scholarly journals Analysis on the Potential Performance of GPS and Galileo Precise Point Positioning using Simulated Real-Time Products

2018 ◽  
Vol 72 (1) ◽  
pp. 19-33 ◽  
Author(s):  
Francesco Basile ◽  
Terry Moore ◽  
Chris Hill
Keyword(s):  
Real Time ◽  
Precise Point Positioning ◽  
Satellite System ◽  
Convergence Time ◽  
Alternative Methods ◽  
International Gnss Service ◽  
Binary Offset Carrier ◽  
Time Service ◽  
Point Positioning ◽  
The Impact

With the evolving Global Navigation Satellite System (GNSS) landscape, the International GNSS Service (IGS) has started the Multi-GNSS Experiment (MGEX) to produce precise products for new generation systems. Various analysis centres are working on the estimation of precise orbits, clocks and bias for Galileo, Beidou and Quasi-Zenith Satellite System (QZSS) satellites. However, at the moment these products can only be used for post-processing applications. Indeed, the IGS Real-Time service only broadcasts Global Positioning System (GPS) and Globalnaya Navigatsionnaya Sputnikovaya Sistema (GLONASS) corrections. In this research, a simulator of multi-GNSS observations and real-time precise products has been developed to analyse the performance of GPS-only, Galileo-only and GPS plus Galileo Precise Point Positioning (PPP). The error models in the simulated orbits and clocks were based on the difference between the GPS Real-Time and the Final products. Multiple scenarios were analysed, considering different signals combined in the Ionosphere Free linear combination. Results in a simulated open area environment show better performance of the Galileo-only case over the GPS-only case. Indeed, up 33% and 29% of improvement, respectively, in the accuracy level and convergence time can be observed when using the full Galileo constellation compared to GPS. The dual constellation case provides good improvements, in particular in the convergence time (47% faster than GPS). This paper will also consider the impact of different linear combinations of the Galileo signals, and the potential of the E5 Alternative Binary Offset Carrier (AltBOC) signal. Even though it is significantly more precise than E5a, the PPP performance obtained with the Galileo E1-E5a combination is either better or similar to the one with Galileo E1-E5. The reason for this inconsistency was found in the use of the ionosphere free combination with E1. Finally, alternative methods of ionosphere error mitigation are considered in order to ensure the best possible positioning performance from the Galileo E5 signal in multi-frequency PPP.

Precise Point Positioning Model Using Triple GNSS Constellations: GPS, Galileo and BeiDou

2016 ◽  
Vol 10 (4) ◽  
Author(s):  
Akram Afifi ◽  
Ahmed El-Rabbany
Keyword(s):  
Real Time ◽  
Urban Areas ◽  
Precise Point Positioning ◽  
Convergence Time ◽  
Dual Frequency ◽  
Post Processing ◽  
International Gnss Service ◽  
Time Service ◽  
System Bias ◽  
Point Positioning

AbstractThis paper introduces a comparison between dual-frequency precise point positioning (PPP) post-processing model, which combines the observations of three different GNSS constellations, namely GPS, Galileo, and BeiDou and real-time PPP model. A drawback of a single GNSS system such as GPS, however, is the availability of sufficient number of visible satellites in urban areas. Combining GNSS observations offers more visible satellites to users, which in turn is expected to enhance the satellite geometry and the overall positioning solution. However, combining several GNSS observables introduces additional biases, which require rigorous modelling, including the GNSS time offsets and hardware delays. In this paper, a GNSS post-processing PPPP model is developed using ionosphere-free linear combination. The additional biases of the GPS, Galileo, and BeiDou combination are accounted for through the introduction of a new unknown parameter, which is identified as the inter-system bias, in the PPP mathematical model. Natural Resources Canada’s GPSPace PPP software is modified to enable a combined GPS / Galileo / BeiDou PPP solution and to handle the newly inter-system bias. A total of four data sets at four IGS stations are processed to verify the developed PPP model. Precise satellite orbit and clock products from the IGS-MGEX network are used to correct of the GPS, Galileo and BeiDou measurements. For the real-time PPP model the corrections of the satellites orbit and clock are obtained through the international GNSS service (IGS) real-time service (RTS). GPS and Galileo Observations are used for the GNSS RTS-IGS PPP model as the RTS-IGS satellite products are not available for BeiDou satellites. This paper provides the GNSS RTS-IGS PPP model using different satellite clock corrections namely: IGS01, IGC01, IGS01, and IGS03. All PPP models results of convergence time and positioning precision are compared to the traditional GPS-only PPP model. It is shown that combining GPS, Galileo, and BeiDou observations in a PPP model reduces the convergence time by 25 % compared with the GPS-only PPP model.

scholarly journals Precise Point Positioning Using the Regional BeiDou Navigation Satellite Constellation

