Vision-based system for simultaneous monitoring of shaft rotational speed and axial vibration using non-projection composite fringe pattern

2019 ◽  
Vol 120 ◽  
pp. 765-776 ◽  
Author(s):  
Jianfeng Zhong ◽  
Shuncong Zhong ◽  
Qiukun Zhang ◽  
Nuno Maia ◽  
Yaochun Shen ◽  
...  
Keyword(s):  
Rotational Speed ◽  
Fringe Pattern ◽  
Axial Vibration

Vision-Based Measurement System for Instantaneous Rotational Speed Monitoring Using Linearly Varying-Density Fringe Pattern

2018 ◽  
Vol 67 (6) ◽  
pp. 1434-1445 ◽  
Author(s):  
Jianfeng Zhong ◽  
Shuncong Zhong ◽  
Qiukun Zhang ◽  
Zhike Peng ◽  
Shulin Liu ◽  
...  
Keyword(s):  
Measurement System ◽  
Rotational Speed ◽  
Fringe Pattern

Measurement of instantaneous rotational speed using double-sine-varying-density fringe pattern

2018 ◽  
Vol 103 ◽  
pp. 117-130 ◽  
Author(s):  
Jianfeng Zhong ◽  
Shuncong Zhong ◽  
Qiukun Zhang ◽  
Zhike Peng
Keyword(s):  
Rotational Speed ◽  
Fringe Pattern

MODULATED FRINGE PATTERN PHOTOBLEACHING APPLIED TO LIPID-WATER CUBIC PHASES : STRUCTURAL INFORMATION

1990 ◽  
Vol 51 (C7) ◽  
pp. C7-105-C7-108
Author(s):  
S. CRIBIER ◽  
L. BOURDIEU ◽  
R. VARGAS ◽  
A. GULIK ◽  
V. LUZZATI
Keyword(s):  
Fringe Pattern ◽  
Structural Information ◽  
Cubic Phases

Straight-Move Robot Control System with LabView-Based Proportional Integral Derivative (PID) Control

2019 ◽  
Vol 3 (2) ◽  
pp. 13-24
Author(s):  
Andrean George W
Keyword(s):  
Pid Control ◽  
Rotational Speed ◽  
Pid Controller ◽  
Dc Motor ◽  
Motor Speed ◽  
Labview Software ◽  
Dc Motors ◽  
Dc Motor Control ◽  
Process System ◽  
Interface Devices

Abstract - Control and monitoring of the rotational speed of a wheel (DC motor) in a process system is very important role in the implementation of the industry. PWM control and monitoring for wheel rotational speed on a pair of DC motors uses computer interface devices where in the industry this is needed to facilitate operators in controlling and monitoring motor speed. In order to obtain the best controller, tuning the Integral Derifative (PID) controller parameter is done. In this tuning we can know the value of proportional gain (Kp), integral time (Ti) and derivative time (Td). The PID controller will give action to the DC motor control based on the error obtained, the desired DC motor rotation value is called the set point. LabVIEW software is used as a PE monitor, motor speed control. Keyword : LabView, Motor DC, Arduino, LabView, PID.

Processing of granite quarry solid waste into industrial high silica materials using leaching process with HCl concentration variation

2020 ◽  
Vol 11 (2) ◽  
pp. 43-50
Author(s):  
Yusup Hendronursito ◽  
Muhammad Amin ◽  
Slamet Sumardi ◽  
Roniyus Marjunus ◽  
Frista Clarasati ◽  
...  
Keyword(s):  
Particle Size ◽  
Rotational Speed ◽  
Inductively Coupled Plasma ◽  
Chemical Elements ◽  
Silica Content ◽  
X Ray ◽  
Concentration Variation ◽  
Leaching Process ◽  
Hcl Concentration ◽  
Granite Powder

This study was aimed to increase granite's silica content using the leaching process with HCl concentration variation. The granite used in this study came from Lematang, South Lampung. This study aims to determine the effect of variations in HCl concentration, particle size, and rotational speed on the crystalline phase and chemical elements formed in the silica product produced from granite. The HCl concentration variations were 6.0 M, 7.2 M, 8.4 M, and 9.6 M, the variation in particle size used was 270 and 400 mesh. Variations in rotational speed during leaching were 500 and 750 rpm. Granite powder was calcined at 1000 ºC for 2 hours. Characterization was performed using X-Ray Fluorescence (XRF), X-Ray Diffraction (XRD), and Inductively Coupled Plasma-Optical Emission Spectroscopy (ICP- OES). The results showed that the silica content increased with increasing HCl concentration, the finer the particle size, and the higher the rotational speed. XRF analysis showed that the silica with the highest purity was leached with 9.6 HCl with a particle size of 400 mesh and a rotational speed of of 750 rpm, which was 73.49%. Based on the results above, by leaching using HCl, the Si content can increase from before. The XRD diffractogram showed that the granite powder formed the Quartz phase.

Sign in / Sign up

Export Citation Format

Share Document