FEM Analysis of Rolling Pressure Along Strip Width in Cold Rolling Process

2007 ◽  
Vol 14 (5) ◽  
pp. 22-26 ◽  
Author(s):  
Xiang-hua Liu ◽  
Xu Shi ◽  
Shan-qing Li ◽  
Jian-yong Xu ◽  
Guo-dong Wang
Keyword(s):  
Cold Rolling ◽  
Fem Analysis ◽  
Rolling Process ◽  
Strip Width ◽  
Rolling Pressure

An Automatic Control Strategy of Strip Width in Cold Rolling

2014 ◽  
Vol 1004-1005 ◽  
pp. 1221-1225
Author(s):  
Ji Lai Yu ◽  
Ting Quan Gu ◽  
Jian Guo Wang
Keyword(s):  
Cold Rolling ◽  
Automatic Control ◽  
Control Strategy ◽  
Rolling Force ◽  
Rolling Process ◽  
Strip Width ◽  
Rolled Material ◽  
Feed Forward Control ◽  
The Stability ◽  
Hot Rolled

This paper proposes an automatic control strategy of the strip width in cold rolling process. The prediction model for the exit strip width of each stand is established. In addition to the strip width variation of the incoming hot-rolled material between the measured and the pre-set values, the variations of the rolling force, tension, bending force and the roll shift amount of each stand are utilized to model and forecast the stand exit width deformation. Then, the model can be used to determine the compensation values of the different profile adjustment mechanism and the exit strip width can be controlled in high accuracy. In this way, the effect of the strip width variation of the incoming hot-rolled material and the fluctuation of the stand rolling process parameters on the exit strip width can be eliminated. Moreover, the feed-forward control of the strip width can reduce the incidence of abnormal situation, such as the strip breakage and off-tracking ,and improve the stability of the cold rolling process.

scholarly journals Twinning Behavior in Cold-Rolling Ultra-Thin Grain-Oriented Silicon Steel

Crystals ◽  
2021 ◽  
Vol 11 (2) ◽  
pp. 187
Author(s):  
Bo Zhang ◽  
Li Meng ◽  
Guang Ma ◽  
Ning Zhang ◽  
Guobao Li ◽  
...  
Keyword(s):  
Cold Rolling ◽  
Rolling Process ◽  
Silicon Steel ◽  
Mechanical Work ◽  
Area Fraction ◽  
Raw Material ◽  
Rolling Reduction ◽  
Cold Rolling Reduction ◽  
Schmid Factor ◽  
Twinning System

Twinning behaviors in grains during cold rolling have been systematically studied in preparing ultra-thin grain-oriented silicon steel (UTGO) using a commercial glassless grain-oriented silicon steel as raw material. It is found that the twinning system with the maximum Schmid factor and shear mechanical work would be activated. The area fraction of twins increased with the cold rolling reduction. The orientations of twins mainly appeared to be α-fiber (<110>//RD), most of which were {001}<110> orientation. Analysis via combining deformation orientation simulation and twinning orientation calculation suggested that {001}<110> oriented twinning occurred at 40–50% rolling reduction. The simulation also confirmed more {100} <011> oriented twins would be produced in the cold rolling process and their orientation also showed less deviation from ideal {001}<110> orientation when a raw material with a higher content of exact Goss oriented grains was used.

FEM Analysis of Profile Control Capability during Rolling in a 6-High CVC Cold Rolling Mill

2014 ◽  
Vol 988 ◽  
pp. 257-262 ◽  
Author(s):  
Ke Zhi Linghu ◽  
Zheng Yi Jiang ◽  
Fei Li ◽  
Jing Wei Zhao ◽  
Meng Yu ◽  
...  
Keyword(s):  
Cold Rolling ◽  
Rolling Mill ◽  
Rolling Force ◽  
Fem Analysis ◽  
Continuous Variable ◽  
Cold Rolling Mill ◽  
Strip Rolling ◽  
Roll Bending ◽  
Profile Control ◽  
Control Capability

A 3D elastic-plastic finite element method (FEM) model of cold strip rolling for 6-high continuous variable crown (CVC) rolling mill was developed. The rolling force distributions were obtained by the internal iteration processes. The calculated error has been significantly reduced by the developed model. the absolute error between the simulated results and the actual values is obtained to be less than 10μm, and relative error is less than 1%. The developed model is significant in investigating the profile control capability of the CVC cold rolling mill in terms of work roll bending, intermediate roll bending and intermediate roll shifting.

Thickness Indirect Measurement Method for Direct Pulling Pilot Cold Rolling Mill

2011 ◽  
Vol 189-193 ◽  
pp. 2670-2674
Author(s):  
Zhi Jie Jiao ◽  
Chun Yu He ◽  
Jian Ping Li ◽  
Xiang Hua Liu
Keyword(s):  
Cold Rolling ◽  
Rolling Mill ◽  
Measurement Method ◽  
Rolling Process ◽  
Indirect Measurement ◽  
Cold Rolling Mill ◽  
Movement Data ◽  
Program Flow ◽  
New Type ◽  
Exit Speed

Pilot cold rolling mill is the important tool for the cold rolling process researching and new steel grade development. According to the design of the new type direct pulling pilot cold rolling mill, based on the mass flow constant principle, strip exit thickness indirect measurement method is studied. During rolling, strip entry and exit speed can be calculated accurately according to the measured value of two sides’ clamps movement. Data filtering treatment is adopted and program flow chart is designed. Based on the material entry thickness measured manually, exit thickness of all passes can be measured indirectly. This thickness indirect measurement method has been applied successfully on the new type pilot cold rolling mill, and the measurement results show that this method has a good accuracy.

Surface inclusions and their evolution on strip rolled on CSP line and in following cold rolling process

2009 ◽  
Vol 36 (7) ◽  
pp. 548-554 ◽  
Author(s):  
Y. Z. Zhu ◽  
J. Rao ◽  
Z. Zhu ◽  
Z. D. Xiang ◽  
Z. F. Wu
Keyword(s):  
Cold Rolling ◽  
Rolling Process
Sign in / Sign up

Export Citation Format

Share Document