2014 ◽  
Vol 67 (3) ◽  
pp. 523-537 ◽  
Author(s):  
Aigong Xu ◽  
Zongqiu Xu ◽  
Xinchao Xu ◽  
Huizhong Zhu ◽  
Xin Sui ◽  
...  
Keyword(s):  
Real Time ◽  
Precise Point Positioning ◽  
Satellite System ◽  
Convergence Time ◽  
Asia Pacific ◽  
Satellite Orbits ◽  
Navigation Satellite ◽  
Asia Pacific Region ◽  
Point Positioning

On 27 December 2012 it was announced officially that the Chinese Navigation Satellite System BeiDou (BDS) was able to provide operational services over the Asia-Pacific region. The quality of BDS observations was confirmed as comparable with those of GPS, and relative positioning in static and kinematic modes were also demonstrated to be very promising. As Precise Point Positioning (PPP) technology is widely recognized as a method of precise positioning service, especially in real-time, in this contribution we concentrate on the PPP performance using BDS data only. BDS PPP in static, kinematic and simulated real-time kinematic mode is carried out for a regional network with six stations equipped with GPS- and BDS-capable receivers, using precise satellite orbits and clocks estimated from a global BDS tracking network. To validate the derived positions and trajectories, they are compared to the daily PPP solution using GPS data. The assessment confirms that the performance of BDS PPP is very comparable with GPS in terms of both convergence time and accuracy.

scholarly journals Multi-GNSS Combined Precise Point Positioning Using Additional Observations with Opposite Weight for Real-Time Quality Control

2019 ◽  
Vol 11 (3) ◽  
pp. 311 ◽  
Author(s):  
Wenju Fu ◽  
Guanwen Huang ◽  
Yuanxi Zhang ◽  
Qin Zhang ◽  
Bobin Cui ◽  
...  
Keyword(s):  
Quality Control ◽  
Real Time ◽  
Precise Point Positioning ◽  
Satellite System ◽  
Convergence Time ◽  
Navigation Satellite ◽  
Positioning Accuracy ◽  
Global Navigation ◽  
Point Positioning ◽  
Global Navigation Satellite

The emergence of multiple global navigation satellite systems (multi-GNSS), including global positioning system (GPS), global navigation satellite system (GLONASS), Beidou navigation satellite system (BDS), and Galileo, brings not only great opportunities for real-time precise point positioning (PPP), but also challenges in quality control because of inevitable data anomalies. This research aims at achieving the real-time quality control of the multi-GNSS combined PPP using additional observations with opposite weight. A robust multiple-system combined PPP estimation is developed to simultaneously process observations from all the four GNSS systems as well as single, dual, or triple systems. The experiment indicates that the proposed quality control can effectively eliminate the influence of outliers on the single GPS and the multiple-system combined PPP. The analysis on the positioning accuracy and the convergence time of the proposed robust PPP is conducted based on one week’s data from 32 globally distributed stations. The positioning root mean square (RMS) error of the quad-system combined PPP is 1.2 cm, 1.0 cm, and 3.0 cm in the east, north, and upward components, respectively, with the improvements of 62.5%, 63.0%, and 55.2% compared to those of single GPS. The average convergence time of the quad-system combined PPP in the horizontal and vertical components is 12.8 min and 12.2 min, respectively, while it is 26.5 min and 23.7 min when only using single-GPS PPP. The positioning performance of the GPS, GLONASS, and BDS (GRC) combination and the GPS, GLONASS, and Galileo (GRE) combination is comparable to the GPS, GLONASS, BDS and Galileo (GRCE) combination and it is better than that of the GPS, BDS, and Galileo (GCE) combination. Compared to GPS, the improvements of the positioning accuracy of the GPS and GLONASS (GR) combination, the GPS and Galileo (GE) combination, the GPS and BDS (GC) combination in the east component are 53.1%, 43.8%, and 40.6%, respectively, while they are 55.6%, 48.1%, and 40.7% in the north component, and 47.8%, 40.3%, and 34.3% in the upward component.

scholarly journals Performance Evaluation of Real-Time Precise Point Positioning with Both BDS-3 and BDS-2 Observations

Sensors ◽  
2020 ◽  
Vol 20 (21) ◽  
pp. 6027
Author(s):  
Lin Pan ◽  
Xuanping Li ◽  
Wenkun Yu ◽  
Wujiao Dai ◽  
Cuilin Kuang ◽  
...  
Keyword(s):  
Real Time ◽  
Precise Point Positioning ◽  
Rapid Development ◽  
Satellite System ◽  
Convergence Time ◽  
Static Mode ◽  
The Real ◽  
Point Positioning ◽  
Time Critical

