Mechanical properties of α-cordierite and β-spodumene glass-ceramics prepared by sintering and crystallization heat treatments

1997 ◽  
Vol 23 (5) ◽  
pp. 401-407 ◽  
Author(s):  
Yun-Mo Sung
Keyword(s):  
Mechanical Properties ◽  
Glass Ceramics ◽  
Heat Treatments ◽  
Crystallization Heat

Effect of Heat Treatments on the Mechanical Properties of a Form Tool

2018 ◽  
Vol 10 (3) ◽  
pp. 03032-1-03032-3
Author(s):  
Brahim Chermime ◽  
◽  
Abdelaziz Abboudi ◽  
Hamid Djebaili ◽  
◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Heat Treatments

scholarly journals Effects of equal channel angular pressing and heat treatments on the microstructures and mechanical properties of selective laser melted and cast AlSi10Mg alloys

2021 ◽  
Vol 21 (3) ◽  
Author(s):  
Przemysław Snopiński ◽  
Mariusz Król ◽  
Marek Pagáč ◽  
Jana Petrů ◽  
Jiří Hajnyš ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Low Temperature ◽  
Equal Channel Angular Pressing ◽  
Heat Treatments ◽  
Electron Backscattered Diffraction ◽  
Angular Pressing ◽  
Low Temperature Annealing ◽  
Transmission Electron ◽  
Before And After ◽  
The Impact

AbstractThis study investigated the impact of the equal channel angular pressing (ECAP) combined with heat treatments on the microstructure and mechanical properties of AlSi10Mg alloys fabricated via selective laser melting (SLM) and gravity casting. Special attention was directed towards determining the effect of post-fabrication heat treatments on the microstructural evolution of AlSi10Mg alloy fabricated using two different routes. Three initial alloy conditions were considered prior to ECAP deformation: (1) as-cast in solution treated (T4) condition, (2) SLM in T4 condition, (3) SLM subjected to low-temperature annealing. Light microscopy, transmission electron microscopy, X-ray diffraction line broadening analysis, and electron backscattered diffraction analysis were used to characterize the microstructures before and after ECAP. The results indicated that SLM followed by low-temperature annealing led to superior mechanical properties, relative to the two other conditions. Microscopic analyses revealed that the partial-cellular structure contributed to strong work hardening. This behavior enhanced the material’s strength because of the enhanced accumulation of geometrically necessary dislocations during ECAP deformation.

Crystal Phase Formation and Mechanical Properties of Lithium Disilicate Glass-Ceramics for Dental Restoration

2010 ◽  
Vol 177 ◽  
pp. 447-450 ◽  
Author(s):  
Xin Zhang ◽  
Yi Wen Hu ◽  
Yin Wu ◽  
Wen Jie Si
Keyword(s):  
Mechanical Properties ◽  
Phase Formation ◽  
Glass Ceramics ◽  
High Strength ◽  
Lithium Disilicate ◽  
Sem Analysis ◽  
Dental Restoration ◽  
Bending Test ◽  
Crystal Phase ◽  
High Temperature Xrd

The purpose of this study was to evaluate the crystal phase formation behavior and its influence on the mechanical properties of LiO2-SiO2-P2O5 glass-ceramics system. High temperature XRD was used to analyze the crystal phase formation in situ. The crystalline phases in the material both before and after heat-treatment were also analyzed. The flexural strength was measured by three-point bending test according to ISO 6872:2008(E). The SEM analysis showed that the high strength of the glass-ceramics is attributed to the continuous interlocking microstructure with fine lithium disilicate crystallines.

The influence of heat treatments on the microstructure and the mechanical properties in commercial 7020 alloys

2015 ◽  
Vol 626 ◽  
pp. 254-262 ◽  
Author(s):  
M.C. Paulisch ◽  
N. Wanderka ◽  
M. Haupt ◽  
S. Selve ◽  
I. Driehorst ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Heat Treatments
Sign in / Sign up

Export Citation Format

Share Document