A Jug-Shaped CPW-Fed Ultra-Wideband Printed Monopole Antenna for Wireless Communications Networks

A type of telecommunication technology called an ultra-wideband (UWB) is used to provide a typical solution for short-range wireless communication due to large bandwidth and low power consumption in transmission and reception. Printed monopole antennas are considered as a preferred platform for implementing this technology because of its alluring characteristics such as light weight, low cost, ease of fabrication, integration capability with other systems, etc. Therefore, a compact-sized ultra-wideband (UWB) printed monopole antenna with improved gain and efficiency is presented in this article. Computer simulation technology microwave studio (CSTMWS) software is used to build and analyze the proposed antenna design technique. This broadband printed monopole antenna contains a jug-shaped radiator fed by a coplanar waveguide (CPW) technique. The designed UWB antenna is fabricated on a low-cost FR-4 substrate with relative permittivity of 4.3, loss tangent of 0.025, and a standard height of 1.6 mm, sized at 25 mm × 22 mm × 1.6 mm, suitable for wireless communication system. The designed UWB antenna works with maximum gain (peak gain of 4.1 dB) across the whole UWB spectrum of 3–11 GHz. The results are simulated, measured, and debated in detail. Different parametric studies based on numerical simulations are involved to arrive at the optimal design through monitoring the effects of adding cuts on the performance of the proposed antennas. Therefore, these parametric studies are optimized to achieve maximum antenna bandwidth with relatively best gain. The proposed patch antenna shape is like a jug with a handle that offers greater bandwidth, good gain, higher efficiency, and compact size.

A Novel Piezoelectric RF-MEMS Resonator with Enhanced Quality Factor

This work presents a novel ultra-high frequency (UHF) Lamb mode Aluminum Nitride (AlN) piezoelectric resonator with enhanced quality factors (Q). With slots introduced in the vicinity of the tether support end, the elastic waves leaking from the tether sidewalls can be reflected, which effectively reduces the anchor loss while retaining size compactness and mechanical robustness. Comprehensive analysis was carried out to provide helpful guidance for obtaining optimal slot designs. For various resonators with frequencies ranging from 630 MHz to 1.97 GHz, promising Q enhancements up to 2 times have all been achieved. The 1.97 GHz resonator implemented excellent f × Q product up to 6.72 × 1012 and low motional resistance down to 340 Ω, which is one of the highest performances among the reported devices. The devices with enhanced Q values as well as compact size could have potential application in advanced RF front end transceivers.

Multi–Disciplinary Optimizations of Small-Scale Gravitational Vortex Hydropower (SGVHP) System through Computational Hydrodynamic and Hydro–Structural Analyses

Hydropower is a superior energy extraction approach, which has been made to work based on renewable energy sources. In the generation of hydropower, Gravitational Vortex Hydropower (GVHP) plays a predominant contributor role because of its free turbulence-relayed energy utilization concept and flexible as well as compact size. Owing to the huge contribution of GVHP in the hydropower sector, multi-objective-based investigations have emerged. However, there is still insufficient literature available for the technology to precede optimum turbine blade design. Two important categories are involved in these multidisciplinary investigations, in which the first phase, a numerical investigation has been done using ANSYS to identify the location of maximum tangential velocity in a conical basin with different notch angles, conical angles, basin shapes, anddiameters. In this second phase, the focal aim is to carry out the numerical investigation on Gravitation Vortex Turbine Blades (GVTB) for the different geometry in order to get the optimum power output with a high structural lifetime through HSI (Hydro–Structural Interaction) computation. The entire conceptual designs of this SGVHP and its hydro-rotors are modeled with the help of CATIA. ANSYS Fluent is a CFD (Computational Fluid Dynamics) numerical tool, which is primarily used in this paper for all the hydrodynamic analyses. Finally, the standard analytical approaches are used for the comparative determinations of thrust production by hydro-rotors, power extraction by hydro-rotors, and propulsive efficiency for the selection process of best hydro-rotors. HSI analyses are additionally carried out and thereby the suitable lightweight material is picked.

Compact Broadband Circularly Polarized CPW-Fed Antenna with Characteristic Mode Analysis

A compact circularly polarized (CP) antenna is proposed for low-profile and wideband operation based on characteristic mode analysis (CMA). A ring patch with a gap and two arc-shaped metallic stubs as the radiator is analyzed and optimized by CMA to figure out the orthogonal modes and operating frequency band for potential good axial ratio (AR) performance. The studies of these CP modes provide a physical insight into the property of broadband circular polarization. Such an in-depth understanding paves the way for the proposal of novel CP antenna with separation between the design of radiator and feeding network. A 50-Ω coplanar waveguide (CPW) is introduced and placed appropriately to excite the desired modes based on the information from CMA, which employs two asymmetric ground planes to improve the performance in terms of AR and impedance matching. The antenna with a compact size of 0.71λ0 × 0.76λ0 × 0.038λ0 (λ0 is the free-space wavelength at the center frequency of the 3-dB AR bandwidth) is fabricated and measured for validation. The realized gain varies from 1.6 to 3.1 dBic over the operating bandwidth characterized by the measured 10-dB impedance bandwidth of 83.8% (3.98–9.72 GHz) and 3-dB AR bandwidth of 70.3% (4.59–9.57 GHz), respectively.

