scholarly journals Integrated studies to identify site-specific parameters for environmentally benign mining operations: A case study from the Sukari Gold Mine, Egypt

2021 ◽  
Vol 750 ◽  
pp. 141654
Author(s):  
Ahmed Abdelaal ◽  
Mohamed Sultan ◽  
Mohamed Elhebiry ◽  
R.V. Krishnamurthy ◽  
Neil Sturchio
2021 ◽  
Author(s):  
Christopher Powell ◽  
Nathan Brockhurst ◽  
Jean Christoph Wemmers ◽  
Marisa Torombe ◽  
Eamon Eames ◽  
...  
Keyword(s):  

2020 ◽  
Vol 1 (1) ◽  
pp. 6-12
Author(s):  
Bella Puspa Octaviania ◽  
Supriyadi ◽  
Ambran Hartono

A lack of method to find out the fairness limit of fuel consumption in mining operations enables statistical approach with two-tail test be applied to observe the fairness limit of actual fuel oil consumption compared to the manual handbook of its equipment. Fuel consumption according to the manual handbook for EXCA LIEBHERR 9350 excavator is 207.23 liters/hour and EXCA HITACHI 2500 is 191.51 liters/hour, while CATERPILLAR 777D Dump Truck is 36-53 liters/hour consider as low, 53-73, 8 liters/hour medium, and 73.8-96.5 liters/hour as high. This statistical approach has been carried out after fulfilling the concept of mechanized earth-moving. As a result, the differences in fuel consumption of LIEBHERR 9350 and HITACHI 2500 are 3.72% and 3.26%, which are still in range of a reasonable fuel consumption limit, while CAT 777D operating on LIEBHERR 9350 and CAT 777D operating on HITACHI 2500, each shows a difference in fuel consumption. The differences are 29.65%, meaning that it has exceeded the reasonable limits of fuel consumption and 7.15%, meaning that it is still in range of a reasonable fuel consumption limit.


Water ◽  
2022 ◽  
Vol 14 (2) ◽  
pp. 165
Author(s):  
Alexander I. Malov ◽  
Evgeniya S. Sidkina ◽  
Mikhail V. Mironenko ◽  
Alexey S. Tyshov ◽  
Elena V. Cherkasova

The technogenic impact of the development of the Lomonosov diamond deposit is associated with the discharge of quarry and drainage water into the river, which has a special conservation status. Earlier studies on the composition of bottom sediments showed that there are signs of increased accumulation of heavy metals and radionuclides at wastewater discharge sites. The purpose of this work was to predict changes in the composition of surface water and bottom sediment in the river during the further development of mining operations with brackish and salty water captured by drainage systems, the presence of which was established in the zone of their future influence. For this, a simulation of changes in the composition of the water in the river was carried out using the GEOCHEQ software package by minimizing the free energy of the system using a convex simplex algorithm. It was found that the maximum salinity of surface water can reach 1.51 g/L. In this case, the MPC of Cl−, Na+, SO42−, Mg2+, Sr, V, and U can be exceeded for fishery watercourses. The genetic basis of the accumulation of these components in solutions for mixing was considered. According to the calculations, when about 5000 m3/h of drainage water is discharge d into the river, the mass of precipitated chemical elements will be 56–191 t/h, including up to 2.1 t/h of iron; therefore, accumulation in the discharge zone must be controlled.


2009 ◽  
Vol 9 (2) ◽  
pp. 127-132 ◽  
Author(s):  
Gertjan Medema ◽  
Patrick Smeets

System assessment is the part of the Water Safety Plan that evaluates whether a water supply system is capable of producing drinking water that meets the health-based targets. System assessment can be done at increasing level of detail, requiring more site specific information as the level of detail increases. Four case studies are presented with increasing level of detail, showing the type of information that is required for each of these levels and how each level informs risk management. The first case study shows how a system assessment can be performed without other site specific information than the type of source water and the type of treatment processes. The required data for the system assessment are collected from the large body of literature available. The second case study uses site specific microbial indicator data. The third study uses pathogen data and the fourth case study combines data on pathogens, microbial indicators and process parameters. The case studies show that the level of detail required largely depends on the risk management question.


Sign in / Sign up

Export Citation Format

Share Document