98/02428 Flue gas desulfurization of lignite-fired power stations with limestone or fine lime

1998 ◽  
Vol 39 (3) ◽  
pp. 219
2011 ◽  
Vol 356-360 ◽  
pp. 1516-1519 ◽  
Author(s):  
Jiang Wu ◽  
Jin Hong Zhang ◽  
Wei Feng Xu ◽  
Yu Ran Cai ◽  
Yuan Huang Ouyang ◽  
...  

Along with the rapid development of electric power industry in China, the pollutant discharge limits are getting more strict, and WFGD (wet flue gas desulfurization) technology and its equipment have been greatly developed and extensively applied, in which the gas-gas heater (GGH) is adopted at lots of the power stations. The corrosion is a very important issue in GGH, and it is experimentally studied in this paper. Through experiment of polarization curves and the control variable method, a comparative analysis of the corrosion resistance between the commonly used materials of the GGH is made. The results have shown that the corrosion resistance with the heat transfer surface in GGH will decrease with the temperature increasing, but the enamel steel’s corrosion resistance and stability is strikingly better than that of others, and the increasing volume of corrosion resistance by plating enamel is remarkable.


1998 ◽  
Vol 17 (8) ◽  
pp. 523-533 ◽  
Author(s):  
James C. Hower ◽  
Uschi M. Graham ◽  
Amy S. Wong ◽  
J.David Robertson ◽  
Bethel O. Haeberlin ◽  
...  

2014 ◽  
Vol 30 (6) ◽  
Author(s):  
Lawrence Koech ◽  
Ray Everson ◽  
Hein Neomagus ◽  
Hilary Rutto

AbstractFlue gas desulfurization (FGD) technology has been adopted by a number of power stations for the removal of sulfur dioxide (SO


Minerals ◽  
2021 ◽  
Vol 11 (10) ◽  
pp. 1044
Author(s):  
Katarzyna Jadwiga Stanienda-Pilecki

The purpose of this article was to present the theory of the possibility of using limestone sorbents containing carbonate minerals with increased Mg content in processes of flue gas desulfurization in power stations. Data obtained as a result of the conducted research show that the analyzed Triassic (Muschelkalk) limestones of the south-west part of Poland are built of the following carbonate minerals: low magnesium calcite, high magnesium calcite, dolomite and huntite. These carbonate minerals are characterized by various magnesium contents. The increased content of magnesium in the sorbent has a positive effect on the technological process of flue gas desulfurization using the dry method, especially in the case of desulfurization with the application of Fluidized Bed Reactors. The positive influence of magnesium’s presence in sorbent in the desulfurization process is connected with the decarbonization of carbonate phases with magnesium at temperatures similar to the dolomite decarbonization temperatures, which are, thus, lower than typical for low magnesium calcite. The process would be easier because the structure of a solid solution containing magnesium ions, with a smaller ion radius to calcium ions, is unstable and the decomposition of these phases runs easier and faster. Therefore, the desulfurization process starts earlier and is more effective.


Alloy Digest ◽  
1994 ◽  
Vol 43 (5) ◽  

Abstract URANUS 52N is a nitrogen-alloyed duplex stainless steel improved in stress-corrosion cracking resistance and with pitting and crevice corrosion resistance better than AISI Type 317L. Applications include handling phosphoric acid contaminated with chlorides and in flue gas desulfurization scrubbers. This datasheet provides information on composition, physical properties, and tensile properties. It also includes information on high temperature performance and corrosion resistance as well as forming, heat treating, and joining. Filing Code: SS-566. Producer or source: Creusot-Marrel.


Alloy Digest ◽  
2004 ◽  
Vol 53 (8) ◽  

Abstract AL 4565 alloy has a high level of austenitizers, which provides the microstructure with a high resistance to sigma formation during welding. The high nitrogen also gives the alloy superior strength among the austenitics. Applications include flue gas desulfurization and handling seawater. This datasheet provides information on composition, physical properties, hardness, elasticity, and tensile properties as well as fracture toughness. It also includes information on high temperature performance and corrosion resistance as well as heat treating and joining. Filing Code: SS-906. Producer or source: Allegheny Ludlum Corporation.


Sign in / Sign up

Export Citation Format

Share Document