Marimo actuated rover systems

Background The potential to directly harness photosynthesis to make actuators, biosensors and bioprocessors has been previously demonstrated in the literature. Herein, this capability has been expanded to more advanced systems — Marimo Actuated Rover Systems (MARS) — which are capable of autonomous, solar powered, movement. Results We demonstrate this ability is both a practical and viable alternative to conventional mobile platforms for exploration and dynamic environmental monitoring. Prototypes have been successfully tested to measure their speed of travel and ability to automatically bypass obstacles. Further, MARS is electromagnetically silent, thus avoiding the background noise generated by conventional electro/mechanical platforms which reduces instrument sensitivity. The cost of MARS is significantly lower than platforms based on conventional technology. Conclusions An autonomous, low-cost, lightweight, compact size, photosynthetically powered rover is reported. The potential for further system enhancements are identified and under development.

Neuromorphic Chip Integrated with an LSI and Amorphous-metal-oxide Semiconductor Thin-film Synapse Devices

Artificial intelligences are promising in future societies, and neural networks are typical technologies with the advantages such as self-organization, self-learning, parallel distributed computing, and fault tolerance, but their size and power consumption are large. Neuromorphic systems are biomimetic systems from the hardware level, with the same advantages as living brains, especially compact size, low power, and robust operation, but some well-known ones are non-optimized systems, so the above benefits are only partially gained, for example, machine learning is processed elsewhere to download fixed parameters. To solve these problems, we are researching neuromorphic systems from various viewpoints. In this study, a neuromorphic chip integrated with an LSI and amorphous-metal-oxide semiconductor (AOS) thin-film synapse devices has been developed. The neuron elements are digital circuit, which are made in an LSI, and the synapse devices are analog devices, which are made of the AOS thin film and directly integrated on the LSI. This is the world's first hybrid chip where neuron elements and synapse devices of different functional semiconductors are integrated, and local autonomous learning is utilized, which becomes possible because the AOS thin film can be deposited without heat treatment and there is no damage to the underneath layer, and has all advantages of neuromorphic systems.

Environmental Impact of EV Batteries and Their Recycling

Electrifying transportation is one of the biggest keys to solving the looming climate crisis. The demand for electric vehicles (EV) is booming in the last five years and will increase in the coming years. In this modern age, where EV is the finest means of transportation due to null exhaust gases, there is a dire need to think about ways of recycling and reusing those batteries associated with EVs. In this context, it is estimated that post-vehicle battery packs application will be crossed from 1.4 million to 6.8 million by the year 2035. Numerous researches have been done on the re-purposing and safe disposal of EV batteries. However, presently, Lithium-ion batteries (LiBs) are the optimal choice for electric transportation due to greater energy density, compact size, and extended life cycles. Nonetheless, the trade-off between re-purposing and disposal of LiBs is substantial for the protection of the environment and human health. Regrettably, Lithium-ion battery recycling percentage is only 3% currently whereas its revival is negligible.

Review: Observation on CFD Analysis of ZnO and TiO2 Nanofluid with Oil and Ethylene Glycol in Square and Helical Coil Heat Exchanger

Helically coiled heat exchangers are globally used in various industrial applications for their high heat transfer performance and compact size. Nanofluids can provide the excellent thermal performance in helical coil heat exchangers. Research studies on heat transfer enhancement have gained serious momentum during recent years and have been proposed many techniques by different research groups [1]. A fluid with higher thermal conductivity has been developed to increase the efficiency of heat exchangers. The dispersion of 1-100nm sized solid nanoparticles in the traditional heat transfer fluids, termed as nanofluids, exhibit substantial higher convective heat transfer than that of traditional heat transfer fluids. Nanofluid is a heat transfer fluid which is the combination of nanoparticles and base fluid that can improve the performance of heat exchanger systems. In this present paper the efforts are made to understand that how to compare the heat transfer rate in Copper helically coiled tube and squared coiled tube heat exchanger using Zinc Oxide and Titanium Dioxide Nano fluid by studying research papers of various authors. Keywords: Helical Coil, Nano-fluid, Heat Exchanger, CFD, Pressure Drop, Temperature Distribution.

Compact dual-mode microstrip bandpass filter based on slotted square patch resonator

Purpose The purpose of this paper is to present the design of a compact microstrip bandpass filter (BPF) in dual-mode configuration loaded with cross-loop and square ring slots on a square patch resonator for C-band applications. Design/methodology/approach In the proposed design, the dual-mode response for the filter is realized with two transmission zeros (TZs) by the insertion of a perturbation element at the diagonal corner of the square patch resonator with orthogonal feed lines. Such TZs at the edges of the passband result in better selectivity for the proposed BPF. Moreover, the cross-loop and square ring slots are etched on a square patch resonator to obtain a miniaturized BPF. Findings The proposed dual-mode microstrip filter fabricated in RT/duroid 6010 substrate using PCB technology has a measured minimum insertion loss of 1.8 dB and return loss better than 24.5 dB with a fractional bandwidth (FBW) of 6.9%. A compact size of 7.35 × 7.35 mm2 is achieved for the slotted patch resonator-based dual-mode BPF at the center frequency of 4.76 GHz. As compared with the conventional square patch resonator, a size reduction of 61% is achieved with the proposed slotted design. The feasibility of the filter design is confirmed by the good agreement between the measured and simulated responses. The performance of the proposed filter structure is compared with other dual-mode filter works. Originality/value In the proposed work, a compact dual-mode BPF is reported with slotted structures. The conventional square patch resonator is deployed with cross-loop and square ring slots to design a dual-mode filter with a square perturbation element at its diagonal corner. The proposed filter exhibits compact size and favorable performance compared to other dual-mode filter works reported in literature. The aforementioned design of the dual-mode BPF at 4.76 GHz is suitable for applications in the lower part of the C-band.