For time-critical precise applications, one popular technology is the real-time precise point positioning (PPP). In recent years, there has been a rapid development in the BeiDou Navigation Satellite System (BDS), and the constellation of global BDS (BDS-3) has been fully deployed. In addition to the regional BDS (BDS-2) constellation, the real-time stream CLK93 has started to support the BDS-3 constellation, indicating that the real-time PPP processing involving BDS-3 observations is feasible. In this study, the global positioning performance of real-time PPP with BDS-3/BDS-2 observations is initially evaluated using the datasets from 147 stations. In the east, north and upward directions, positioning accuracy of 1.8, 1.2 and 2.5 cm in the static mode, and of 6.7, 5.1 and 10.4 cm in the kinematic mode can be achieved for the BDS-3/BDS-2 real-time PPP, respectively, while the corresponding convergence time with a threshold of 10 cm is 32.9, 23.7 and 32.8 min, and 66.9, 42.9 and 69.1 min in the two modes in the three directions, respectively. To complete this, the availability of BDS-3/BDS-2 constellations, the quality of BDS-3/BDS-2 real-time precise satellite products, and the BDS-3/BDS-2 post-processed PPP solutions are also analyzed. For comparison, the results for the GPS are also presented.

scholarly journals Evaluation of Inter-System Bias between BDS-2 and BDS-3 Satellites and Its Impact on Precise Point Positioning

2020 ◽  
Vol 12 (14) ◽  
pp. 2185 ◽  
Author(s):  
Wen Zhao ◽  
Hua Chen ◽  
Yang Gao ◽  
Weiping Jiang ◽  
Xuexi Liu
Keyword(s):  
Precise Point Positioning ◽  
Satellite System ◽  
Navigation Satellite ◽  
International Gnss Service ◽  
Beidou Navigation Satellite System ◽  
System Bias ◽  
Point Positioning ◽  
Kinematic Ppp ◽  
The Impact

The BeiDou navigation satellite system (BDS) currently has 41 satellites in orbits and will reach its full constellation following the launch of the last BDS satellite in June 2020 to provide navigation, positioning, and timing (PNT) services for global users. In this contribution, we investigate the characteristics of inter-system bias (ISB) between BDS-2 and BDS-3 and verify whether an additional ISB parameter should be introduced for the BDS-2 and BDS-3 precise point positioning (PPP). The results reveal that because of different clock references applied for BDS-2 and BDS-3 in the International GNSS Service (IGS) precise satellites clock products and the inconsistent code hardware delays of BDS-2 and BDS-3 for some receiver types, an ISB parameter needs to be introduced for BDS-2 and BDS-3 PPP. Further, the results show that the ISB can be regarded as a constant within a day, the value of which is closely related to the receiver type. The ISB values of the stations with the same receiver type are similar to each other, but a great difference may be presented for different receiver types, up to several meters. In addition, the impact of ISB on PPP has also been studied, which demonstrates that the performance of kinematic PPP could be improved when ISB is introduced.

scholarly journals Precise Point Positioning Using Triple GNSS Constellations in Various Modes

2021 ◽  
Author(s):  
Akram Afifi ◽  
Ahmed El-Rabbany
Keyword(s):  
Linear Combination ◽  
Real Time ◽  
Precise Point Positioning ◽  
Satellite Orbit ◽  
Convergence Time ◽  
Dual Frequency ◽  
Post Processing ◽  
Time Service ◽  
Reference Satellite ◽  
Point Positioning

This paper introduces a new dual-frequency precise point positioning (PPP) model, which combines the observations from three different global navigation satellite system (GNSS) constellations, namely GPS, Galileo, and BeiDou. Combining measurements from different GNSS systems introduces additional biases, including inter-system bias and hardware delays, which require rigorous modelling. Our model is based on the un-differenced and between-satellite single-difference (BSSD) linear combinations. BSSD linear combination cancels out some receiver-related biases, including receiver clock error and non-zero initial phase bias of the receiver oscillator. Forming the BSSD linear combination requires a reference satellite, which can be selected from any of the GPS, Galileo, and BeiDou systems. In this paper three BSSD scenarios are tested; each considers a reference satellite from a different GNSS constellation. Natural Resources Canada’s GPSPace PPP software is modified to enable a combined GPS, Galileo, and BeiDou PPP solution and to handle the newly introduced biases. A total of four data sets collected at four different IGS stations are processed to verify the developed PPP model. Precise satellite orbit and clock products from the International GNSS Service Multi-GNSS Experiment (IGS-MGEX) network are used to correct the GPS, Galileo, and BeiDou measurements in the post-processing PPP mode. A real-time PPP solution is also obtained, which is referred to as RT-PPP in the sequel, through the use of the IGS real-time service (RTS) for satellite orbit and clock corrections. However, only GPS and Galileo observations are used for the RT-PPP solution, as the RTS-IGS satellite products are not presently available for BeiDou system. All post-processed and real-time PPP solutions are compared with the traditional un-differenced GPS-only counterparts. It is shown that combining the GPS, Galileo, and BeiDou observations in the post-processing mode improves the PPP convergence time by 25% compared with the GPS-only counterpart, regardless of the linear combination used. The use of BSSD linear combination improves the precision of the estimated positioning parameters by about 25% in comparison with the GPS-only PPP solution. Additionally, the solution convergence time is reduced to 10 minutes for the BSSD model, which represents about 50% reduction, in comparison with the GPS-only PPP solution. The GNSS RT-PPP solution, on the other hand, shows a similar convergence time and precision to the GPS-only counterpart.

