scholarly journals Towards high-power mid-IR light source tunable from 3.8 to 4.5 µm by HBr-filled hollow-core silica fibres

2022 ◽  
Vol 11 (1) ◽  
Author(s):  
Zhiyue Zhou ◽  
Zefeng Wang ◽  
Wei Huang ◽  
Yulong Cui ◽  
Hao Li ◽  
...  

AbstractFibre lasers operating at the mid-IR have attracted enormous interest due to the plethora of applications in defence, security, medicine, and so on. However, no continuous-wave (CW) fibre lasers beyond 4 μm based on rare-earth-doped fibres have been demonstrated thus far. Here, we report efficient mid-IR laser emission from HBr-filled silica hollow-core fibres (HCFs) for the first time. By pumping with a self-developed thulium-doped fibre amplifier seeded by several diode lasers over the range of 1940–1983 nm, narrow linewidth mid-IR emission from 3810 to 4496 nm has been achieved with a maximum laser power of about 500 mW and a slope efficiency of approximately 18%. To the best of our knowledge, the wavelength of 4496 nm with strong absorption in silica-based fibres is the longest emission wavelength from a CW fibre laser, and the span of 686 nm is also the largest tuning range achieved to date for any CW fibre laser. By further reducing the HCF transmission loss, increasing the pump power, improving the coupling efficiency, and optimizing the fibre length together with the pressure, the laser efficiency and output power are expected to increase significantly. This work opens new opportunities for broadly tunable high-power mid-IR fibre lasers, especially beyond 4 μm.

Pramana ◽  
2014 ◽  
Vol 82 (1) ◽  
pp. 15-27 ◽  
Author(s):  
B N UPADHYAYA

2015 ◽  
Vol 23 (4) ◽  
Author(s):  
D. Stachowiak ◽  
P. Kaczmarek ◽  
K.M. Abramski

AbstractIn this paper our results of investigation on a pump power combiner in a configuration of 7×1 are presented. The performed combiner, with pump power of 80–85% transmission level, was successfully applied in a thulium doped fibre laser. The performed all-fibre laser setup reached a total CW output power of 6.42 W, achieving the efficiency on a 32.1% level.


2011 ◽  
Vol 19 (1) ◽  
Author(s):  
D. Dorosz ◽  
M. Kochanowicz

AbstractIn the paper, the phase-locked emitters in multi-core optical fibres for high power fibre lasers are presented. The influence of the normalized frequency and diameters of the cores on the shape of the pattern in the Fraunhofer diffraction region has been analysed. The simulation of coupling coefficient between cores influences on phase-locking and in the consequence on the far-field pattern of the fibre laser, based on the analyzed multi-core optical fibre, were performed. In the analyzed fibre laser, while exchanging power of the generated radiation between two adjacent cores on the fibre length (L = 5 m) within the range of 4–10%, the radiation becomes phased. Having satisfied this condition, in the far-field low-divergence, high-power laser beam (supermode) is attained. 5-core double clad optical fibre doped with neodymium ions was fabricated. Luminescence spectra of the manufactured fibre were measured.


2005 ◽  
Vol 6-8 ◽  
pp. 171-178 ◽  
Author(s):  
Claus Thomy ◽  
Thomas Seefeld ◽  
Frank Vollertsen

Latest developments in laser physics have enabled the production of high-power fibre lasers with beam powers up to 10 kW at excellent beam quality. Adding to these properties their high energetic efficiency, their considerable estimated lifetime and their compact size, they might well be considered to be a viable alternative to both conventional lamp- or diode-pumped Nd:YAGas well as to CO2-Lasers. However, due to the novelty of the system, very few experiences on their usability for materials processing and in special for welding of steel and aluminium sheet material are existing. To help this situation, a 7 kW high-power fibre laser system was tested at the Bremer Institut fuer angewandte Strahltechnik, and its potentials for welding steel and aluminium sheets have been assessed. By these results, of which a selection is presented here, it could indeed be demonstrated that it is possible to remarkably enhance process limitations considering welding speed and sheet thickness previously regarded to be inevitable when welding with solid-state lasers. Consequently, in July 2004 the first high-power fibre laser with a beam power exceeding 10 kW at a BPP of less than 12.5 mm*mmrad was tested in cooperation with SLV M-V Rostock. This laser source is currently used for developing mainly welding, but also cutting and cladding applications for a variety of industries. Within these studies, it was e. g. demonstrated that it is possible to achieve a penetration of 10 mm in EN-AW 6082 at a welding speed of 3 m/min.


2015 ◽  
Vol 23 (2) ◽  
Author(s):  
J. Kwiatkowski

AbstractAn efficient operation of a Ho:YLF laser pumped by a Tm-doped fibre laser is reported. The research in a continuous-wave (CW) operation was done for two crystals of the same 0.5 at.%Ho dopant concentration and with different lengths (3×3×30 mm


1997 ◽  
Vol 33 (19) ◽  
pp. 1635 ◽  
Author(s):  
D.Z. Garbuzov ◽  
R.J. Menna ◽  
R.U. Martinelli ◽  
J.H. Abeles ◽  
J.C. Connolly

Sign in / Sign up

Export Citation Format

Share Document