scholarly journals Bioconjugatable, PEGylated hydroporphyrins for photochemistry and photomedicine. Narrow-band, near-infrared-emitting bacteriochlorins

2016 ◽  
Vol 40 (9) ◽  
pp. 7750-7767 ◽  
Author(s):  
Nuonuo Zhang ◽  
Jianbing Jiang ◽  
Mengran Liu ◽  
Masahiko Taniguchi ◽  
Amit Kumar Mandal ◽  
...  

PEGylated bacteriochlorins are soluble in water, can be excited in the ultraviolet, and exhibit a narrow fluorescence band in the NIR spectral region.

2016 ◽  
Vol 40 (9) ◽  
pp. 7721-7740 ◽  
Author(s):  
Mengran Liu ◽  
Chih-Yuan Chen ◽  
Amit Kumar Mandal ◽  
Vanampally Chandrashaker ◽  
Rosemary B. Evans-Storms ◽  
...  

PEGylated chlorins are soluble in water, can be excited in the near-ultraviolet, and exhibit a relatively narrow fluorescence band in the red spectral region.


2019 ◽  
Vol 28 (7) ◽  
pp. 9-16
Author(s):  
Shich-Chuan Wu ◽  
Yu-Lin Yang ◽  
Wen-Hsien Huang ◽  
Yang-Tung Huang

1988 ◽  
Vol 41 (2) ◽  
pp. 225 ◽  
Author(s):  
RFC Brown ◽  
KJ Coulston ◽  
FW Eastwood ◽  
MJ Irvine ◽  
ADE Pullin

Five compounds were investigated as precursors for the pyrolytic generation of pentatetraenone, H2C=C=C=C=C=O. These were (1)-(4): 3- ethenylidenebicyclo [2.2.1]hept-5-ene with the following 2,2 substituents : H, COOCOCF3 (1); H, 13COOCOCF3 (1′); (COOCOCF3)2 (2); (COO)2C(CH3)(OCH3) (3); (COO)2Si(CH3)2 (4) and 5-(3′- methylenebicyclo [2.2.1]hept-5′-en-2′-ylidene)-2,2-dimethyl-1,3-dioxan-4,6-dione (5). The five precursors were pyrolysed in a stream of argon at temperatures in the range 350-725°C and the pyrolysate -argon mixture condensed on a CsI plate at c. 10 K. Infrared spectra were obtained between 4000 and 250 cm-1. All five precursors gave two strong bands in the spectral region 2070-2250 cm-1, possibly attributable to pentatetraenone. At lower pyrolytic temperatures the more intense of the two bands was a broad band centred at c. 2128 cm-1 [precursors (1)- (4)] or at c. 2094 cm-1 [precursor (5)]. At higher pyrolytic temperatures these bands were diminished in intensity and replaced by a narrow band at 2207 cm-1 for all five precursors. Bands due to the expected other products for each pyrolysis reaction to form pentatetraenone were observed. H2C413CO ( pentatetraenone substituted by 13C at the carbonyl carbon atom) was prepared by pyrolysis of precursor (1′). We assign the broad bands at c. 2128 cm-1 [precursors (1)-(4)] and at c. 2094 [precursor (5)] to incompletely pyrolysed precursor in which cyclopentadiene has been retained but decomposition in the rest of the molecule has resulted in formation of a =C=C=O group. Bands at 2207, 2068 and 1726 cm-1 we assign to v2-v4 of pentatetraenone. Corresponding bands at 2168, 2056 and 1720 cm-1 are observed in the spectrum of H2C413CO.


2000 ◽  
Vol 54 (3) ◽  
pp. 450-455 ◽  
Author(s):  
Stephen R. Lowry ◽  
Jim Hyatt ◽  
William J. McCarthy

A major concern with the use of near-infrared (NIR) spectroscopy in many QA/QC laboratories is the need for a simple reliable method of verifying the wavelength accuracy of the instrument. This requirement is particularly important in near-infrared spectroscopy because of the heavy reliance on sophisticated statistical vector analysis techniques to extract the desired information from the spectra. These techniques require precise alignment of the data points between the vectors corresponding to the standard and sample spectra. The National Institute of Standards and Technology (NIST) offers a Standard Reference Material (SRM 1921) for the verification and calibration of mid-infrared spectrometers in the transmittance mode. This standard consists of a 38 μm-thick film of polystyrene plastic. While SRM 1921 works well as a mid-infrared standard, a thicker sample is required for use as a routine standard in the near-infrared spectral region. The general acceptance and proven reliability of polystyrene as a standard reference material make it a very good candidate for a cost-effective NIR standard that could be offered as an internal reference for every instrument. In this paper we discuss a number of the parameters in a Fourier transform (FT)-NIR instrument that can affect wavelength accuracy. We also report a number of experiments designed to determine the effects of resolution, sample position, and optics on the wavelength accuracy of the system. In almost all cases the spectral reproducibility was better than one wavenumber of the values extrapolated from the NIST reference material. This finding suggests that a thicker sample of polystyrene plastic that has been validated with the SRM 1921 standard would make a cost-effective reference material for verifying wavelength accuracy in a medium-resolution FT-NIR spectrometer.


Sign in / Sign up

Export Citation Format

Share Document