scholarly journals Effect of turbulence on the wake of a wall-mounted cube

2016 ◽  
Vol 804 ◽  
pp. 513-530 ◽  
Author(s):  
R. Jason Hearst ◽  
Guillaume Gomit ◽  
Bharathram Ganapathisubramani
Keyword(s):  
Boundary Layer ◽  
Turbulent Boundary Layer ◽  
Turbulence Intensity ◽  
Free Stream ◽  
Reattachment Length ◽  
Free Stream Turbulence ◽  
Boundary Layer Development ◽  
Image Velocimetry ◽  
Shedding Frequency ◽  
Layer Development

The influence of turbulence on the flow around a wall-mounted cube immersed in a turbulent boundary layer is investigated experimentally with particle image velocimetry and hot-wire anemometry. Free-stream turbulence is used to generate turbulent boundary layer profiles where the normalised shear at the cube height is fixed, but the turbulence intensity at the cube height is adjustable. The free-stream turbulence is generated with an active grid and the turbulent boundary layer is formed on an artificial floor in a wind tunnel. The boundary layer development Reynolds number ($Re_{x}$) and the ratio of the cube height ($h$) to the boundary layer thickness ($\unicode[STIX]{x1D6FF}$) are held constant at $Re_{x}=1.8\times 10^{6}$ and $h/\unicode[STIX]{x1D6FF}=0.47$. It is demonstrated that the stagnation point on the upstream side of the cube and the reattachment length in the wake of the cube are independent of the incoming profile for the conditions investigated here. In contrast, the wake length monotonically decreases for increasing turbulence intensity but fixed normalised shear – both quantities measured at the cube height. The wake shortening is a result of heightened turbulence levels promoting wake recovery from high local velocities and the reduction in strength of a dominant shedding frequency.

Free-Stream Turbulence and Pressure Gradient Effects on Heat Transfer and Boundary Layer Development on Highly Cooled Surfaces

1985 ◽  
Vol 107 (1) ◽  
pp. 54-59 ◽  
Author(s):  
K. Rued ◽  
S. Wittig
Keyword(s):  
Heat Transfer ◽  
Boundary Layer ◽  
Free Stream ◽  
Boundary Layer Transition ◽  
Pressure Gradients ◽  
Layer Transition ◽  
Free Stream Turbulence ◽  
Boundary Layer Development ◽  
Gradient Effects ◽  
Layer Development

Heat transfer and boundary layer measurements were derived from flows over a cooled flat plate with various free-stream turbulence intensities (Tu = 1.6–11 percent), favorable pressure gradients (k = νe/ue2•due/dx = 0÷6•10−6) and cooling intensities (Tw/Te = 1.0–0.53). Special interest is directed towards the effects of the dominant parameters, including the influence on laminar to turbulent boundary layer transition. It is shown, that free-stream turbulence and pressure gradients are of primary importance. The increase of heat transfer due to wall cooling can be explained primarily by property variations as transition, and the influence of free-stream parameters are not affected.

Free-Stream Turbulence Effects on Convex-Curved Turbulent Boundary Layers

1989 ◽  
Vol 111 (1) ◽  
pp. 66-72 ◽  
Author(s):  
S. M. You ◽  
T. W. Simon ◽  
J. Kim
Keyword(s):  
Boundary Layer ◽  
Turbulent Boundary Layer ◽  
Turbulence Intensity ◽  
Free Stream ◽  
Skin Friction Coefficient ◽  
Radius Of Curvature ◽  
Free Stream Turbulence ◽  
Curvature Effects ◽  
Asymptotic Shape ◽  
Turbulence Effects

Free-stream turbulence intensity effects on a convex-curved turbulent boundary layer are investigated. An attached fully turbulent boundary layer is grown on a flat plate and is then introduced to a downstream section where the test wall is convexly curved, having a constant radius of curvature. Two cases, with free-stream turbulence intensities of 1.85 and 0.65 percent, are discussed. They were taken in the same facility and with the same strength of curvature, δ/R = 0.03−0.045. The two cases have similar flow conditions upon entry to the curve, thus separating the free-stream turbulence effects under study from other effects. The higher turbulence case displayed stronger curvature effects on the skin friction coefficient Cf, and on streamwise-normal and shear stress profiles, than observed in the lower turbulence case. Observations of this are: (1) As expected, the higher turbulence case has a higher Cf value ( ∼ 5 percent) upstream of the curve than does the lower turbulence case, but this difference diminishes by the end of the curve. (2) Streamwise turbulence intensity profiles, differing upstream of the curve for the two cases, are found to be similar near the end of the curve, thus indicating that the effect of curvature is dominating over the effect of free-stream turbulence intensity. Many effects of curvature observed in the lower turbulence intensity case, and reported previously, e.g., a dramatic response to the introduction of curvature and the rapid assumption of an asymptotic shape within the curve, are also seen in the higher turbulence case.

scholarly journals The Development of the Profile Boundary Layer in a Turbine Environment

1986 ◽  
Author(s):  
J. Hourmouziadis ◽  
F. Buckl ◽  
P. Bergmann
Keyword(s):  
Boundary Layer ◽  
Free Stream ◽  
Rotor Blades ◽  
Turbulence Structure ◽  
Test Results ◽  
Free Stream Turbulence ◽  
Boundary Layer Development ◽  
Wake Effects ◽  
Actual Flow ◽  
Layer Development

Cascade testing tries to simulate the actual flow conditions encountered in a turbine. However, it is neither possible to reproduce the free stream turbulence structure of the turbomachinery, nor the periodic wake effects of upstream blade rows. The usual understanding is that the latter in particular results in a significantly different behaviour of the boundary layer in the engine. Experimental results from cascades and turbine rigs are presented. Grid generated free stream turbulence structure is compared to that in the turbine. Measurements of the profile pressure distribution, flush mounted hot films and flow visualization were used for the interpretation of the test results. Some observations of the boundary layer development in the cascade, on the guide vanes and on rotor blades with typically skewed boundary layers are shown indicating essentially similar behaviour in all cases.

The Development of the Profile Boundary Layer in a Turbine Environment

1987 ◽  
Vol 109 (2) ◽  
pp. 286-295 ◽  
Author(s):  
J. Hourmouziadis ◽  
F. Buckl ◽  
P. Bergmann
Keyword(s):  
Boundary Layer ◽  
Free Stream ◽  
Rotor Blades ◽  
Turbulence Structure ◽  
Test Results ◽  
Free Stream Turbulence ◽  
Boundary Layer Development ◽  
Wake Effects ◽  
Actual Flow ◽  
Layer Development

Cascade testing tries to simulate the actual flow conditions encountered in a turbine. However, it is possible to reproduce neither the free-stream turbulence structure of the turbomachinery, nor the periodic wake effects of upstream blade rows. The usual understanding is that the latter in particular results in a significantly different behavior of the boundary layer in the engine. Experimental results from cascades and turbine rigs are presented. Grid-generated free-stream turbulence structure is compared to that in the turbine. Measurements of the profile pressure distribution, flush-mounted hot films, and flow visualization were used for the interpretation of the test results. Some observations of the boundary layer development in the cascade, on the guide vanes, and on rotor blades with typically skewed boundary layers are shown indicating essentially similar behavior in all cases.

Sign in / Sign up

Export Citation Format

Share Document