Performance Evaluation of Kinematic BDS/GNSS Real-Time Precise Point Positioning for Maritime Positioning

2018 ◽  
Vol 72 (1) ◽  
pp. 34-52 ◽  
Author(s):  
Fuxin Yang ◽  
Lin Zhao ◽  
Liang Li ◽  
Shaojun Feng ◽  
Jianhua Cheng
Keyword(s):  
Real Time ◽  
Precise Point Positioning ◽  
Cost Effective ◽  
Satellite System ◽  
Convergence Time ◽  
Kinematic Data ◽  
Position Accuracy ◽  
Global Positioning ◽  
Cost Effective Technique ◽  
Point Positioning

Real-time Precise Point Positioning (PPP) has been evolved as a cost-effective technique for highly precise maritime positioning. For a long period, maritime PPP technology has mainly relied on the Global Positioning System (GPS). With the revitalisation of GLONASS and the emerging BeiDou navigation satellite system (BDS), it is now feasible to investigate real-time navigation performance of multi-constellation maritime PPP with GPS, BDS and GLONASS. In this contribution, we focus on maritime PPP performance using real world maritime kinematic data and real-time satellite correction products. The results show that BDS has lower position accuracy and slower convergence time than GPS. The BDS and GPS combination has the best performance among the dual-constellation configurations. Meanwhile, the integration of BDS, GLONASS and GPS significantly improves the position accuracy and the convergence time. Some outliers in the single constellation configuration can be mitigated when multi-constellation observations are utilised.

scholarly journals Precise Point Positioning Using Triple GNSS Constellations in Various Modes

2021 ◽  
Author(s):  
Akram Afifi ◽  
Ahmed El-Rabbany
Keyword(s):  
Linear Combination ◽  
Real Time ◽  
Precise Point Positioning ◽  
Satellite Orbit ◽  
Convergence Time ◽  
Dual Frequency ◽  
Post Processing ◽  
Time Service ◽  
Reference Satellite ◽  
Point Positioning

This paper introduces a new dual-frequency precise point positioning (PPP) model, which combines the observations from three different global navigation satellite system (GNSS) constellations, namely GPS, Galileo, and BeiDou. Combining measurements from different GNSS systems introduces additional biases, including inter-system bias and hardware delays, which require rigorous modelling. Our model is based on the un-differenced and between-satellite single-difference (BSSD) linear combinations. BSSD linear combination cancels out some receiver-related biases, including receiver clock error and non-zero initial phase bias of the receiver oscillator. Forming the BSSD linear combination requires a reference satellite, which can be selected from any of the GPS, Galileo, and BeiDou systems. In this paper three BSSD scenarios are tested; each considers a reference satellite from a different GNSS constellation. Natural Resources Canada’s GPSPace PPP software is modified to enable a combined GPS, Galileo, and BeiDou PPP solution and to handle the newly introduced biases. A total of four data sets collected at four different IGS stations are processed to verify the developed PPP model. Precise satellite orbit and clock products from the International GNSS Service Multi-GNSS Experiment (IGS-MGEX) network are used to correct the GPS, Galileo, and BeiDou measurements in the post-processing PPP mode. A real-time PPP solution is also obtained, which is referred to as RT-PPP in the sequel, through the use of the IGS real-time service (RTS) for satellite orbit and clock corrections. However, only GPS and Galileo observations are used for the RT-PPP solution, as the RTS-IGS satellite products are not presently available for BeiDou system. All post-processed and real-time PPP solutions are compared with the traditional un-differenced GPS-only counterparts. It is shown that combining the GPS, Galileo, and BeiDou observations in the post-processing mode improves the PPP convergence time by 25% compared with the GPS-only counterpart, regardless of the linear combination used. The use of BSSD linear combination improves the precision of the estimated positioning parameters by about 25% in comparison with the GPS-only PPP solution. Additionally, the solution convergence time is reduced to 10 minutes for the BSSD model, which represents about 50% reduction, in comparison with the GPS-only PPP solution. The GNSS RT-PPP solution, on the other hand, shows a similar convergence time and precision to the GPS-only counterpart.

Sign in / Sign up

Export Citation Format

Share Document