Effect of void size and Mg contents on plastic deformation behaviors of Al-Mg alloy with pre-existing void: Molecular dynamics study

The plastic deformation properties of cylindrical pre-void Aluminum-Magnesium (Al-Mg) alloy under uniaxial tension are explored using molecular dynamics simulations with embedded atom method (EAM) potential. The factors of Mg content, void size, and temperature are considered. The results show that the void fraction decreases with increasing Mg in the plastic deformation, and it is almost independent of Mg content when Mg is beyond 5%. Both Mg contents and stacking faults around the void affect the void growth. These phenomena are explained by the dislocation density of the sample and stacking faults distribution around the void. The variation trends of yield stress caused by void size are in good agreement with Lubarda model. Moreover, temperature effects are explored, the yield stress and Young's modulus obviously decrease with temperature. Our results may enrich and facilitate the understanding of the plastic mechanism of Al-Mg with defects or other alloys.

Microstructure and mechanical behavior of Al-xMg/5Al2O3 nanostructured composites

The effect of Mg content and milling time were investigated on the microstructure and microhardness values of Al-xMg/5Al2O3 (x = 0, 4, 8 and 12 wt %) nanostructured composite prepared via high energy milling technique. XRD results showed an acceleration of alloying process and formation of Al (Mg) ss by enhancing percentage of Mg element. Also, by increase in Mg percentage the grain size reduction was more considerable during milling treatment. Additionally, increment of the Mg content up to 12 wt%, causes the increase in micro-strain of the samples (from 0.31 to 0.82%). Increase in Mg concentration accelerates the mechanical milling process. According to SEM results a coaxial and circular morphology with a uniform distribution of powder particles has been formed. Up to 12 wt% (for each milling time), significant increase in microhardness (215 HV) was carried out due to solid solution hardening and crystallite refinement. From 10 to 15 h, a slight increase in microhardness up to 218 HV can be observed.

The Conversion of Calcium-Containing Phases and Their Separation with NaCl in Molten Salt Chlorinated Slags at High Temperature

The titanium resources in Panxi reign, China, have a high-impurities content of Ca and Mg, which is usually processed by the molten salt chlorination process. This process allows higher Ca and Mg content in its furnace burdens. However, there is a huge amount of molten salt chlorinated slag produced by this process, consisting of complex compounds and waste NaCl/KCl salts. These slags are always stockpiled without efficient utilization, causing serious environmental pollutions. To recycle the NaCl in the slag back to the molten salt chlorination process, a novel process to deal with those molten salt chlorinated slags with phase conversion at high temperature is presented in this paper. The calcium-containing solid phase was generated when Na2SiO3 was added to the molten salt chlorinated slags at high temperature, while NaCl was kept as a liquid. Thus, liquid NaCl was easily separated from the calcium-containing solid phase, and it could be reused in the molten salt chlorination process. The conversion of calcium-containing phases and their separation of NaCl are the key parts of this work, and they have been systematically studied in this paper; thermodynamic analysis, phase transformation behavior, and calcium removal behavior have all been investigated. The calcium removal rate is 78.69% when the molar ratio of CaCl2:Na2SiO3 is 1:1.5 at 1173 K and N2 atmosphere.

Hierarchical Mg-Birnessite Nanowall Arrays with Enriched (010) Planes for High Performance Aqueous Mg-Ion Batteries

Birnessite MnO2 is a promising cathode material for aqueous Mg-ion batteries due to its layered structure with large interlayer distance. However, the two-dimensional growth mode of birnessite induces nanosheet morphology with preferred growth of inactive (001) planes with sluggish ion transport kinetics. In this work, a high Mg content birnessite with hierarchical nanowall arrays morphology is prepared by in situ electro-conversion using spinel Mn3O4 nanowall arrays. The electro-conversion Mg-birnessite (ECMB) nanowall arrays are assembled by ultrasmall nanosheets with reduced (001) planes but increased active (010) planes, affording enriched open intercalation channels and shortened Mg2+ diffusion length. Consequently, the ECMB cathode exhibits a large specific reversible capacity of about 255.1 mAh/g at a current density of 200 mA/g, and outstanding cycling stability with 73.6% capacity retention after 3000 cycles. Finally, a 2.2 V aqueous full cell is constructed by using ECMB as positive electrode and polyimide as negative electrode, which achieves a high energy density of 65.2 Wh/kg at a power density of 96 W/kg. This work demonstrates effective crystal plane modulation for Mg-birnessite to achieve superior Mg2+ storage in aqueous batteries.

