Flow and Fracture Phenomena in Adsorbed Protein Layers at the Air/Water Interface in Connection with Spreading Oil Droplets

Langmuir ◽  
2003 ◽  
Vol 19 (24) ◽  
pp. 10210-10216 ◽  
Author(s):  
Natalie E. Hotrum ◽  
Martien A. Cohen Stuart ◽  
Ton van Vliet ◽  
George A. van Aken
Author(s):  
Boris Kichatov ◽  
Alexey Korshunov ◽  
Vladimir Sudakov ◽  
Vladimir Gubernov ◽  
Andrey Kolobov ◽  
...  

Langmuir ◽  
2002 ◽  
Vol 18 (4) ◽  
pp. 1238-1243 ◽  
Author(s):  
Anneke Martin ◽  
Martin Bos ◽  
Martien Cohen Stuart ◽  
Ton van Vliet

Author(s):  
Natalie E Hotrum ◽  
Martien A Cohen Stuart ◽  
Ton van Vliet ◽  
George A van Aken

1970 ◽  
Vol 116 (4) ◽  
pp. 671-680 ◽  
Author(s):  
P. J. Quinn ◽  
R. M. C. Dawson

1. Measurements have been made of the interaction of cytochrome c, bovine serum albumin and synthetic oxytocin with low-pressure (2dyn/cm) monolayers of stearic acid, phosphatidylcholine and phosphatidylethanolamine. 2. [14C]Carboxymethylation of the cytochrome c and albumin followed by surface-radioactivity determinations have shown that only a proportion of the protein added to the subphase is bound to the monolayers and that initially the degree of binding is dependent on the protein concentration. The binding is irreversible in the sense that the adsorbed protein cannot be removed by transferring the film containing the interacted protein to a fresh subphase containing no protein. 3. Three successive types of interaction can usually be recognized. (a) Initially, whole molecules of protein penetrate the lipid film and occupy the same area as those of the protein spread at the air/water interface. (b) Above certain film pressures a part of each protein molecule, probably hydrophobic side chains, penetrates the film. The change in surface pressure per unit of bound protein is much smaller than in (a). (c) At higher film pressures, adsorption without penetration occurs. With cytochrome c this is initially dependent on a favourable electrostatic interaction.


2007 ◽  
Vol 21 (5-6) ◽  
pp. 906-919 ◽  
Author(s):  
M CEJUDOFERNANDEZ ◽  
C CARRERASANCHEZ ◽  
M ROSARIORODRIGUEZNINO ◽  
J PATINO

Author(s):  
Randall W. Smith ◽  
John Dash

The structure of the air-water interface forms a boundary layer that involves biological ,chemical geological and physical processes in its formation. Freshwater and sea surface microlayers form at the air-water interface and include a diverse assemblage of organic matter, detritus, microorganisms, plankton and heavy metals. The sampling of microlayers and the examination of components is presently a significant area of study because of the input of anthropogenic materials and their accumulation at the air-water interface. The neustonic organisms present in this environment may be sensitive to the toxic components of these inputs. Hardy reports that over 20 different methods have been developed for sampling of microlayers, primarily for bulk chemical analysis. We report here the examination of microlayer films for the documentation of structure and composition.Baier and Gucinski reported the use of Langmuir-Blogett films obtained on germanium prisms for infrared spectroscopic analysis (IR-ATR) of components. The sampling of microlayers has been done by collecting fi1ms on glass plates and teflon drums, We found that microlayers could be collected on 11 mm glass cover slips by pulling a Langmuir-Blogett film from a surface microlayer. Comparative collections were made on methylcel1ulose filter pads. The films could be air-dried or preserved in Lugol's Iodine Several slicks or surface films were sampled in September, 1987 in Chesapeake Bay, Maryland and in August, 1988 in Sequim Bay, Washington, For glass coverslips the films were air-dried, mounted on SEM pegs, ringed with colloidal silver, and sputter coated with Au-Pd, The Langmuir-Blogett film technique maintained the structure of the microlayer intact for examination, SEM observation and EDS analysis were then used to determine organisms and relative concentrations of heavy metals, using a Link AN 10000 EDS system with an ISI SS40 SEM unit. Typical heavy microlayer films are shown in Figure 3.


Sign in / Sign up

Export Citation Format

Share Document