (7-8) ◽  
pp. 403-406
Author(s):  
R. A. Panfilov ◽  
V. M. Ustyantsev ◽  
T. I. Remezova ◽  
S. P. Postnikova ◽  
M. Ya. Landa ◽  
...  
Keyword(s):  
Elevated Temperatures ◽  
Strength Characteristics ◽  
Deformation And Strength Characteristics

The Shear Strength Characteristics of Frozen Coarse Granular Debris

1984 ◽  
Vol 30 (106) ◽  
pp. 348-357 ◽  
Author(s):  
W.G. Nickling ◽  
L. Bennett
Keyword(s):  
Shear Strength ◽  
Normal Load ◽  
Strength Characteristics ◽  
Shear Tests ◽  
Critical Limit ◽  
Load Rate ◽  
Polycrystalline Ice ◽  
Saturated Sample ◽  
The Difference ◽  
Ice Content

Abstract The effect of ice content and normal load on the shear strength characteristics of a frozen coarse granular debris was investigated. 31 shear tests were carried out in a modified shearbox allowing a sample temperature of (–1.0 ± 0.2)° C and a load rate of 9.63 × 10−4 cm/min. The tests showed that as the ice content of the frozen debris was increased from 0% (under-saturated) to 25% (saturated), sample shear strength was markedly increased. In contrast, sample shear strength was reduced as ice content was increased from 25% (saturated) to 100% (supersaturated). The changes in shear strength with increasing ice content were attributed directly to changes in internal friction and the cohesive effects of the pore ice. The shear tests also indicate that shear strength increases with increasing normal load up to a critical limit. Above this limit, dilatancy is suppressed causing the shear strength to decrease or remain relatively constant with increased normal load. The stress-strain curves of the 31 tests indicated that samples with higher ice contents tended to reach peak strength (τP) with less displacement during shear. Moreover, the difference between τp and τr (residual strength) was lowest for pure polycrystalline ice and highest for ice-saturated samples. The Mohr-Coulomb failure envelopes displayed very distinctive parabolic curvilinearity. The degree of curvature is thought to be a function of ice creep at low normal loads and particle fracture and crushing at high normal loads.

scholarly journals Deformation and strength characteristics of Laves phases in titanium alloys

2019 ◽  
Vol 179 ◽  
pp. 107891 ◽  
Author(s):  
C.D. Rabadia ◽  
Y.J. Liu ◽  
L.Y. Chen ◽  
S.F. Jawed ◽  
L.Q. Wang ◽  
...  
Keyword(s):  
Titanium Alloys ◽  
Strength Characteristics ◽  
Laves Phases ◽  
Deformation And Strength Characteristics
Sign in / Sign up

Export Citation Format

Share Document