Modified Galileo self-refrigerated liquefaction process for economical heavy hydrocarbon removal during gas liquefaction

2021 ◽  
Vol 47 ◽  
pp. 101539
Author(s):  
Mahsa Yousefikhanghah ◽  
Laleh Shirazi ◽  
Abbas Naderifar ◽  
Mehran Sarmad
2020 ◽  
Vol 4 (1) ◽  
pp. 1-44
Author(s):  
An Wang ◽  
◽  
Dongyi Fang ◽  

This paper focus on the characteristics of heavy hydrocarbon frozen stoppage, which is based on the investigation of current problems of liquefied natural gas factory. Combined with the causes of frozen study, the paper analyzes the four kinds of technological schemes, such as "adsorption", "heavy hydrocarbon washing", "gas stripping + heavy hydrocarbon backflow" and "low temperature distillation" in a LNG project in Inner Mongolia of CNPC. It analysis the merits and drawbacks of every proposals from process simulation, process description, applicability, temperature parameters, liquefaction energy consumption, major equipment, investment etc. Finally this paper selects a heavy hydrocarbon removal process proposal, which is suitable for a LNG factory in Inner Mongolia, and is more simple process, low energy consumption, easy to operate. After the project is put into operation, the comparison between actual operation data and designed data proves the feasibility of this proposal. The results provide a guidance and reference for the subsequent LNG factory designing


1952 ◽  
Vol 44 (3) ◽  
pp. 447-447
Author(s):  
John Keistler ◽  
Matthew Winkle
Keyword(s):  

Materials ◽  
2021 ◽  
Vol 14 (11) ◽  
pp. 3138
Author(s):  
Kamila Gosz ◽  
Agnieszka Tercjak ◽  
Adam Olszewski ◽  
Józef Haponiuk ◽  
Łukasz Piszczyk

The utilization of forestry waste resources in the production of polyurethane resins is a promising green alternative to the use of unsustainable resources. Liquefaction of wood-based biomass gives polyols with properties depending on the reagents used. In this article, the liquefaction of forestry wastes, including sawdust, in solvents such as glycerol and polyethylene glycol was investigated. The liquefaction process was carried out at temperatures of 120, 150, and 170 °C. The resulting bio-polyols were analyzed for process efficiency, hydroxyl number, water content, viscosity, and structural features using the Fourier transform infrared spectroscopy (FTIR). The optimum liquefaction temperature was 150 °C and the time of 6 h. Comprehensive analysis of polyol properties shows high biomass conversion and hydroxyl number in the range of 238–815 mg KOH/g. This may indicate that bio-polyols may be used as a potential substitute for petrochemical polyols. During polyurethane synthesis, materials with more than 80 wt% of bio-polyol were obtained. The materials were obtained by a one-step method by hot-pressing for 15 min at 100 °C and a pressure of 5 MPa with an NCO:OH ratio of 1:1 and 1.2:1. Dynamical-mechanical analysis (DMA) showed a high modulus of elasticity in the range of 62–839 MPa which depends on the reaction conditions.


Fuel ◽  
2019 ◽  
Vol 257 ◽  
pp. 116026 ◽  
Author(s):  
Quazi Mahzabin Rahman ◽  
Bo Zhang ◽  
Lijun Wang ◽  
Abolghasem Shahbazi

2021 ◽  
Vol 23 (4) ◽  
pp. 1404-1446 ◽  
Author(s):  
Ibrahim Alper Basar ◽  
Huan Liu ◽  
Helene Carrere ◽  
Eric Trably ◽  
Cigdem Eskicioglu

This paper summarizes the existing hydrothermal liquefaction process literature and reveals the effect of process parameters on the bio-crude yield.


2021 ◽  
Vol 243 ◽  
pp. 114363
Author(s):  
Ahmad Naquash ◽  
Muhammad Abdul Qyyum ◽  
Junaid Haider ◽  
Hankwon Lim ◽  
Moonyong Lee

2003 ◽  
pp. 35-45
Author(s):  
Tetsuya TSURUMI ◽  
Hiroshi NAKAZAWA ◽  
Kunio MIZUMOTO ◽  
Hiroyuki WATANABE

Sign in / Sign up

Export Citation Format

Share Document