Fabrication of Mg-Doped Sargassum Biochar for Phosphate and Ammonium Recovery

Biochars prepared from macro-algae have a lower C/N ratio compared to lignocellulosic biochar, which is advantageous for direct nutrition. In particular, Sargassum, a marine macro-algae, has a high Mg content; hence, it can be expected to adsorb P and N simultaneously. In this study, Sargassum horneri biochar (SB), pyrolyzed at 400, 500, and 600 °C, was doped with innate Mg through water leaching, and nutrient recovery from the wastewater-mimicking solution was confirmed. The biochar pyrolyzed at 600 °C showed maximum Mg adsorption during water leaching, and the efficiency of K and Na removal was also high, at 92.7% and 91.9%, respectively. The addition of MgCl2 during pyrolysis and high ion exchange did not show distinct advantages for surface modification and nutrient adsorption. X-ray photoelectron spectroscopy analysis confirmed the participation of biochar in the surface adsorption of Mg and PO4 recovery. The PO4 sorption capacity of biochar reached >120 mg·g−1, while the sorption capacity for NH4 was low, at 22.8–28.2 mg·g−1, suggesting that Mg-surface-doped SB presented excellent phosphorus recovery. Hence, upgrading an adsorbent as a wastewater-treatment material and soil ameliorant that recovers nutrients using innate Mg from Sargassum is possible through appropriate surface modification.

Optoelectronic and Birefringence Properties of Weakly Mg Doped ZnO Thin Films Prepared by Spray Pyrolysis

MgxZn1−xO thin films were deposited on glass substrate with x varied between 0.01 and 0.05 by spray pyrolysis at a temperature of 450 °C. The structural investigation showed that all thin films had ZnO wurtzite structure with a preferred (002) orientation. The gap energy was calculated using Tauc’s plot and it decreased over the Mg content by 0.07 eV. The charge carriers’ density dropped by an order of 105 as Mg content increased whereas the resistivity and the mobility increased. SEM observations revealed a significant difference between undoped and doped thin films. A 632.8 nm laser source prism coupler revealed 2 optical modes for every thin film in each Transverse Electric and Transverse Magnetic mode, the birefringence of the Mg doped films was positive. Both ordinary and extraordinary refractive indexes were found to decrease as the Mg content increased. Great intention has been paid to the relation between the refractive, charge carriers density and the optical band gap.

Optoelectronic and Birefringence Properties of Weakly Mg Doped ZnO Thin films Prepared By Spray Pyrolysis.

MgxZn1−xO thin films were deposited on glass substrate with x varied between 0.01 and 0.05 by spray pyrolysis at a temperature of 450 °C. The structural investigation showed that all thin films had ZnO wurtzite structure with a preferred (002) orientation. The gap energy was calculated using Tauc’s plot and it decreased over the Mg content by 0.07 eV. The charge carriers’ density dropped by an order of 105 as Mg content increased whereas the resistivity and the mobility increased. SEM observations revealed a significant difference between undoped and doped thin films. A 632.8 nm laser source prism coupler revealed 2 optical modes for every thin film in each Transverse Electric and Transverse Magnetic mode, the birefringence of the Mg doped films was positive. Both ordinary and extraordinary refractive indexes were found to decrease as the Mg content increased. Great intention has been paid to the relation between the refractive, charge carriers density and the optical band gap.

Comparison of Mechanical and Microstructural Properties of as-Cast Al-Cu-Mg-Ag Alloys: Room Temperature vs. High Temperature

Unfolding the structure–property linkages between the mechanical performance and microstructural characteristics could be an attractive pathway to develop new single- and polycrystalline Al-based alloys to achieve ambitious high strength and fuel economy goals. A lot of polycrystalline as-cast Al-Cu-Mg-Ag alloy systems fabricated by conventional casting techniques have been reported to date. However, no one has reported a comparison of mechanical and microstructural properties that simultaneously incorporates the effects of both alloy chemistry and mechanical testing environments for the as-cast Al-Cu-Mg-Ag alloy systems. This preliminary prospective paper presents the examined experimental results of two alloys (denoted Alloy 1 and Alloy 2), with constant Cu content of ~3 wt.%, Cu/Mg ratios of 12.60 and 6.30, and a constant Ag of 0.65 wt.%, and correlates the synergistic comparison of mechanical properties at room and elevated temperatures. According to experimental results, the effect of the precipitation state and the mechanical properties showed strong dependence on the composition and testing environments for peak-aged, heat-treated specimens. In the room-temperature mechanical testing scenario, the higher Cu/Mg ratio alloy with Mg content of 0.23 wt.% (Alloy 1) possessed higher ultimate tensile strength when compared to the low Cu/Mg ratio with Mg content of 0.47 wt.% (Alloy 2). From phase constitution analysis, it is inferred that the increase in strength for Alloy 1 under room-temperature tensile testing is mainly ascribable to the small grain size and fine and uniform distribution of θ precipitates, which provided a barrier to slip by deaccelerating the dislocation movement in the room-temperature environment. Meanwhile, Alloy 2 showed significantly less degradation of mechanical strength under high-temperature tensile testing. Indeed, in most cases, low Cu/Mg ratios had a strong influence on the copious precipitation of thermally stable omega phase, which is known to be a major strengthening phase at elevated temperatures in the Al-Cu-Mg-Ag alloying system. Consequently, it is rationally suggested that in the high-temperature testing scenario, the improvement in mechanical and/or thermal stability in the case of the Alloy 2 specimen was mainly due to its compositional design.

Calculation Based on the Formation of Mg2Si and Its Effect on the Microstructure and Properties of Al–Si Alloys

In order to investigate the effect of Mg2Si formation on the microstructure and properties of an Al−Si alloy, the critical point of a hypereutectic Al−17Si−4Cu−Mg alloy was calculated by Pandat software. The calculation results of the equilibrium phase diagram show that the critical point for Mg2Si phase formation for the alloy was obtained when the Mg content was 2.2%. The contents of 0.5 wt.% Mg and 2.5 wt.% Mg were selected as the research object. The content of Mg increased from 0.5 wt.% to 2.5 wt.%, the eutectic Si in the matrix was reduced, and the Chinese character-like Mg2Si phase appeared in the microstructure. In the peak ageing state, in addition to θ” and Q’ phases that were mainly precipitated, there was also needle-like β” precipitation in the 2.5 wt.% Mg content alloy. Larger precipitates were found in 2.5 wt.% content alloys, mainly due to the promotion of the solid solution having the aggregation and segregation of more solute elements in the matrix. The tensile strength, elongation, and hardness of hypereutectic Al−17Si−4Cu−0.5Mg alloy under peak ageing were 331 MPa, 3.11%, and 152.1 HB, respectively. The tensile strength and the elongation decreased while the hardness increased with the 2.5 wt.% Mg content, which is due to the formation of hard and brittle Mg2Si and Al8FeMg3Si, which has a splitting effect on the matrix.

Increased Provision of Bioavailable Mg through Vegetables Could Significantly Reduce the Growing Health and Economic Burden Caused by Mg Malnutrition

Magnesium (Mg) is an essential mineral nutrient for human health and its deficiency associated with many diseases, including stroke, heart failure, and type 2 diabetes. Vegetables are an important source of dietary Mg for humans. In this study, we quantified vegetable Mg content by a global meat analysis, analyzed human health, and economic impact caused by Mg deficiency. Results revealed that vegetable Mg content showed a large variation with an average value of 19.3 mg 100 g−1 FW. Variation in per capita vegetable-Mg supply in different continents is largely ascribed to continental difference in the amount and the type of vegetables produced. The health and economic loss attributed to Mg deficiency are estimated to be 1.91 million disability-adjusted life years (DALYs) and 15.8 billion dollars (0.14% of GDP), respectively. A scenario analysis indicated that the increasing vegetable production (increased by 8.9% and 20.7% relative to 2017 in 2030 and 2050) and vegetable Mg content (increased by 22% through biofortification) could significantly reduce DALYs (1.24 million years) and economic burden (0.09% of GDP). This study could guide a major re-balance of production practices, species cultivated, and Mg biofortification to provide sufficient vegetable Mg for better human Mg nutrition.